Counting matching models…
04/08/2025: I was going to print a barrel cooler using the 5015 fan when I saw the 6015 fan was a little cheaper and flowed 50% more air (2.9cfm vs 4.5cfm)! That's a big jump for only 10mm growth in size. These 3D printer fans flow much…
I designed this model because I couldn't find any like it with a fan and snap-fit features for my new 3D printer. The top and bottom covers snap/click into place, eliminating the need for screws there. However, you will need 6x M3x6mm…
Only a 6015 blower fan model. If you need more layer cooling, try this blower. Category: 3D Printer Parts
This model is compatible with the lego system.
This mounts two 60mm fans to the center bed support of the Voron Trident. It will mount them flush to the bottom in order to not take away any Z travel. It could be used to flush mount any 60mm fan on a typical 2020 extrusion. Two step…
I have been printing a lot of ASA/ABS and ran into an issue where Klipper was throwing a code saying the bed couldn't keep up to temperature. i noticed that the SSR was very hot to the touch and needed some active cooling. i threw…
Short version (original here ). Air outlet directed upwards (or not)
The Fan Block Raspberry Pi cases were built to house a 6015 fan, but someone very reasonably pointed out that plenty of people have 4010 fans lying around as remnants from old printers. So, I made an unnecessarily complicated adaptor! The…
Thanks to Tareku for the PSU case cover. I wanted a case cover without a fan grille—since that also generates noise—and a quieter fan. The mounting position for the 92 mm fan didn't seem ideal to me, as there are no vents in the printer…
based on sovol original could be printed in PETG or ABS. I printed in PETG-CF 4 pcs M3x3 inserts are needed
A stepless angle bracket for mounting 6015 COB LED strip. This is a component of an ongoing project, for providing adjustable LED light sources. However, I think this can be practical in a variety of cases, the two M2 holes in the base…
This ia a HoneyComb PSU COVER to replace the original cover. Compatible with 60mmx15mm fan or slimmer. Fits most of the 3D printers Post-Printing For the installation you will need: 4 M3x4mm inserts 4 M3 x 6mm screws Category: 3D Printer…
This APC PDU has dimensions that theoretically makes it fit into 10" rack. However, it is a little bit wide for classical front mounting brackets. This mount uses M5 heat inserts. I printed it in ABS, but other filaments will probably…
This is a replacement suspension arm for the Rlaarlo Rog1 RC car.
After a while the high efficient floor nozzles (also called free-flow) floor nozzles of the Numatic Henry (HRV-160, HRV-170 and so on) fall off. The wheel itself is pretty fine, but there is a little shim inside which wears down easily. I…
This APC PDU has dimensions that theoretically makes it fit into 10" rack. However, it is a little bit wide for classical front mounting brackets. This mount uses M5 heat inserts. I printed it in ABS, but other filaments will probably…
Model redesigned from 0, with reinforced screws support, to be printed without supports. The holes in the ceiling bracket have been enlarged, less material. The corners have been slightly rounded inside and out (AeRoDyNaMiCsSsSs), with…
You can use any print settings as you desire, but these are the ones I used. Perimeters | 3 Layer Height | 0.20mm Infill | 50% Cubic Supports | None needed! Nozzle Size | 0.40mm Hardware I used: Noctua 60x15mm 5V Fan 5V Power Module 8 *…
Thanks to Tareku for the PSU case cover. I wanted a case cover without a fan grille—since that also generates noise—and a quieter fan. The mounting position for the 92 mm fan didn't seem ideal to me, as there are no vents in the printer…
Model redesigned from 0, with reinforced screws support, to be printed without supports. The holes in the ceiling bracket have been enlarged, less material. The corners have been slightly rounded inside and out (AeRoDyNaMiCsSsSs), with…
Bracket for installing a 6015 fan on ramps It must be screwed
"Fan adapter 6015" for Chargery Power S1500 model building power supply unit A fan (D-FAN DFH6010S 60x60x10mm) broke on my power supply unit. A suitable fan that had a little more airflow was one that was 5mm thicker than the original…
The Etekcity EK6015 scale works fine for weighing spools, but it's small and you can't see the display with a spool laying on its side. This model holds the spool upright. Instructions: Place the caddy on the scale and tare it. You should…
