Counting matching models…
Basic 45° small double switch track compatible with Brio, IKEA Lillabo (old plastic dogbone and current wooden-only version too), Thomas Train, Kaufland, LIDL Playtive, kmart, ebay,... wooden tracks. Support: NO, Infill: 15 %. CHECK OUT…
Basic 45° small switch track compatible with Brio, IKEA Lillabo (old plastic dogbone and current wooden-only version too), Thomas Train, Kaufland, LIDL Playtive, kmart, ebay,... wooden tracks. Support: NO, Infill: 15 %. CHECK OUT other…
Zeros to about 50m but Elev. and Windage is adjustable. Requires: 1x M2x~10mm 1x M3x~23mm + nut 2x M5x~25mm Not all picattiny is manufactured within the same tolerances thus sanding may be necessary.
Summary: iPhone monitor mount in order to view it in landscape mode to use the Standby features or watch videos, etc. Takes a little over 30 minutes to print on Bambu PLA settings. Description: No need for supports. Fits any magsafe…
Basic 45° short curved track compatible with Brio, IKEA Lillabo (old plastic dogbone and current wooden-only version too), Thomas Train, Kaufland, LIDL Playtive, kmart, ebay,... wooden tracks. Support: NO, Infill: 15 %. CHECK OUT other…
Customized version of https://www.thingiverse.com/thing:735038 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=735038 Convert a 60mm fan to a 40mm mounting for extra cooling on a 3D printer. An extra 10mm…
This is simple yet useful adapter when your frame has 20x20mm mount holes but the FC is 25.5x25.5. Fits M2 screws and screw heads are hidden so when mounted everything is flat.
This is a 45 degree version of the "Drybox filament guide using PTFE tube" made by @mp42, available for OD4mm and OD3mm PTFE tube. If the inside diameter of the fitting is too tight, it may need to be adjusted.
I thought that the under dash tray was very usefull, but on some toll streets it is usefull to have a handy cardholder for credit card or toll billets To mount put double sided tape inside the small joint on top and press it with some…
Print as shown in screen shots with flat (non-track) side down to plate.
4 prepared models, one for each size (2, 3, 4, and 5mm). Attachment is mounted on threaded end, like most of dremel's accesories. Works with 3mm metal Bur, that i got with big assecories kit from Aliexpress
I combined a few versions of 45deg filament sensor mounts from other people designs into my own. Parts needed 1x M3x25 Bolt (or 2x) 1x M3x12 Bolt 2x M3 Nut
Hello i used 2 magnets and printed the 15mm pin and the wheel At the 15mm pin, glued on a 10x10x5mm magnet. And the other magnet is round 8x3mm, to go on the hole in the extruder. Printed this in PLA with green to yellow color change…
Holding the power strip at 45 degrees makes it easy to mount plugs and power adapters, allowing for cables that go both down and upwards from the socket. Very sturdy in PLA with 20% infill, a good snug fit for Masterplug extension power…
Simple desk stand that mounts to the BTT Panda Touch using 2 voron spec/CNC kitchen M3 heatset inserts
One Adapter to the standard Balsa Strip Cutter to cut precise 45° deg Stipes Is easy to clip on the origirnal one , and to remove offer a better handling and very easy to print, no support ~ 1hour @ 0,3mm Print Settings Printer Brand:…
Simple Wall Mount I designed via Tinkercad. Two versions: Camera hangs on M3-Bolts (two M3 Nuts & two M3x20 needed) Camera hangs on printed knobs (Supports needed printing) Tested with SCD620 and SCD843 (there may be more Camera Versions…
A Stand for the Audient EVO 8 affectionately titled "the cradle", which holds the unit at a pleasing 45 degree angle
“The Cradle” I was sick and tired of my Audient Evo 4 shuffling around my desk… As someone who only has this interface for an overkill XLR mic utilized at my remote job, I haven't cared enough about aesthetics, until now. Given that the…
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
13,1cm wide, 19,8cm long. Tilted 45 degrees If you would like to support me - you can buy me a coffee :) Also if you liked the model - share photo of your print <3 Check out my other models HERE Any feedback will be highly appreciated!…
I built this model to hold a non-epoxied 10mm LED strip. It is designed specifically for a under-cabinet lighting situation that holds the LED strip at a 45 degree angle. I like the 45 degree angle because it then I can't see the LEDs…
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
A mount for attaching self adhesive led strips to an 8020 series 10 beam at a 45 deg. angle. There are three different sizes provided so that you can mix and match to come close to the length you need. This has been sized to fit 8020…
This is a ¼" version of the a model by @mixon, which is a 45 degree version of the "Drybox filament guide using PTFE tube" made by @mp42, available for OD4mm and OD3mm PTFE tube. If the inside diameter of the fitting is too tight, it may…
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Same electrics needed as the Original Model. Hardware changed: Needed Screws: 2× M1.6 6mm screw instead of the 10mm For Lid and Bearing guide 6× M3 8mm countersunk screws For attaching the Motorhousing to the body 4× M3 10-12mm…
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Corner channel base and diffuser covers for mounting LED strips to shelves or cabinets. It may not be the most refined design, but it's all printable without supports. All pieces are easily modifiable in slicer to fit your specific use…
A pool has an outlet and an inlet. This part is for the inlet to redirect the water in a 45degree angle. To the bottom or to the center. The adapter has a diameter of around ~47mm. 2mm thread distance and a single starting thread. Source…
I wanted to add lights to my Prusa MK3 to make prints easier to see, and for monitoring when I may want the room lights off. This design uses a 6in LED strip, and is mounted with 3mm bolts. I use one light on each side of the top frame.…
Filament Runoutsensor by BTT (SFS v2.0) on inside, but under 45 degree angle. Original cable used on Trident-300.
