Counting matching models…
These combs are designed to be zip-tied or hot-glued to wire shelf decking, I'm sure they will fit into other spaces as well. I'm hoping the flexure makes them work decently for cat5e as well. Design considerations/quirks The outer…
I made this cable clip to help manage an ethernet cable to my exterior cameras. It slides on to the bottom of common house sidings and holds snugly. opening is 10.5mm at the narrowest and 13mm at the widest. This should allow some play in…
A cable clip for a Cat6 cable with a diameter of 6mm in my case. The cable snaps into place and can be removed if needed. You'll need double-sided tape or nails/screws to secure it in place. Post-Printing After printing, you'll need to…
Original design by Greys which can be found HERE . General Info This is a cable comb/mount that can be used on wire shelving, server racks, walls, and more. The mounts can be used with either small zip ties or screws. If using zip ties or…
This is a remix of Greys' Flexture Cat6* Cable Comb , which allows using large 3M Command Strips for mounting. This is the version that can hold up to 12 cables. There is a 3MF Bambu Studio profile included, which has 4 of these set up on…
This is a wire comb I made for straightening out Cat6A cable before crimping. You put this on your index finger and then pull the wire between your thumb and the comb, along the grooves. It makes straightening out the wires way easier,…
I was trying to mount a keystone jack in a unique location using a typical single gang US electrical cover, and it was much too large to fit in the space. I recreated the mounting mechanism and put it on a small disc. It holds the jack…
These are highly modified skirts from the original Voron2.4r2 CAD drawings to incorporate honeycomb mesh behind the original hexagon skirt design. This mesh is created by utilizing the Slicer's capability to specify a part of an object to…
Mount a CAT6 cable splicing block. Printed without supports. You can use a M4 or a #8 screw to secure the block. I have to warn you that once the block is attached to the mount it is not easy to remove. I had to slide teasers under one…
There are 3 models included in the STL file. There is a straight and offset to allow for 90 degree runs horizontally and vertically and the final model is a blank label that can be used to clip on to the cables. This one is intended to be…
This is a remix of the model from Chris with the only difference that the magnet pockets are slightly reduced to fit 5x3mm magnets that I had already from a previous project.
I needed to convert my old patch panel that uses crimp termanials to RJ45 keystones (yes I hate working with termination, and this is just easier. And it uses the origional mounting screws. Please note - the edge bumps on the keystones…
I used mamut glue to mount. Use zip-ties to mount cable.
A straightforward wall-mounted clip designed to organize network cables neatly. It holds up to three Cat5e, Cat6, or similar cables, while the clip provides sufficient grip, a dedicated zip-tie channel is included for installations that…
Tool for untwisting and straightening twisted pairs in network cables. Simply insert the tool between a twisted pair and pull. If the wires need to be straighter, run them through the tool again and squeeze them straight. It is possible…
Hello i made this very simple but effective RJ45 keystone holder. this part can be implemented and mixed with other 3D designs that need a RJ45 connector to them. recommended to print with PLA and not with ABS. ABS is more prone to…
For pulling CAT5/6/7 cable snag-free through other mess of cables / drop-ceiling / raised floor Works when pulling just one cable out of a mess of cables, or when pulling a new cable through to replace a broken cable. Note: Always use…
Originally designed for a Startech.com 6U wall mount server rack. But should work with their entire line of wall mount server rack products. It's a two piece design. You can installed the CAT 6 terminated or unterminated it doesn't…
This is a keystone insert for a voron 2.4 front skirt, so that an ethernet connector can give easy access to the SPI port on the controller board or the Raspberry Pi inside the printer. This is to simplify connecting an ADXL345 when…
Printed in Aurarum PETG. .2mm layer height. Uses a 7GA screw to attach to building framework. Right size, impact driver, no hammer! Over tightening will cause it to split though.
Creates a cable comb to hold ethernet cable against 2020 extrusion. Designed for a Netgear 24/28 port switch.
Holders for neatly running Cat6 (6.5 mm diameter) network cables on IKEA Skadis pegboards. There are a few variants available: Horizontal for running cables horizontally Vertical for running cables vertically Vertical narrow, 11 mm c.t.c.…
I'm running some Cat6 outside for a camera, but I have fiber-cement siding (commonly known as HardiPlank) and couldn't staple the network wire. I noticed the siding planks had small gaps where they overlap, and upon further inspection,…
These combs are designed to be zip-tied or hot-glued to wire shelf decking, I'm sure they will fit into other spaces as well. I'm hoping the flexure makes them work decently for cat5e as well. Design considerations/quirks The outer…
Easily clip your LAN cables without need of securing them , all files to make your own remixes are in DWG , message me for Rhino files , you can change screw diameter , angles, or redesign it all if you wish (as long as you give me a…
