Counting matching models…
If you like me parts, you can also support me here: https://buymeacoffee.com/andretheengineer :) i didnt like to freely align my pei sheet, since it was never perfect and my self diagnosed ocd was driving my perfectionism crazy. hence i…
These clips are useable with the newest version of the Creality K1 / K1C Unibody Riser: https://www.printables.com/model/891616-creality-k1-k1c-unibody-riser Update 2024-10-25: With the latest version of the Unibody Riser you do not need…
The square clamp/allignment tool can be used to join two plates, using one on the inside and one on the outside. A normal screw clamp can be used to tighten these. Maximum clamp width is 30mm to fit into the recessed space. The model can…
These printed corners snap onto the M3 nut. ABS will soften at elevated temperatures therefore I doubt the press fit will last a lifetime when printing at bed temperatures of 100+. You can use simple superglue (cyanoacrylate) which is…
I was looking for a fused y carriage since i figured it would take human error out of the assembly. Found one model on printables but it was poorly put together and wasn't even aligned properly as one half was sticking out the other. So,…
PEI sheet alignment bracket for Artillery Sidewinder X2, X1 bed. Print the second bracket in mirror image. For the project we need: - 3x PCB with a width of about 10mm or wider, the height should be selected individually according to your…
I got some flashlights compatible with 18650 batteries but the battery would sit crooked. It caused some intermittent connection issues. ~30 minutes of modeling, problem solved. Modeled in 55mm & 61.5mm lengths. https://a360.co/3VaizVz
When installing the BMG extruder (or at least the cloes which I have) require a 4mm gap between the top of the extruder mount and the bottonm of the primary gear on the motors shaft. So I designed a little shim to sit the cog at the right…
DO NOT USE WHEN NOZZLES\HEATER BLOCKS ARE HOT! Description: Zonestar P802QR2 Nozzle Allignment Jig. The jig is an aid to aligning the two hot ends relative to each other. There may be some additional levelling required when levelling…
A simple tool to help align the laser in a laser cutter.
With my first attempt to upgrade my Ikea Lack table with multiconnect wall mounts areound the edges, I have spent a lot of time with a tape measure, speed square and pencil to precisely mark where to place the mounts. Only to find out in…
Simply clutch alignment for Citroen DS / ID post 1965 manual transmission. It is for "3 fingers" pressure plate (see first photo), not for diaphragm one! It's only a tube...no particulary attentions for printing setting Print Settings…
Tile aligners with as reduced as possible weight. Good for most tiles (8mm-10mm thickness of the tiles) Only tested in PLA+ but should work fine with regular PLA Printed in 2 wall thickness with 0.4mm nozzle
I designed this part because I am making my own ender 3 corexy conversion similar to duender, one of the steps I needed was to drill holes at the exact same location on the extrusion, I designed this tool to help me get the extrusions as…
Simply clutch alignment for Citroen DS / ID post 1965 manual transmission. It is for "3 fingers" pressure plate (see first photo), not for diaphragm one! It's only a tube...no particulary attentions for printing setting Print Settings…
You need at least two of these, one for each side of the rail. Place your print head in the middle of the rail, and push down on the x axis until it touches both pins. You must loosen one of the z-axis screw rails at the top for this to…
This is for the Ender Extender 400 AC Powered 600 watt heat pad : I wanted to make sure the AC heat pad was centered as close to perfectly as possible. So I created this simple-to-print guide pin that fits over the build plate screws. Two…
I finally got it tidy and alligned as I wanted :-) Happy to share in case somebody likes the idea! In case you only want the filament sensor bracket and not the z-axis I added a second variant. Parts needed for the z-axis belt: (a) 1 x…
