P
PrintablesZurrie
Cupholder fits Mercedes CLS350
Print with ABS/ASA/PETG for hot-car resistance. The fit is about half a millimeter undersized. Cup-diameter set to 70mm
- Downloads
- 305
- Likes
- 26
- Rating
- 0
Search results: cls
Counting matching models…
P
Printablesmoreco
Garmin Varia mount for Canyon VCLS 2.0 seat post
Minimalist Garmin Varia seat post mount for Canyon VCLS 2.0 seat post, which comes on some models of the Grail, Grizl or Endurace bikes Ideally printed in ABS or another not-too-stiff material Mounting requires either removal of the seat…
- Downloads
- 239
- Likes
- 21
- Rating
- 0
P
PrintablesDakoriki
Bass Shaker for Fanatec CLS Elite Pedals
I used M3x30mm countersunk bolts for mounting. Slightly shorter screws might work. I used 30mm long screws because that was what I had on hand at the time. The pedal is a bit top heavy with this and I had to add a tiny deadzone to the…
- Downloads
- 111
- Likes
- 16
- Rating
- 0
P
PrintablesPixelChroniclesMiniatures
Pokemon inspired, Naclstack, Tabletop DnD miniature
IF YOU LIKE THIS MODEL, CHECK OUT MY OTHER MODELS AND SUPPORT MY PAGE Patreon at https://www.patreon.com/pixelchronicles ! Pokemon inspired, Naclstack , Tabletop DnD miniature 25 mm medium base which can be used for DnD and other Tabletops.
- Downloads
- 101
- Likes
- 18
- Rating
- 0
P
PrintablesCretzu' Andrei
120 mm fan for MeanWell LRS-350 / Creality CLS49-350-24 Power Supply (Creality K1C)
I've replaced the stock CLS49-350-24 power supply from my Creality K1C because it was very loud. The swap with MeanWell LRS-350-24 is very simple because the Creality power supply it's a clone of LRS-350. After replacing with LRS-350-24,…
- Downloads
- 98
- Likes
- 23
- Rating
- 0
P
PrintablesFusilier
Thread Spool Stand for Chinese Leather Shoe Patcher (CLSP)
This tread stand replaces the little rod on the CLSP for holding your tread spools. The stand is assembled with superglue and once installed (you'll need a suitable bolt and a couple of nuts) it also feeds the thread from a proper height.…
- Downloads
- 96
- Likes
- 22
- Rating
- 0
P
PrintablesReedTiger
SIMHub dashboard for Moza R5, R9, R12 and Fanatec CLS DD (may be others)
I DID THIS JUST FOR MYSELF AND FOR A FRIEND, ACTUALLY I DIDN'T REALLY WANT TO SHARE IT, SO I APOLOGIZE FOR ANY FLAWS. In order for the face to be transparent, but at the same time darkened, it must be printed from transparent plastic with…
- Downloads
- 78
- Likes
- 46
- Rating
- 5
P
Printablesdachnlk
Creality K1SE - PSU cooling fan mod (CLS49-350-24)
Use 92x92 fan for this upgrade
- Downloads
- 70
- Likes
- 26
- Rating
- 5
P
PrintablesGuillaume
thread guide for chinese leather shoe patcher (CLSP)
this gadget guide the thread from the bobin holder of the CLSP. with it you can lay the bobin whatever its size on the table.
- Downloads
- 66
- Likes
- 13
- Rating
- 0
P
PrintablesAsus1357
Lack enclsure 10mm with cover led strips
I had modified the strips to accommodate my 10mm led strips (with silicone cover). I was asked if I would post those changes. filament petg or better (temp tolerance) uploaded working copy. corrected,
- Downloads
- 50
- Likes
- 5
- Rating
- 0
P
Printablesdwbmb
Fanatec CLS Pedals brake pad
The whole shape is beefier and wedged to eliminate the need of additional angle backs, thus making the whole pedal stiffer. I printed mine with PC-CF cause I already had it loaded in my printer but any strong filament should do.
- Downloads
- 37
- Likes
- 5
- Rating
- 0
P
PrintablesDerik Whittaker
Single PSU Mount for Electronics Enclsoure
Simple to print Single PSU Mounts for securing a PSU to an enclosure. You will want to print the file 2x for a full setup This design is generic, will fit any PSU with 150mm spacing between the mounts. Mounts using M4 bolts. Print…
- Downloads
- 33
- Likes
- 3
- Rating
- 0
P
PrintablesMIC1980
Hexagonale Enclosre Verkleidung // Hexagonal Enclsore casing
Ich habe mich hier an der Verkleidung eines DIY Enclosures versucht. Hierbei habe ich mich an der Optik des Hexagonal (Honeycomb) wall von fymetool orientiert. Allerdings habe ich keine Dateien von ihm verwendet sondern alles selber in…
- Downloads
- 33
- Likes
- 7
- Rating
- 0
P
Printablescsweichel
Honeycomb Rail for the Original PRUSA Enclsoure (OPE)
This is a set of honeycomb plates for the lower right edge of the Original PRUSA Enclosure. Prints on one plate.
- Downloads
- 32
- Likes
- 9
- Rating
- 0
P
PrintablesNiels Peter Andersen
Shimano internal battery holder for Canyon VCLS seat post
For mounting Shimano BT-DN110 (or similar) internal batteries inside Canyon VCLS seatpost. Category: Sport & Outdoors
- Downloads
- 17
- Likes
- 3
- Rating
- 0
P
PrintablesBurningToast
Naclstack (Pokemon Scarlet/Violet)
A low quality model of Naclstack from pokemon scarlet/violet (Watermark Included)
- Downloads
- 16
- Likes
- 3
- Rating
- 0
P
PrintablesAdrian Lignowski
Brunner CLS-E MK1 Yoke Clamp Adapter
This is adapter for Clamp Mounting to the Brunner Yoke CLS-E MK I
- Downloads
- 10
- Likes
- 0
- Rating
- 0
P
PrintablesLauserich
Canyon S15 VCLS 2.0 CF Varia Seatpost Mount
Mount Your Varia neatly to Your S15 Seatpost. You need to take out your seatpost to mount it but then it can stay there forever. Printed in PETG-CF, but I think ASA is a better Choice! Needs: - 2x M3x4x5 Heatset inserts - 2x M3x14 or 16…
- Downloads
- 10
- Likes
- 3
- Rating
- 0
P
PrintablesCitruspers
Top Hat for CLS Colour PAR 12
Use at your own risk. I printed this in HIPS for its superior temperature-resistance compared to PLA.
- Downloads
- 8
- Likes
- 1
- Rating
- 0
P
PrintablesTheRadRomulan
Dig-Quad WLED Enclsoure
Features: Wife approval factor... many options I found didn't look good enough for the significant other to let it in the living room. This is more discrete. High voltage wiring is fully enclosed in separate section of the enclosure, thus…
- Downloads
- 5
- Likes
- 1
- Rating
- 0
P
Printables
Dig-Quad WLED Enclsoure
Features: Wife approval factor... many options I found didn't look good enough for the significant other to let it in the living room. This is more discrete. High voltage wiring is fully enclosed in separate section of the enclosure, thus…
P
Printables
VCLS 2.0 Dirt Protector
After having severe sounds that originate from my VCLS 2.0 seatpost, I've noticed how much dirt has collected between the leaf springs. Many of those particles come from mud that is collected on the bottom side of the saddle and then just…
P
Printables
CLS camping light shade
CLS camping light shade you still need a UNC 1/4"-20 screw to fix the lamp