I needed a phone stand which can be fixed to a car dash board on a defined position and orientation (using Velcro) and which could handle a variation of different phones I used M3 heated inserts and m3 screws to assembly but you can also…
small jewelry box stackable, easy to print Filament: All PLA nozzle 0.4 no support needed infill 7% Gyroide 2 layers top and bottom
This mount was made to attach a UP-Floodlight to a fascia panel that's shorter than the light itself, and also aim the light to its right instead of straight forward (flip LR in your slicer for opposite angle). This is not endorsed by…
A Stand for the Audient EVO 8 affectionately titled "the cradle", which holds the unit at a pleasing 45 degree angle
This is a ¼" version of the a model by @mixon, which is a 45 degree version of the "Drybox filament guide using PTFE tube" made by @mp42, available for OD4mm and OD3mm PTFE tube. If the inside diameter of the fitting is too tight, it may…
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Overview TexRC KerbTex Large Radius (600mm) 45deg Corner to fit 65mm square downpipe. The corner can be used to connect downpipes sections together to create an RC car track. See my other projects for 90 degree corners and hairpins.…
I have a Dyson Animal, and it's too big to fit under the bed. When I use the wand attachment the angle is incorrect, so the carpet attachment does not work. I have made my own 45 degree adapter, allowing the wand to be lowered closer to…
2020 aluminum extrusion 45deg 3 way corner
45 deg mount for Reolink POE bell with top hole to accommodate a threaded compression fit adapter for 20mm conduit as to allow it to friction fit/self tap as it is screwed in.
45deg 15mm coolant ball for cnc lathe, designed for use with od turning tools to provide a more direct flow of coolant to the insert. I recommend using a brim and printing with petg or abs/asa for higher strength and temperature resistance.
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Type of corner / connector allowing to build a number of bespoke gates for Whoop Drone Racing. Fits 20mm or 22mm PCV Other Drone Accessories here: https://www.printables.com/@StudioMechanik/collections/3053772
Requires m5x12mm bolts and m5 nuts, fit is tight on the nuts so just hammer them in place.
use 5 pcs M5x16 2 pcs M5 nuts 3 pcs M5 T-nuts If you like my design feel free to tip my design https://www.paypal.me/Djdenzo Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No Resolution: 0,24 Infill: 30%…
Affix from side with 4x conical screws of maximum diameter of 2mm.
i just wanted something functional and mnimalist that would work w/ a few different things i was working on, and it did. i printed in petg and flexed a little to make it work, i dont think it would work in pla or pc Category: DIY
When scraping something off of a build plate the thing being scraped would get stuck on the leading edge of the clip since it was perpendicular to the axis of the blade. I modified the clip to have a chamfer to allow pieces to slide up…
DIN rail for wall mounting and connection with M6 bar Print instructions Category: Hobby Print Settings Rafts: No Supports: No Resolution: 0.1 Infill: 15
osVAC-Adapter für 58-mm-Stecker. Tested for older Metabo circular saw, Metabo BAS261 band saw, Record Power BDS 150 belt sander. Two version, straight and angled at 45° Category: Tools
In a dust collection system the max elbow you should use is a 45deg sweep. I have tried to keep my system to no more than 30deg. But now with the addition of the new wood lathe space became a problem so here is a 45deg sweep that I needed…
I made a new top button a bit taller and put in slots for M3 nuts. Adding M3 screws (30mm) with nuts reduces plastic fatigue. Insert the nut with one of the nut's chamfered edges pointing out. I Remixed the body also with deeper channels…
This is a quick mashup of the Mk3/2.5 style fan duct but with the mounting points for the mk3s extruder body. This is quick and functional, not perfect. If you like the older shroud with side vents for more all around cooling but you have…
Can be mounted with doublesided adhesive tape or|and with 2mm screw. Prints on the photo are made of Eryone Matte Black PLA
A 45 degree canted mount (right side) for use in conjunction with and optic or something Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: .2 Infill: 20 Filament: random pla black Category: 3D…
About: Prusa Mini Step Motor brace with 45deg blocks. I had to install press button for time lapse and wanted to avoid installing it on the other end of the X axis and was not able to find anything that would suit my need. The vertical…
I needed a diffuser and holder for 8mm an LED strip, I wanted it to hold at a 45deg angle The diffuser is printed in white PETG, clear did not diffuse enough. Scale the light strip in the slicer and make sure everything works properly.…
Replacement because mine melted down. It happens occasionally. Printed in ABS, of course.
