Counting matching models…
Needed to make covers for terminals and mounting brackets so I made a simple model. PSU looked good enough to share. Still working on the terminal covers and mounting brackets. Will upload those when they're finished.
No screws required, 2 clamps are used instead to hold the 2 enclosure parts together and also serve as feet. Steps to assemble: 1. Place the board into the bottom of the enclosure. 2. Place the top of the enclosure over the bottom one. 3.…
Spojka pro ruční mixér SSMS 600 C3 z Lidlu. Když se zasekl nástroj tak původní spojka povolila v tisícihranu a motor se otáčel naprázdno dál. Tím neříkám že tahle nepovolí... Netuším jestli je to nejlepší volba, ale tiskl jsem z PLA, 100%…
The Ryobi plunge router came with a clear dust collector piece that attaches a vacuum hose vertically to it. It is prone to cracking and I didn't like the angle of the vacuum hose coming out. It also wouldn't work with my new camlock…
Drop in replacement for original broken clutch (white on photo) Need use some force to connect. Push motor down to clutch laying on desk. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Doesn't Matter Supports: No Resolution:…
Housing for the 600W DC-DC Boost Converter. There are a few different versions. Take a look at included photo for comparison. LED should be bended 90°, so it points at the side. Small adjustment holes have guides so screwdriver hits…
Description The stock power supply for Qidi Q2 is 350W which barely powers the system. I personally replaced it with a 600W PS from MeanWell, Model No. LRS-600-24 . It's not mandatory, but a plus for better system operation. This model…
Cannot find sth for my powersuply Here is Cover + Holder Check dimentions before print.
The printed parts must be glued and completed with one o-ring, after which they can be used to repair the domestic ASIST water plant.
The original back cover of this hairdryer likes to suck in hair. I made a new one to stop this. This is my first OpenSCAD model I printed it at 0.2mm with traditional grid supports. The supports were a bit difficult to remove.
Tisknuto na Ender 3 bez úprav, jen v případě ABS s boxem. Vyzkoušeno materiál PLA a ABS PLA Hotend 200 Bed 70 Tryska 0,4 Vrstva 0,16 a 0,20 vyzkoušeno Infill 20% a výš ABS Hotend 240 Bed 110 Tryska 0,4 Vrstva 0,16 a 0,20 V boxu (bez něj…
I made this new air filter assembly since the original required you to unscrew a bracket every time you wished to clean the filters and as you might imagine these things are often located in cellars or other dusty compartments and as such…
First step to reduce the noise of my TL D3 Pro: Outsource the PSU. It also dramatically reduces implied heat inside the printer. Win-Win. Mind if you fasten the PSU to the case not to use SCREWS LONGER THAN 10mm, Metric Hex M4x10 works…
decidi modelar e imprimir uma peça de substituição em 3D. Funcionou perfeitamente e agora quero partilhar a solução com a comunidade!
The Ryobi plunge router came with a clear dust collector piece that attaches a vacuum hose vertically to it. It is prone to cracking and I didn't like the angle of the vacuum hose coming out. It also wouldn't work with my new camlock…
Recently I purchased a new USB charger, advertised and sold as "USB C Charger Block 600W 8 Port GaN Fast Charging Station Hub" (see photos). Five years ago I made a tablet charging stand (see remix link ), which I am still using today. Of…
Description The stock power supply for Qidi Q2 is 350W which barely powers the system. I personally replaced it with a 600W PS from MeanWell, Model No. LRS-600-24 . It's not mandatory, but a plus for better system operation. This model…
If you happen to have this buck converter you might find this housing useful. It is designed to be printed without supports. There are openings on the main body so the voltage can be adjusted from and the wires screwed without…
A cover covering industrial PSU into Lab/safe tool. includes banana, XT60 and EC5 connection options
10" rack mount for generic 600W GaN charger (mine was 34x74x108)
Recently I purchased a new USB charger, advertised and sold as "USB C Charger Block 600W 8 Port GaN Fast Charging Station Hub" (see photos). Five years ago I made a tablet charging stand (see remix link ), which I am still using today. Of…
replacement part of the connection between the hose and the main body, the inner thread ande safety lock was removed so that the type of hose could be replaced, and the lock works by friction. Better with raft No internal supports PLA or…
Holder for attachments and mixer for convenient storage. For greater stability, you can glue it to the surface with double-sided tape. PETG, PLA, ABS. ALL MATERIAL.
replacement part for the hoose connector of the samsung air track 1600 Sugested to print on a side of the model, for more strengh in the lock system. No special parameters to print, just the setup we work on your printer better work with…
