Counting matching models…
I needed a mount for my scarlet 2i2 to declutter my desk, so I drew up this design, intended to mount wit 4 countersunk screws. The audio interface slides in and is held in place through a tight friction fit, sturdy enough to not move…
Remix of @Christoph_79778 's Scarlett 2i2 mount, widened to match the dimensions of the newer 4th Gen.
Does not require support material Print with back face (power cord plugin area) on the print bed
Support à fixer sous un bureau ou un plan de travail pour la carte son Focusrite Scarlett 2i4 2nd Gen et 2i2 2nd Gen Je voulais un support qui me permette de sortir la carte de son logement en cas de besoin. Attention, les languettes sont…
I previously had a Scarlett 2i2 Gen 2 mounted under my desk with the mount from ziller88 . After the Interface died i bought a 2i2 Gen4 and modified the mount to work with the new interface. It comes in 4 Versions: Scarlett 2i2 Gen4 desk…
Je ne trouvais pas de supports pour les Focusrite Scarlett 2i2 3rd Gen donc j'en ai fait un car ce modèle est bien plus petit que ses prédécesseurs. Je me suis inspiré de ce support https://www.thingiverse.com/thing:3647280 pour faire…
You can use this model to mount you FOCUSRITE SCARLETT 2I2 under the table. Category: Music
Focusrite Scarlett 2i2 - Vertical Stand.
A bracket to mount the Focusrite Scarlet 2i2 3rd gen. audio interface under the desk top. It has countersunk screw holes, but can also be attached with hot glue or double-sided adhesive tape, the only question is whether the latter will…
This mounts a Focus Scarlett 2i2 audio interface (3rd generation) under a desk or table. It includes a large hook for headphones below. There is a smaller hook in back for extra loops of headphone cable. I modeled this in Fusion360. Along…
This is a edit of Ziller88's design. His file for 1st gen has the incorrect foot-groove size and would not work with 1st gen devices (Serial number's starting with S) If you don't know what generation your device is, see this link:…
This is a Focusrite Scarlett 2i2 Mount for the Balolo setup cockpit
See “Differences” below for more information
Mount for Focusrite Scarlett 2i2
The Focusrite Scarlett 2i2 4th Gen is a lovely USB audio interface with an iconic look! However, the red metallic chassis doesn't fit in with every aesthetic around it. In my case, I was building a digital piano setup, and the original…
Pretty shelf for the 2i2! Two STL files available, one also has the top side indent that I use for my Minimixer, as seen in the picture. The other one has a smooth top. Edit: After a while I realized it's actually perfect for holding it…
Focusrite 4i4v4 under surface mount with screws. I left a little space for soft velcro to cushion it. If you don't use that, take about 1mm off the mounts. I included a pattern to drill holes with
A simple, low-cost, easy-to-print, Scarlett 2i2 Gen 4 Under Desk Mount that uses 3M Command Large Picture Hanging Strips Print Settings Choose your preferred model: Raised or Flat. Use Raised if your table has a 20 mm thick metal bar like…
La caja está diseñada para transportar la tarjeta de sonido Focusrite Scarlett 2i2, pero también es válida para la Scarlett solo, dentro cabe la tarjeta con su soporte y bolsa de tela. Está diseñada para poner la tarjeta en la parte…
No supports needed, printed in Pla with ender 3 printer.
A vertical stand I made for my gen 4 Scarlett 2i2! Made to be stable while visually unobtrusive. :) Doesn't cover the XLR or USB ports on the back regardless of its orientation. You can add rubber feet under the base if you want to get…
Remixed this Focusrite Scarlett 2i2 under desk mount so that it uses Multiconnect slots to mount instead of the screw holes. Printed with the same orientation as the original, and no supports needed. I printed this in PETG, which has…
Soporte para tarjeta de sonido Focusrite Scarlett 2i2
I had my focusrite velcroed to the underside of my desk; but it kept falling off. So, I made this holder. It's designed to use the velcro-style removable double-sided adhesive mounting tape. Print instructions I printed mine in Prusament…
Added a void in the bottom for the feet to “rest” so they do not have to be removed, i wanted to keep mine stock in case i ever wanted to desk mount it again. The feet could vary slightly in its locations hence i made a big void instead…
Print settings Material: PLA Supports: organic/tree (refer to screenshot)
Under table mount for Focusrite Scatlett 2i2 (4th gen). Also for bigger versions as you can place brackets as you want to.
