Counting matching models…
A symmetric and rounded Tribahtinov mask for the Celestron 925 Edge HD. Based on the Satakagi Tribahtinov web calculator. Also included M3 knobs as a replacement for the original screws.…
Yet another Gotek mounting plate for the AMSTRAD CPC 6128. This is a mash-up of different version found on Thingiverse. Thanks especially to fdivitto thing:2876318 and briefer thing:4603742 for their model. Make some modification to have…
A Gotek USB Floppy Emulator Caddy that fits systems that have an internal 3 inch disk drive such as the ZX Spectrum +3 and Amstrad CPC6128, 664 & the external drive enclosure FD-1. The front plate has holes for the standard gotek board…
If you have a Celestron CPC11 telescope with a Hyperstar installed then you likely want something to hold your camera cables. Attaching the cables to these guides means the diffraction pattern seen in your camera images will be…
version for 45 degrees Category: Computer
Key set for AMSTRAD CPC464 cassette player Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.12 / 0.14 Infill: 25% Filament: Generic PLA Notes: user support for key lever printing Category:…
This is a remix from the original by fdivitto. The modifications are: The braces are longer in order to be able to attach an additional screw inside the case, and also the other black screw from the right of the CPC case (the original…
This is a simple stand designed to hold an Amstrad CPC 464 computer in a vertical position on a shelf, table, or similar surface. Print two in your choice of filament (PLA is perfectly strong!) and you're good to go. I added some thin…
This allows the Amstrad to be placed on the original monitor. There is a model for the CPC464 and a model for the CPC6128.
It's possible to bypass the built-in floppy disk drive by connecting a standard 3½-inch drive to you Amstrad. Hurray, your CPC is now prepared for the future ! With CPCDiskXP, you will be able to write and read Amstrad CPC disks (.dsk)…
Same thing as HERE but for the CPC6128 PLUS Print Settings Printer: Creativity Elf Core XY Rafts: No Supports: Yes Resolution: 0.12/0.14 Infill: 15/20% Filament: Generic PLA Category: Computer
4x 3mm nails of 20mm length for clips 2x springs for clips - we used default springs from ender3 heatbed (20mm length, 8mm diameter, 0,9mm wire) 4x 14mm M3 screws 4x M3 nuts 15mmx0,3mm copper grounding tape for contacts 2x 150mm copper…
I created THREE different chip racks to fit CPC (classicpokerchip.com) custom 44mm chips. A. 5x20 = 100 chips, stacks on itself full of chips B. 4x25 = 100 chips, stacks on itself full of chips C. 4x20 on 39mm = 80 chips, stacks on…
MP-like box for Amstrad CPC 464/664/6128. Featuring SCART-to-HDMI converter and 5V power supply. In order to build one you will need : Soldering iron + basic soldering/desoldering skills Female IEC plug Scart-to-HDMI converter. The very…
I am using the Celestron-brand dew heater ring on my CPC 9.25" telescope but did not want to spend ridiculous $$$ on their heater controller when this $80 dumb controller works just fine. Mounting it to the scope's round barrel when it…
Sometimes the HIWIN lienar rails are hardly to order. So i decided to order CPC linear rails. The CPC linear guideway block is roundabout 1,5 mm longer than the HIWIN linear guideway block. This upgrade is for the original PRUSA MK3S+…
Amstrad CPC floppy and printer interface dust covers
Dies ist ein Remix von McPcholkin. Die ganze Anerkennung geht bitte an Ihn. Vielen Dank dafür. Es werden zwei runde Neodym Magnete: 8mm x 8mm x 1mm benötigt. Original: https://www.thingiverse.com/thing:3652881 Ich habe die 3mf Datei vom…
I bought a RiscPC slice from eBay that was an absolute bargain, it was however missing the spring from the right hand side of the flap and on the left hand side the clip that retains the flap was missing. I fixed the missing sprint with a…
Simple keyboard dust cover/cap for the Amstrad CPC 6128. Based on my Sinclair Spectrum dust covers. I also added a repo of the RGB stripes for those with a multi-colour printer. Just add the stripes to the model in the slicer. This…
This is an adapter for the Gotek USB floppy emulator that can be used in the Amstrad CPC 664. It can be used with an alternative firmware to read directly DSK images: https://github.com/keirf/FlashFloppy You will find the STL file…
This is a case for the M4 WiFi module (v2 - the larger one) for Amstrad CPC by Duke at Spinpoint.org . I started with the version from povvercrazy, as it had much better screw support (the original failed on me). I also added a support…
I saw they sell replacements for $5 and I almost threw mine away when I opened my OOLER, so I figured I'd model this up in case anyone needs a replacement. The bridges are short and the inside has a chamfer so this will print fine without…
These switches where handed out for free in Australia (they can still be purchased). They basically turn off a power board when your computer is turned off allowing monitors, printers, speakers and so on to be turned off. I made this by…
Secretly a 4th spacecraft, the owner registered it as a Custom Personal Cargo Transport, or CPCT-1, nicknamed the "Vulcan"
Simple keyboard dust cover/cap for the Amstrad CPC 6128. Based on my Sinclair Spectrum dust covers. I also added a repo of the RGB stripes for those with a multi-colour printer. Just add the stripes to the model in the slicer. This…
Secretly a 4th spacecraft, the owner registered it as a Custom Personal Cargo Transport, or CPCT-1, nicknamed the "Vulcan"
This is a Remix of Zach Freedman's Gridfinity divider bin template. It fits up to twenty five MCPCB's used in flashlights. It's ⅔ of a unit high and is stackable. Version A has nineteen 20mm slots down the center and six 16mm slots down…
