Search results: dc18sd

Sort order

Counting matching models…

P
PrintablesD4rk Helmet

Makita DC18SD mountingbracket

Small brackets to mount a Makita DC18SD charger to a wall. Do this one by one for each mountingbracket remove the rubber You need to remove the original case screws put the bracket replace the original screw with a 4mm x 50mm countersunk…

Downloads
104
Likes
13
Rating
0
P
PrintablesNelsonClark

Makita charger flat wall mount for DC18RC, DC18SD, DC18SH

A simple flat mount for the most common Makita chargers on the market, no need to try and line things up like with the single foot models or like the dual tilted ones. This model is easy to print and easy to use. To install charger, screw…

Downloads
1,228
Likes
97
Rating
4.9
P
Printablespoprhythm

Makita Battery Charger DC18SD Mount - Pegboard and Wall

The DC18SD is slightly smaller than the DC18RC, so this adaptation will fit this model. Insert the top peg at an angle first, and then push in the bottom two support pegs. You may want to add a screw into the pegboard for extra support.…

Downloads
321
Likes
35
Rating
4.75
P
PrintablesJXC

Makita DC18SD Wall Mount

Flush mounting for Makita DC18SD charger. One of the sides has pin holes that are not straight up and down, so I decided to cant the screwholes relative to the mount, so you end up with the smallest possible mount, but also have vertical…

Downloads
320
Likes
38
Rating
0

Skadis T-Nut Mount for Makita DC18SD

This model does not fit DC18RC Pull out rubber feet from the bottom of the charger and mount brackets into holes. To mount brackets you'll need both T-Nuts and alignment guides, which you can find here:…

Downloads
148
Likes
23
Rating
5
P
PrintablesR B

Makita DC18SD wall mount

Makita charger DC18SD wall mount.

Downloads
148
Likes
9
Rating
5
P
PrintablesRasmus

Makita charger mount for DC18SD charger

Holder for Makita DC18SD charger. mounts with 4 screws. the charger can be taken on and off without tools.

Downloads
124
Likes
10
Rating
5
P
PrintablesMenga

Wallmount for Makita DC18SD Charger

Print on the side. Support for the pins are a must, for the holes it isn't necessary. The holes for the anchor screws are 3.7mm, meant for 6mm Fischer wall plugs (Drywall or brick)

Downloads
91
Likes
2
Rating
5
P
PrintablesLannix Design

Makita Battery Charger Mounts (DC18SD & DC18RC)

Wall mount brackets for the Makita single battery slow charger [DC18SD] and the quick charger [DC18RC]. Each mount is in two parts and there is a slight difference between the slow and quick chargers. Each mount needs five wood screws to…

Downloads
69
Likes
4
Rating
0
P
Printablesboddys

Makita DC18SD Charger Mount

I am not sure if Makita changed the design on these DC18SD chargers but when I was looking for a mount, the hole layout that people had used did account for the offset of the top pin, so I designed my own. I can confirm that this does NOT…

Downloads
55
Likes
6
Rating
0
P
PrintablesMksutov

Makita DC18SD Charger Honeycomb Storage Wall Screw Mount

I did not get lazy, I swear, the top-right mount is supposed to be 90 degrees rotated, as below. It locks the charger in place, so if you pull your battery out without locking the charger in place with your other hand, the charger won't…

Downloads
19
Likes
4
Rating
0
P
Printables

Makita DC18SD Charger Honeycomb Storage Wall Screw Mount

I did not get lazy, I swear, the top-right mount is supposed to be 90 degrees rotated, as below. It locks the charger in place, so if you pull your battery out without locking the charger in place with your other hand, the charger won't…

P
Printables

Makita charger flat wall mount for DC18RC, DC18SD, DC18SH

A simple flat mount for the most common Makita chargers on the market, no need to try and line things up like with the single foot models or like the dual tilted ones. This model is easy to print and easy to use. To install charger, screw…