Counting matching models…
Remix from https://www.thingiverse.com/thing:4841242 Wall mount for the nozzle scaled at 101.5% (the orginal design is too small) Category: Tool Holders & Boxes
The latest mods from Ellie Valkyrie's garage! A whole pile of pipes, blowers and burners to give your Gaslands cars the extra oomph they need to burn rubber around the table (or at least to look like they can.) I printed these without…
Uses various m3 bolts plus four m3 nuts. 3010 heat-sink fan and two 5015 blower fans. Fits CR-10 style heat-sink (Polis3d CR-10 CHC hot-end pictured). Make sure you use the proper bridging angle on the air ducts.
A stubby nozzle for the Dewalt DCBL777 & DCBL772 Flexvolt 60v leaf blower. Great for drying a car or cleaning out tight spaces. Print as oriented with at least 3 walls for strength. No supports needed. Also available with a wider slotted…
A stubby nozzle for the Dewalt DCBL777 & DCBL772 Flexvolt 60v leaf blower. Great for drying a car or cleaning out tight spaces. Print as oriented with at least 3 walls for strength. No supports needed. Also available with a round opening…
The latest mods from Ellie Valkyrie's garage! The latest in Gaslands: Glacierlands equipment to keep your ride roaring like a sabretooth kitten! Requires supports. If you like my work and want to see (and print) more of it, please…
Updated on 09-02-24: Added models “Persano_Duct_for_the_CR6_SE_-_Base_V4” and “Persano_Duct_for_the_CR6_SE_-_Base_V4_stronger”, that has some minor improvements. The stronger one has a thin part below that helps the sides to not bend and…
I had loads of above Aliexpress-average quality Creality's original 4010 blower fans that I decided to fit to A4T toolhead, however it was designed for smaller hubbed versions. I decided to give it a go and just delete some of the…
A few nozzle lengths and shapes for the Yomile / Kukiho / Joco brand air dusters that have the same aluminum body design with the round ~20mm air outlet. Handle length differs depending on size of battery (4000-10000 mAh) but the nozzle…
This model is a recirculating air filter using activated carbon pellets and two 5015 blowers. The screen components have honeycomb infill and were printed with only perimeter layers, no top or bottom layers. I built this for use within a…
Replacement trigger for EGO series leaf blowers. - Works with Power+ series hand-held leaf blowers - May work with the EGO backpack leaf blowers Print with supports and 4-5 walls. Print should be oriented so that the trigger is sideways…
This is a replacement part for a Universal Gutter Cleaning Kit. The broken part, as seen in the pictures, was attached to the blower with hose clamps, so I added a modification to the print to allow it to directly attach to my Echo blower…
Want to go crazy with cooling ? Want to try remote cooling ? 2x5015 blowers laying unused around ? Possibly found PVC pipe 10x2 or 10x1.5mm from old aquarium ? Using CR10-hotend? Rookery looks too big? Then this could be tried. Edit to…
Backstory: The two 3010 fans in my formbot kit were absolute garbage, the one for the hotend started rattling after 3 prints and the one for the electronics had an incredibly annoying loud pitch and barely moved any air. I had two gdstime…
Mount for Anycubic (like) Kossel Plus (linear) delta printer. Contains two different mount points for classic ADXL345 board Fan ducts designed to be printed with TPU filament to work closely to hotend without being melted Designed to be…
After faffing around with the original fan and a variety of fan ducts to fit the original fan I ended up designing a whole new hotend cover to utilise two 5015 fans that I had knocking around from my now redundant ender 3. Pros: Insane…
Replacement part that is similar to MTD 731-1133C. Designed to be printed with TPU with 2 walls, 10% gyroid infill, and supports. Random seams suggested. Snug supports recommended. 0.1mm top interface spacing for supports recommended as…
Why did I design this? The stock cooling of the BIBO 3D printer is rather poor, so I decided to switch to 5015 blowers. There are already a few blower fan ducts on Thingiverse for the BIBO but many of them restrict the build volume.…
Was getting some trash in blowup paint booth so designed a air filter to fit on the 2 paint booth blowup pumps. Zip tie mount. Reduces airflow by about 5-10% but still Plenty of air. Designed around a standard 6 inch engine filter…
A stubby nozzle for the Dewalt DCBL777 & DCBL772 Flexvolt 60v leaf blower. Great for drying a car or cleaning out tight spaces. Print as oriented with at least 3 walls for strength. No supports needed. Also available with a wider slotted…
A stubby nozzle for the Dewalt DCBL777 & DCBL772 Flexvolt 60v leaf blower. Great for drying a car or cleaning out tight spaces. Print as oriented with at least 3 walls for strength. No supports needed. Also available with a round opening…
After faffing around with the original fan and a variety of fan ducts to fit the original fan I ended up designing a whole new hotend cover to utilise two 5015 fans that I had knocking around from my now redundant ender 3. Pros: Insane…
