18 models
Being newer to RC flying, I crashed my AeroScout hard enough to fracture the wooden servo & battery tray. It features a built-in lap joint for strength when gluing. I originally tried an existing design by TeslaScorpion , but ended up…
This mount only requires 1 screw in the ceiling and consists of multiple parts that can be printed flat to optimize layer orientation. I found other RC plane mounts lacking because either their hole spacing required mounting into drywall…
This is a quick design I came up with for wingtip armor for the HobbyZone Aeroscout. As a new, inexperienced pilot, I kept scuffing the wingtips of my AeroScout during landings. They aren't a perfect fit and won't keep the aircraft…
Designed for RC-Plane Aeroscout, fits on wheels with approx 76mm diameter and 20mm width. Mounted on wheel, held in place with rubber rings. No disassemble of wheel needed. I printed in PETG with supports.
Print with PLA or PETG (Others might work but those are the one's I've done. I do 0% infill and only 2 top thickness. (this is to reduce weight) Only supports on plate. I flip the bottom 180 so that it doesn't need much supports. Works…
Just add a microservo to the build. You can see and customize the releaser here: https://cad.onshape.com/documents/a2fad6d0cf64304307fcdafe/w/76f1b029aa6d6f58a28d5f7e/e/e2aaab103ed4d49d56a2d02a The wishbang you can see on the picture it's…
Do you have an Aeroscout and want to quickly FPV it! Well now you can! All you need is a AIO FPV+VTX Combo from amazon, a cheap one I use is this FPV Camera 3-in-1 System [1]. You also would need a receiver and I use the VR02 from betafpv…
replacement ESC / receiver tray for hobbyzone aeroscout
This model is to be used with this one: https://www.printables.com/model/1451998-aeroscout-hatch-with-mounts to mount to the Aeroscout RC plane! I used PETG to prevent it melting when the VTX gets hot. 15% infill.
Skis for Aeroscout S2. Thanks to RonStG for the mounting part. use the heat from the heatbed to curve the front of the skis. go check out RonStG on thingiverse! https://www.thingiverse.com/RonStG/designs You can use a rubber band through…
Battery tray for the HobbyZone AeroScout. It lifts the battery by about 2 cm above the servos, preventing interference between the battery, cables and servos. Inspired by the work of Captain Leo.
This is a holder to attach a GoPro Hero 8 Black to the top of a AeroScout.
This print will make your aeroscout a nacelle for a 30mm engine. All you have to do is print and glue.
Can mount to this base: https://www.printables.com/model/1451998-aeroscout-hatch-with-mounts and allows GoPro or small camera to the plane. PLA works but PETG is better. I printed 0% infill and 2 wall top, as well as no supports. It was a…
Put snow skis on your AeroScout S2. It uses all factory hardware. Simply replace the landing wheels with the snow skis and fly in the winter. Canopy and wings are deliberately left off for clarity only. This is not a new design, but…
Here's my mounting plate to fix a CLRacing F4 Air V3 flight controller board into the top bay of the Esky Eagle, also sold as the AeroScout. You'll need to remove the little plywood box in the top bay, then this sits down onto the wood…
Skis for Aeroscout S2. Thanks to RonStG for the mounting part. use the heat from the heatbed to curve the front of the skis. go check out RonStG on thingiverse! https://www.thingiverse.com/RonStG/designs You can use a rubber band through…
Battery tray for the HobbyZone AeroScout. It lifts the battery by about 2 cm above the servos, preventing interference between the battery, cables and servos. Inspired by the work of Captain Leo.
