Counting matching models…
Tl;dr print this and put it around your SCH40 4" PVC sewer cleanout to protect it. Minimize impacts from lawn upkeep while making the target slightly bigger so that even as grass grows in you can still find the cleanout. Why? I ran over…
This escutcheon has two purposes. First, it is designed to make a plumbing cleanout wall access cap a little better looking; and second, it provides a wider diameter cover to hide possible wall damage or sloppy workmanship at the hole in…
I created this model to keep sawdust / drywall dust from falling down into my floor drains and drain tile. There are two versions of this model, one is a loose fit and the other is a press fit. You may need to trim the tabs on the press…
Simple Wrench for removing PVC Drain Cleanout caps. I used PETG for a stronger wrench. Layer Height :0.3mm Infill: 30% Infill Pattern: Triangles
Nothing special to this, just makes it easer to turn the drain cleanout cap. I used PETG.
This is a simple wrench for grabbing a square positive sewer cap. The wrench gives you a good place to grab the cap by hand. These caps are commonly used to close sewer cleanout access points and RV drain dump sites.
If you already have Yarbo's snow blower module, you'll find that the clean-out tool is also useful for clearing wet grass from the lawn mowing module. To attach this tool, the snow blower's hook design was replicated and installed in an…
This model was inspired by the drab, and pedestrian sewer cleanout offending my lawnscape. It was bold and brash statement in PVC offending the optic nerves of those walking by. It needed some care to maintain its performance functions…
This simple trip tray fits under the washer to catch water when opening the lint trap for cleaning. It has a spout that is set higher to maximize the amount of water the tray can hold.
When fastening it to the plug, be careful that you don't use a screw that's to long. Make sure it doesn't penetrate through the cleanout plug. The Screw cover prints best with support, you might have to trim a bit with a knife if you…
Offset adapter for French Drain Man Downspout Cleanout with Leaf Filter. My general contractor screwed up and a downspout was not properly aligned with a buried drain embedded in concrete. I designed and printed this adapter to mitigate…
I've got a 4 Inch PVC Cleanout Plug on another project of mine and I almost never have my Channel Lock Pliers nearby to open it with. So, I designed this Knob to fit over the square piece of the plug to make twisting it open easier…
This escutcheon has two purposes. First, it is designed to make a plumbing cleanout wall access cap a little better looking; and second, it provides a wider diameter cover to hide possible wall damage or sloppy workmanship at the hole in…
Quick easy print to replace the cleanout tool which comes with a new carpet shampoo machine and is inevitably lost by the first time it's needed. I printed mine in ABS which works really well with default slicer settings because it's so…
This is a chute that fits into the pellet hopper cleanout opening on a Pit Boss Pro Series 850 to make it easier to catch the pellets as they fall out. This may fit other Pit Boss models or even other brands. I have tested the design for…
I had an old, flush mount, slotted sewer cap (similar to below) that I needed to open. I couldn't easily open it with my existing tools, so I designed this hand tool as one of my first 3d prints I recommend printing with 100% fill
Cleanout wrench 4 inch designed by me. Useful when camping or RVing. PETG for strength, can use stronger plastics but unnecessary unless keeping outside 24/7. Then ASA would be good.
Unoptimized Cleanout Cap Must resize and look for dimensions before printing The head is very hard to work with, but screws perfectly with PTFE tape Printed on: Ender 3 v2 | PLA+ | 0.12mm | 20% infill | Brim
Fix for common toro snowblower chute cleanout tool. Printed in TPU since it's a part that's expected to flex constantly.
Tool for opening or closing a 4 in flush PVC cleanout cap. This tool has a handle attached to make hand operation possible. See PVC Flush Cleanout Cap Tool - Square for a similar tool with a Square top for use with a wrench.
Adapter for opening or closing a 4 in flush PVC cleanout cap. This adapter has a square top to interface with a wrench. See PVC Flush Cleanout Cap Tool - Handle for a similar tool with a handle top for use by hand.
I printed in PLA with 90% Tri-Hexagon infill, 3 walls. It feels strong enough, but I would not weaker than this.
I took the original model of this mainline cap and scaled it to fit a 3.5" basement drain. I only needed about half as many threads as the original model so I removed some. I also added a hose connector on the top because I needed a way…
For years I've been filling my smoker tube by holding directly to the hopper cleanout chute on my grill….but this always ended with spilled/wasted pellets. I designed this adapter to mount on my Camp Chef SG24 cleanout chute and funnel…
3x4 Downspout End with Cleanout and 9mm/3-8ths connector Remixed the 3x4 Downspout and merged to a 3d print file of a pill bottle. Scaled up, combined the spout end with pill bottle opening; combined the 3/8ths tube connector to the lid…
This stick has a hook at the end curved to help it fit in the main dust chamber of the Dyson v6 (and similarly shaped) vacuum cleaners. The curve helps it follow the round chamber, and it slots in some tight areas that I can't reach…
This covers the plumbing utility that gives access to the drain pipes. I believe it is a code to have access to this cleanout port but the port itself is not nice looking and is often located in plain view. The cover base fixes to the…
