Counting matching models…
A replacement battery cover for Denon RC-1192 remote. Printed in PLA, but I think that PETg or ABS will be good too. Print instructions Print Settings Rafts: No Supports: Yes Resolution: 0.2 Infill: 100% Filament: Any PLA
This is a replacement battery cover for Denon Remotes, mine is printed in jet black ASA from Polymaker. Print as oriented and ensure supports are enabled , only needed for the clip portion. The bottom tabs do not need supports. Confirmed…
Includes 3x regular faders 2 x tempo faders Custom Fader Kit 5 Pack for Denon DJ PRIME GO - Personalize your controller with custom faders
The knob should fit just about perfect on the shaft if the measurements match. You can find shaft hole specs in the pictures. The diameter is 47.3mm. I found the settings in the project file to have the optimal settings for PLA including…
This object was made in Tinkercad. Edit it online https://www.tinkercad.com/things/2Ce1oPrpMBB The feet on my Denon stereo receiver stuck to the painted shelf it was sitting on. I went to move the receiver and the center of each foot…
Die Klappe deines Denon Receivers hängt schief, weil das rechte Scharnier sich gedacht hat "Haha, ich breche jetzt einfach mal!"? Du bekommst kein Ersatzscharnier, weil es seit vielen Jahren ausverkauft ist? Dann hast du hier jetzt Glück.…
Since the denon support doesnt provide this piece of plastic i had to remodell them Same model for both buttons
Denon AVR Riser that raises the height of the audio receiver amplifier to enhance cooling. Works from AVR-990/3310 to AVR-X3800H and others. I noticed the AVR-X3800H now have a fan on the bottom of the chassis. Therefore on carpet it is…
An saucer for the Soundswitch Control One, so that it is at the absolutely same high as the Denon DJ Prime 4
This should print and have a good fitting. I printed at .2mm layer height on my printrbot Metal Plus
Table holder for Denon remote RC-1181 Print Settings Printer: Anycubic i3 Mega Rafts: Doesn't Matter Supports: No Resolution: 0,2 Infill: 20% Category: Audio
No more backstrain from leaning over for hours on end during a busy set. I decided to slice it in two and add mounting brackets so it could fit my printer. You will need 8 m4x10 screws for the brackets. Holes tap themselves! Can…
Summary: I designed this mod since I wanted to be able to replace the cable on my Denon D2000 and D5000 but didn't want to permanently modify the frame, baffle or driver. This would allow me to go back to the stock cable is so desired.…
This was the first 3D model I created and terribly basic yet incredibly useful to me. I had purchased a Denon AVR-S760H receiver and found it was just a bit too tall for my entertainment center in order to have sufficient ventilation…
My Denon turntable foot was missing. I replicated the part using another foot as the model to measure and replicate. The part is no longer available. I initially made one in PET-G and it worked but to get the dampening that was made with…
Brackets for Denon soundbar mounting under hanged Phillips TV
I printed it with a layer thickness of 0.2. Used PLA Printed with Sidewinder x1 Printed once, tested and works I don't know whether the button also fits on other models
This is a quick adapter I made that lets you use the Denon AVR cardboard mic Stand for the UMIK-1. The finished print should fit the UMIK-1 snugly, but not too tight. Scale down or up 1% to desired tightness. This can be made with either…
Designed this to replace the missing volume knob on a Denon DR-M07 tape deck. Printed in PETG and dropped it on top of the potentiometer, job done. Could be finished with bondo then primed and painted for a better look.
Replacement part for the Denon DP-45f turntable button(A) assembly. Part number 1138161302. I made this after the power button broke from stress on the plastic. I recommend printing in the orientation of the file for the strength of the…
# Denon DP-900M / Pioneer PL-PM2000 - Dust Cover Hinges Replacement hinges for turntable dust covers. The original plastic hinges are known to break after 25+ years of use. Why This Model? - Many of these used turntables are sold with…
Designed these to provide better air flow under the unit located on carpet as well as protect the buttons from the Roomba. Printed at 20% infill, Overture PLA on the Prusa mini.
