Counting matching models…
Hier ein Gehäuse für das BigTreeTech Manta M8P für den Cáribou. Es sind jeweils ein Lüfter für die Motortreiber und ein Lüfter für das CM4 Modul vorhanden. Gedruckt habe ich es in PETG und 0,2 Schichthöhe.
This is a holder for Sunlu S2 Filament Dryer on top of my Caribou Duet 420. It will be mounted with 3 screws at the frame. Regarding the print orientation, I ve selected like an orientation like in the attached picture, but you can choose…
Hallo ich wollte mein Meanwell Netzteil leiser haben aber trotzdem die Kühlleistung nicht verlieren. Da wollte ich gleich meinen Noctua NF-R8 benutzen so entschied ich mich für meinen Zaribo dieses Abdeeckung von…
This is a Caribou Duet case for Duet 3 6HC and Raspberry Addon
This is the Bondtech extruder carriage from Caribou3D for Prusa MK3s/+. This would allowed you to replace the existing designed without adjusting the firmware . To me, this multiple pieces x-carrage is eaiser to be installed and helpful…
PanelDue 7i Cover for CaribouDuet This Display Cover attaches the PanelDue 7i to the front of the CaribouDuet 3D-Printer. Print instructions 0.2mm layer height 20% infill No Supports needed
https://caribou3d.com/en/ provides pretty printer kits based on Prusa, so which changes are needed to mod a cr-10s, or similar, this way step by step? PINDA depends to the printbed so I think a PINDA BLTouch replacement shlould be nice.…
This is a Duet Wifi Box it fits the Prusa Mk3s/+ Frame. This is a Remix from Wolfgang Shadows Caribou Duet box Original Design :…
This is a remix based on the original Caribou parts for the all 10mm axis printer to fit a Caribou printer with 8mm X-axis and 10mm Z-axis. The motor holder is ready for the X-axis cable chain. Here you'll find the original Caribou parts:…
This is a remix of the original mounts from Caribou3D for the LDO OLED display to fit onto the Prusa i3 MK3/S/S+. You can use all 4 screws in the Prusa front plate to mount the OLED display. Use the mounts with the original Caribou3D OLED…
Since the OLED display from LDO is "thinner", you need a new cover to replace the original display. The original STL can be found at Caribou3D (by wschadow). Since I haven't done a Caribou printer conversion (yet), I preferred the Prusa…
This is a remix of the original OLED cover from Caribou3D for the LDO OLED display for a cleaner look or to add your own text or logo. I also added the mounts for Prusa i3 MK3/S/S+ (own design based on Caribou parts) and Caribou MK3/S/S+…
When I downloaded this mod, I checked the X tensioner and you will need the original Prusa pulley 623, but If you wanna use Caribou pulley 2gt 16T Toothless, you can check this pulley is “dancing” inside tensioner. I prefer little pulley…
LED Light Bar Holder for Caribou MK3s You need this LED Light Bar (308mm): https://www.amazon.de/gp/product/B07DPJ1KXC/ref=ppx_yo_dt_b_asin_title_o01_s01?ie=UTF8&psc=1 Category: 3D Printer Accessories
UPDATE: @Martin did a much better Job on this !!! https://www.printables.com/de/model/239786-ldo-oled-display-mount-for-prusa-i3-mk3ss-for-use- If you want to attach the OLED Display with the display case from @wschadow (caribou3d)…
This Caribou cover is designed for the OLED display and an additional HyperPixel4.0 touchscreen. The Raspberry Pi is NOT mounted directly behind the display so that there are no visible power and USB cables on the control unit. I used a…
This is a 3030 Mount for the 7" MKS PanelDue, which doesn't fit the original PanelDue Cases due to the larger breakout board. It fits perfectly on the front of the Caribou Mk3s but should also fit other printers with 3030 profiles just…
Diese Montage nutze ich für ein TFT70-Display an einem 3030-Profil. Dieses Displaygehäuse nutze ich außerdem hierfür: Display Mount for BTT PI TFT70 von LoboThirteen | Kostenloses STL-Modell herunterladen | Printables.com
This is a special wrench I designed, to allow me to remove/install the latch in the caribou side cases, without needing to disassemble the latch mechanism itself. Can be manipulated by hand, but also has provision for a ¼" square drive,…
A cover to protect the circuit board under the PanelDue5i. Uses the same hardware typical to the Caribou construction. You need 1 cover and 2 brackets. Use m3 bolts to assemble the pieces, then bolt to the 3030 frame.
Full Image Catalog The complete gallery of my works can be found at www.marjers.com . You can search by the file’s reference number or simply click the preview image to open it directly. This is a high-quality 3D design optimized for…
The de Havilland Canada DHC-4 Caribou (In the USA military force know as the CV-2 or C-7 Caribou ) is a Canadian specialized cargo aircraft with STOL ( short take-off and landing ) capability .The Caribou was first flown in 1958 and…
Simple Caribou btt m8p case remix for mk3s. Freecad remix is a mess but its working.
Full Image Catalog The complete gallery of my works can be found at www.marjers.com . You can search by the file’s reference number or simply click the preview image to open it directly. This is a high-quality 3D design optimized for…
The de Havilland Canada DHC-4 Caribou (In the USA military force know as the CV-2 or C-7 Caribou ) is a Canadian specialized cargo aircraft with STOL ( short take-off and landing ) capability .The Caribou was first flown in 1958 and…
This is a remix of the Caribou3d Panel due 5i Cover. If you print the cover, you need support for the two mounts. You also need to print the brackets 4x - and longer screws(M6x30) to mount them! Thanks to Bernd for the test print :)…
This is my large filament spool holder for my Caribou 320 MK3S for 2 - 2,6kg spools. In V2 the srew hole is centered now. Print with at least 4 perimeters. PETG did it for me. An M3 threaded insert is required. You should print two of…
UPDATE: v3 had an issue with not enough space for M6 washer, v4 is corrected so it can now house a screw and a washer. Y-rod holder with cap for 3030 Caribou3d mod. This is a work in progress - a prototype. Uses 2x M6x14 screws with M6…
3030 USB Camera Mount (Caribou Frame) It's a simple little camera holder that mounts my USB camera to a Caribou Frame ( https://caribou3d.com/de/3-caribou-3d-drucker ). Printing The print does not need any support. I used PETG 0.2 to…
Bigtreetech Octopus Case for a Caribou 3030 Frame This is a case for a Octopus Board ( https://www.3djake.de/bigtreetech/octopus ) that fits on a Caribou Frame ( https://caribou3d.com/de/3-caribou-3d-drucker ). I converted this printer to…
3030 LED Circle Mount (Caribou Frame) It's a simple little LED Circle mount that lights up my printer and fits on a 3030 Caribou Frame ( https://caribou3d.com/de/3-caribou-3d-drucker ). Printing I printed this with organic support from…
This reverse bowden arm was designed for the Caribou 320 but will work on any 3030 T slot frame and should work on 2020 T slot as well. Uses a 12mm M6 bolt and T nut as well as a PCM-10 Pass through coupler.
LCD Cover for Oled Screen in multicolor. You can get the screen here: https://caribou3d.com/en/electronic-boards-displays/67-oled-display-20x4-white-black-by-ldo.html Remixed from original caribou parts.…
A great Wall Art of a Caribou. Do not forget to upload your makes, thanks ! Inspired by a sticker
I was bored so I made this. I dont know if it will fit so print it on own risk. I want input and info about the model if it works or what whould be better to change. it is ment to use a cable with a switch like on a lamp for to turn…
