Counting matching models…
I really don't like dust flying around my garage, routing edges was always one of the worst offenders. This shroud, combined with the standard dust collection port for DeWalt trim routers, will nearly eliminate stray dust from edge…
Li-Ion case for MAKITA 8391DWPE PA18 18V Drill Inspired by Erhil's design for the 14.4v Makita Power pack I decided to make an 18v (PA18) version. Replaces the crappy NiCad batteries. This was designed to fit non-protected Li-ion…
MAKITA 8391DWPE PA18 18V Drill to LXT Adaptor After many, many revisions I've finally got a version that I'm happy with. This will allow you to use the newer LXT (Li-ion) batteries with an older PA18 (Ni-Cd) Makita drill. I used a cheap…
This is a remix of the MPCNC quick release router mount to provide a slightly modular place to mount accessories. Print instructions Fed the original through netfabb to fix geometry issues. Removed the actual frame mount in the rear to…
I modeled the baseplate so I could use a jig setup by screwing a 1x3 board and route a radius. There are 2 stls, a stock baseplate, and a modified baseplate. I also include the Blend file if you want to modify further. Category: Machine…
Collection of failed and successful pen holders attached to my my Dewalt DWP611. Print instructions A collection of pen holders I've tried attached to a Dewalt DWP611 (see parent project for mount). This is a work in progress Currently,…
A two part variation of the original model, with additional drip tray and drainage holes, interlocking with a twist lock.
A recreation of the more “exclusive” GEN2 Decor - Faceplate
Dust Shoe for my CNC Router with a DWP611. Fits a Ridgid shop vac hose. Assembly of the top requires 2 long 5mm socket cap screws and 5mm nylock nuts. I measured and cut down 90mm cap screws with a hacksaw to roughly 77mm so that they…
This is a simple model that can be mounted onto the DeWalt router. I have included holes for 6 to 18" holes. The name should not be changed. I am offering this model for personal use only. The orange jig pictured here is the first one I…
Adapter fits hose and dust shoe fairly tight, might want to reduce scale slightly. First print worked well enough for the task that I didn't feel the need to print another. Printed in PETG for my first piece.
Simple hand wrenches for the Dewalt 660, 611 and Bosch PR20EVS routers works well with 2.5 inch endmills and v bits. The tip of the tool needs to be smaller than the nut. **Dec 2, 2020 updated fit and added .25 inch bit shank holder.…
This mounting plate lets you use a Dewalt DWP611 router with a Craftsman 25444 router table. The mounting plate is 1/4 inch thick. Same as the base plate that comes with the router. To mount the plate to the router table I used M4-20…
Modern planter set top layers to 0 and wall layers at least 3 need to scale to your needs !!!! follow and like !!!!
Small angle bracket to hold a roughly 8mm diameter point. Print instructions This is designed to help measure travel distance on the X and Y axis when setting up and tuning a CNC router. Uses 1 m3x8 screw to hold the pointer in (a nail),…
GEN2 Decor Handles - Adjusted for 12mm screws instead of the default 16mm and a bit ‘more chamfered’ for esthetics.
This is a laser mount that uses the existing and stock Dewalt DWP611 router mount and a JPhotonics 7watt laser with spindle mount hardware (1/4" shaft). The only hardware required is single M5 25mm screw. This works for the Lowrider CNC…
a 96 wellplate stand, to pipette in a healthier position and to print it without support
This was created to replace the stock spindle mount and upgrade the “spindle” to a dwp611 router. Save the linear slide bearings and plastic worm drive gear of the stock part to reuse them as i designed this to work with all existing…
I made an adapter for the DeWalt DWP611 router to fit an 80mm spindle mount. This is designed to be flush-mounted in the Sienci Altmill MK2 80mm spindle mount. This part features an offset mounting configuration that allows more space for…
we have a test where we transfer one phase from an 2,2mL dwp in an 1,2mL dwp. In our case with a 8-channel pipette.
This is a simple model that can be mounted onto the DeWalt router. I have included holes for 6 to 18" holes. The name should not be changed. I am offering this model for personal use only. The orange jig pictured here is the first one I…
A Stand designed for the D-Link DWP-1010 5G/LTE unit to let it stand on a flat surface. Added hole for putting RJ45 cable through. You need to take off both the light blue arm and the cover with the flat cable gland. You can use the six…
As I was building my Onefinity CNC machine, I realized that I didn't want to use the recommended Makita router for a number of reasons: Brushed motor No LED lighting User reliability reports However, the DeWalt router that I wanted to use…