I created a support for my Denon RC-871 touchscreen remote control, this remote control equips the Denon AVC-A1SE amplifier, Printer= Elegoo neptune 2S Filament = PLA+ , Sunlu Black + White Infill = 20% Rafts: Yes Supports: Yes
My daughter very like push every buttons. This guard can protect power button on my Denon receiver. Optimized for 0,12mm layer
I’ve occasionally driven my amplifier into protection mode when playing at very high volume levels with low-impedance speakers (down to 3 Ω) at full range. This usually happens during longer listening sessions, as the amplifier tends to…
This is a replacement tonearm lift cam for a Denon DP-62L turntable. The original is a nylon part with a brass insert. This part is printed in PLA+ with an M3 nut and M3 X 6mm screw. You may need to flatten the end of the screw to keep…
My battery cover was missing, so I made my own in Catia V5 and printed on the side in PETG. Works great and snaps in place like the original.
Tested on Denon AH-D2000 HiFi Headphones. Created to replace broken driver assembly / mount 3rd party driver into AH-D2000 housing. I know Denon is using a lot of Fostex parts, so it might work with Fostex headphones too. Careful with the…
I needed to replace the power cable on my Denon DP-35F turntable. The old cable ended up being a little smaller than the replacement. So I designed a new cable clamp to prevent the power cable from being pulled out and damaging the…
For those Denon fans, here is a sign you can proudly hang on your wall. The photo is printed at X=11cm so quite little, yet the STL is large so you can print it any size you like. If you make a print, please post a copy as I would like to…
Hi everyone, the next model is a CD tray front cover for the UD-M3. Test it :-))) Have a nice day Donate : Paypal [email protected]
# Denon DP-900M / Pioneer PL-PM2000 - Dust Cover Hinges Replacement hinges for turntable dust covers. The original plastic hinges are known to break after 25+ years of use. Why This Model? - Many of these used turntables are sold with…
No more backstrain from leaning over for hours on end during a busy set. I decided to slice it in two and add mounting brackets so it could fit my printer. You will need 8 m4x10 screws for the brackets. Holes tap themselves! Can…
il faudra une vis comme celle-ci https://www.amazon.fr/gp/product/B073MJ1L31/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1 et un vis de 4X16 mm n'oubliez pas de poster vos photos de vos prints ça fait toujours plaisir !
This is a replacement tonearm lift cam for a Denon DP-62L turntable. The original is a nylon part with a brass insert. This part is printed in PLA+ with an M3 nut and M3 X 6mm screw. You may need to flatten the end of the screw to keep…
A keychain with the Engine DJ logo. Attach this keychain to your DJ USB drives.
3D printable topographic miniature of Pordenone - 🇮🇹 Italy Capture the beauty of Pordenone 's city landscape with this topographic miniature! This 3D model represents the geographic area around the geo coordinates 45.956, 12.660 (LatLng)…
I built this model for two reasons, first I wanted to declutter my desk and try to hide as many cables as I could and seI built this model for two reasons, first I wanted to declutter my desk and try to hide as many cables as I could and…
The clip broke on our Denon Reciever remote's battery compartment. In the past I would have thrown some scotch tape over it, but now you can print a replacement! I would recommend printing this on its side using supports so the clip…
Turntable isolation foot for a Denon DP-1200, using a squash ball. M6x1.0 hex head bolt insert, groove for screw head in turntable base. Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: No Resolution: 0.2 Infill:…
Simple 3D printable part, useful for replacing a lost or damaged button. This download includes 2 files : one with the original button dimensions, and another with small adjustments I made to get a perfect fit on my Prusa Core One L , in…
Element holding headphone - fits rigth and left side. It is not perfect but it works just fine if you happen to break your headphones. Feel free to remix. Skechup file included! Print Settings Printer: Anet A6 Rafts: Yes Supports: Yes…
A real tiny part... for an denon drr-m10 tape deck.... printed on the prusa mini with an 0.25mm nozzle. Verry tiny part… its the part i point at with my tweezers, i printed it in pla but i think its gonna be better in an resin printer.
I created a template for holding remotes and attaching the holder to a RÅSKOG trolley. The system is made to be modular and needs 4x12mm magnets.
There are plenty of replacement bodies for the Denon DL103 and DL103R, that require stripping of the cartridge. This cap can simply be put over the cartridge to reduce resonances of the side walls of the original body. I wanted to test…
This has been a long time coming. While I love my Denon D1100's that I bought many years ago in Japan, the one thing that I always noted was how weak the build quality was of the plastic hinges, and my pair has broken in many ways and…
il faudra une vis comme celle-ci https://www.amazon.fr/gp/product/B073MJ1L31/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1 et un vis de 4X16 mm n'oubliez pas de poster vos photos de vos prints ça fait toujours plaisir !