Ideal for more permanant installations to reduce cable clutter. Designed with short right angle male to female connectors in mind. The version with_slot adds an additonal cable slot to route cables, e.g. keyboard/mouse usb under the unit.…
There are slots for rubber strips on the bottom piece to prevent slipping.
This 3D model was designed by me and created for practical use. -No supports -pla -I attached it wit Powerstrips
A under desk mount for my old Focusrite Scarlett 2i2 and my new FiiO K13 R2R. I realize that pretty much no one will have this exact combo, but since one of my viewers asked for it, I figured I just might upload it. Especially for those…
I peeled the rubber bumpers off the bottom and attached them to the case itself. You would have to do this if you want the audio interface to fit in the case. Its snug enough for it to not slide around. very easy to take off if needed…
The Focusrite Scarlett 2i2 (4th gen) has a circular volume LED around the input 1 and 2 inputs. At the time of this file's creation, there is no software solution for disabling it. This knob was designed to block out that light. This knob…
I originally used two of my initial remix to hold the audio interface up. It eventually stretched out the brackets and fell out. The single, center hole design of the original bracket doesn't seem to do well with heavy and/or wide…
NOTE: completed a 3rd revision of this model that works with all 2i2 generations as it started to sag over time with PLA. Check my profile for the updated stand. Focusrite 2i2 (1st gen) monitor stand platform with cable hooks, reversible…
This holder is to neatly mount your Focusrite Scarlett 2i2 under the desk in a vertical orientation.
(I make this model with the feet removed in mind.) first model i do. i tried to make a clip to keep it from going back when you plug something in it but it kept breaking. i added some lines inside so it's pretty snugged and does not move…
Focusrite 2i2 (all generations!) monitor stand platform with cable hooks, reversible (mirror) for left and right mounting. Depending on your generation the 2i2 may sit a little loose inside the platform, if you would like a snug fit it…
This desktop stand is designed to hold your Scarlett 2i2 3rd Gen and Elgato 4K X. It keeps everything organized and easily accessible. No screws, mounts, or extra setup needed. Remove the rubber feet from the Scarlett, drop the file into…
This is a custom box mount for my Klark Technik CM-2 preamp so that I could put it directly on my interface (Scarlett 2i2). Keeps everything in place as one unit for a cleaner desk. Printed with default supports in BambuStudio. All other…
Note: Superseded by an all-generations compatible build, please see my profile for the latest revision. Focusrite 2i2 (3rd gen, also kind of works with 1st gen) monitor stand platform with cable hooks, reversible (mirror) for left and…
The parts dont build up any unnecessary depth in the rack and keep all Ports free in the front and the back Part - 2i2 - Part Total width : 253mm // 39mm - 175mm - 39mm Total depth : 87mm You obviously need to print it twice! As fixation…
I "upcycled" a sound card from Focusrite (broken one, power layer HS). Fit to the raspberry pi 3. I designed it to place my octoprint server + 12v/5v converter + switch to control the 12vLED light of my printerbox and the raspberry pi. A…
Extended the length of the original author's creation to accommodate a full 1U traditional rack space. Printed with Elegoo petg on my Elegoo CC1. I printed it at a lower infill but I do recommend you print it with a higher infill for…
Focusrite Scarlett 2i2 Wall and SKADIS Mount Move your Scarlett 2i2 off the desk and onto a wall or SKADIS pegboard, with the front-panel controls and inputs still within reach. Need a custom part for your setup? I design print-ready…
A2I20D020GNR1 3D model can be used in cad software
Simple design - two sturdy brackets to mount a 3rd Gen Focusrite Scarlett 2i2 audio interface under a desk. There are no screwholes as I just used double sided tape. NOTE : The print in the picture was stopped early - the model is the…
Ideal for more permanant installations to reduce cable clutter. Designed with short right angle male to female connectors in mind. The version with_slot adds an additonal cable slot to route cables, e.g. keyboard/mouse usb under the unit.…
The Focusrite Scarlett 2i2 (4th gen) has a circular volume LED around the input 1 and 2 inputs. At the time of this file's creation, there is no software solution for disabling it. This knob was designed to block out that light. This knob…
Vertical stand for Scarlett 2i2 and Hyperdrive 12-port.
![Scarlett 2i2 Studio [4Gen] under Desk mount](https://media.printables.com/media/prints/b68b4700-3848-405d-b901-74fde379532b/images/11786680_3c32e39d-e46f-4922-b98f-9b2ac1437c51_c89430e2-26eb-434b-b8f3-26d8c4719788/639045345285121010.png)
