Counting matching models…
These are some short feet for a Rigol DS1054z (or any, I'm guessing, in the 1054 family). I had been using some taller feet that were great, but the extra height got in the way of my tool storage wall behind it. These slip on easily over…
There is little for the Uniden SDS100 on this site, so I uploaded this stand/holder under the creative commons license with attribution going to Todd Meyer that goes by the online name TwIzTuD. Included below is a photo of my make.
This is an adapter for putting a 60 mm fan into your trusty Rigol DS1054Z oscilloscope inspired by https://www.prusaprinters.org/prints/10300-rigol-ds1054z-converter-for-60mm-fans . I'm using a Noctua NF-A6x25 FLX with their low noise…
Printed in PETG Printed on its Side Uses #4 Screws to mount
Stand to hold a Uniden SDS100 Scanner upright, tilted back 15 degrees to aid in reading the display.
This is a simple drop in 20mm ball mount for the Uniden SDS100 Scanner. I needed something to use with the 20mm Bulletpoint Mounting Solutions system. This mount can be left in the vehicle while the device itself can be pulled in and out…
This model comes from a scanner enthusiast (like myself) that goes by the name jbix1958 online. It's to protect the contacts of the battery and to afford it a modicum of protection from potential crushing.
This thing allows you to mount a 60mm fan inside the DS1054Z. I used a Noiseblocker PR-2. Now it is silent. One edge needs to be removed. Otherwise the fan pushes against a pin header on the main PCB. Print instructions Category:…
Replacement foot for Rigol DS1000Z series oscilloscopes (ds1054z, ds1074z, ds1104z). The angles, dimensions and the flappy action are similar enough to the original feet, so you can just replace one of them. I also used a 2mm steel axle…
Simple probe holder for 2 probes (DS1052) just glue to the side of your scope This probably won't work if you still have the yellow tips at the end of the probes, you will need to modify it to make holes bigger
These are probe holders for Rigol RM-DS1000Z rack kit. 4x M4x12 or M4x14 countersunk screws are needed for mounting. Designed for RP2200 probes.
The signal generator is a useful tool for the electronics enthusiast's work bench. You can spend a lot of money for a powerful signal generator. The UDS1000S series of signal generators are feature rich and low cost. The module is readily…
I was struggling finding an appropriate spot near my couch for my portable scanner. I designed this up in fusion for the radio and other storage for a can. Could probably scale up 1% for a little more room as the fitment with the radio is…
When you use the retractable feet to tilt the instrument, the oscilloscope tends to slip or the feet collapse. With this model, you have the same angle as with the retractable feet, while the entire instrument is stable. You can also…
Rigol DS1054Z scope wall mount Remix of Rigol DS1xx4Z scope wall mount bracket" by Masterkookus thinner less material reduced print time Print Settings Printer: Multec Multirap 420 2Move Rafts: No Supports: No Resolution: 0.2 Infill: 25…
On the back of my electronics workbench I have a couple of IKEA Skadis board to mount my tools to. These are the brackets I used to mount my Rigol DS1054Z oscilloscope. Note that these brackets are actually a mirror of each other. It is…
Replacement in case you break the tab off like I did Designed for: https://shop.homeseer.com/products/z-wave-door-window-sensor HomeSeer HS-DS100+ Z-Wave Door / Window Sensor
I wanted to place the SDS100 closer to a window, for improved reception. This is a two piece build to minimize supports. I placed a piece of double-stick tape on the sill plate to secure the holder to the sill.
This is a remix of Devon Goldstone's Rigol DS1104 wall mount brackets. See the attached quick&dirty OpenSCAD file, if you dare ;)
Hi, this is a commissioned model for my workmates from our electronics testing department. A nice case for their JTAG programmer pcb (OLIMEX TMS320-XDS100 v3+ JTAG Programmer). It is a two part case for use with 8x M3 inserts. The input…
Stand Base for Uniden SDS100 I printed mine with black PLA+ , 0.4mm nozzle, 0.2mm layer height and 10% infill. No support needed. 2026.08.05 updated step file and some users reporting it was corrupt This is designed for the High Capacity…
Original model: OLIMEX XDS100V3 Case - by: x3on I've made some changes which i found helpful, see the differences to the original model.
DS1054z to 2020/vesa adapter Basically that, its very tight, you may need to reduce the "back tooth" a tad, you may not (it fit for me but very tight) I had originally made the little back tooth to allow for more rigid mounting by ramming…
Kilckfast connector for Uniden SDS100
remixed to hold a lipo battery. Thanks Yanick Deguise for sharing the files! Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Infill: 25 Filament: 123-3d PLA white Category: Parts
knob for the Uniden SDS100 handheld scanner.
Stand to hold a Uniden SDS100 Scanner upright, tilted back 15 degrees to aid in reading the display.
Original model: OLIMEX XDS100V3 Case - by: x3on I've made some changes which i found helpful, see the differences to the original model.
This is a stand for the Rigol DS1052E which is a snug fit to the base which lifts it off your desk and adds storage underneath it. This is a large print and will not fit on normal sized printers, e.g. MK4S/Bambu printers. It fits on a…
