107 models
Intro A super-simple 3D-printed cleaning tool designed specifically for earbuds and in-ear headphones . It removes accumulated earwax and debris quickly and safely, helping restore sound quality and hygiene — all with a very short print…
Intro Earbuds Cleaning Tool V2 is a small, easy-to-print earwax remover tool for in-ear headphones and earbuds . It helps you safely remove earwax, dust and debris from your earbuds without damaging the speaker mesh . The first version…
Enjoyed this model? Support me at buymeacoffee.com/fifindr to keep the designs coming! Say goodbye to dirty earbuds with the Earbuds Cleaner Tool ! This dual-sided design features a brush-like surface on one end for removing earwax and…
A remix of the Lightning connector based version from @stripetuning_193054 to accept the new USB-C connector.
Finally do sports without worrying for your earbuds falling. Printed on PETG, about 15 minutes print. Make sure to reflect the model on the X axis horizontally so you can print each side. They snap from the outside into position. For more…
It gets pretty hard getting the earwax out of your earbuds some times and it would be nice if there was a tool for doing it. Well worry no more because here it is! This earbud cleaning tool is super easy to print, and it takes only a few…
if for some reason the control panel doesn't line up correctly you can cut a small bit off the bottom and sand it flat. i will be editing this in the future
A remix of the USB-C connector based version from @ChrisBoorman_136327.
My initial design caused too much echoing, so here is a version that seems to give a slight white noise effect at first, then just dampening. There are two versions, the first model has a short stem to the fitted earbud. The second has a…
About This gridfinity holder is designed for the earbuds case of the QCY MeloBuds Pro. Print instructions Based on one print run: PLA, 0.2 mm, no support.
Finally a proper 1x2x9 Gridfinity storage for your Redmi Active 4 case! Should work with any pebble like case no larger than 64x25x54mm although the fit may not be as snug. Also with the remaining space, pencil holders with an extra tip…
Description I made these TPU earbud/earphone running fins/wings so they would not fall out of my ears anymore and I am very pleased with how they work for me. The inner diameter of the hole is 18mm which is perfect fit for MI airdots.…
Cable organizer made like a small drawer box. Recommend printing with support for some small details like the rails on the bottom part. Print the lid upside down.
This holder was designed for the Samsung Galaxy Buds FE truly wireless earphones, but it can be used for any earphones as long as it fits on the 54mmx54mm insert. It consists of two parts, a hook and the insert where the earbuds rest. The…
Gridfinity Inlay for Xiaomi Earbuds 60x24mm
Designed for Taotronics Soundliberty 92 earbuds. Figured I need a stand to place the charging case, so why not make a charging dock thing for it (charging capability not included). Print Settings Printer Brand: Creality Printer: Ender 3…
Because of its angular arm and textured body, which will help you hold the tool in the correct way, this instrument will help you clean the deepest area of your port. Additionally the other side of the instrument can be used to clean the…
I wanted to combine my earbuds charger and Pixel Stand 2 to optimize the space on my desk. This was what I made and it works great. Here's the earbuds charger that I'm using: https://amzn.to/460mGXA Google Pixel Stand 2:…
Habe es mit PETG gedruckt bei 40% Füllung. Ohrpolster sind vom normalen Winter Ohrschutz genommen, dann noch bei Bedarf etwas Polster unter dem Bügel kleben. Ohrschutz ist nach hinten offen so das keine Stauwärme entsteht beim längeren…
Description A simple tech holder for a phone and JLab Mini earbuds that I created for myself, and I think you would like too. It has holes to run charging cables through. Print Instructions I used Prusa Slicer, and rotated it on it's…
Hey, I just modeled this on Fusion 360, and I am super happy to share my work with the masses, I just made this which is a sturdy 3D case for CMF earbuds 1. One only needs to attach a simple elastic through the hollow hole, in a loop, and…
this is a charging station for the infinitive earbuds case that attaches to the honeycomb wall if you dont know what the honeycomb wall is just search 3d printed honeycomb wall on any browser and you will find out.
Intro A super-simple 3D-printed cleaning tool designed specifically for earbuds and in-ear headphones . It removes accumulated earwax and debris quickly and safely, helping restore sound quality and hygiene — all with a very short print…
Hey, I just modeled this on Fusion 360, and I am super happy to share my work with the masses, I just made this which is a sturdy 3D case for CMF earbuds 1. One only needs to attach a simple elastic through the hollow hole, in a loop, and…
Intro Earbuds Cleaning Tool V2 is a small, easy-to-print earwax remover tool for in-ear headphones and earbuds . It helps you safely remove earwax, dust and debris from your earbuds without damaging the speaker mesh . The first version…
Wired Earbuds Box Keep your wired earbuds safe, organized, and tangle-free with this compact and practical storage box. Designed specifically for everyday use, this case neatly fits standard wired earbuds while protecting them from damage…
Description A simple tech holder for a phone and JLab Mini earbuds that I created for myself, and I think you would like too. It has holes to run charging cables through. Print Instructions I used Prusa Slicer, and rotated it on it's…
This model will give you Onn earbuds a good place to charge. I used 5% lighting infill and no brim and no support.
I wanted to combine my earbuds charger and Pixel Stand 2 to optimize the space on my desk. This was what I made and it works great. Here's the earbuds charger that I'm using: https://amzn.to/460mGXA Google Pixel Stand 2:…
An F-15 Themed charging station. This station supports most cell phones, as well as apple watches and some galaxy watch models. The tower was made to charge galaxy buds, however it also works with AirPods, and possibly other earbud…
This Pokeball will hold your earbuds case and you can hang a key chain ring on it and use it in combination with a carabiner to hang on your pants. I included a photo of the dimensions of the buds case i used. Glue the black part inside…
Perfect earbuds holder for your desk. Holds a wide variety of sizes and even has a spot on the bottom where you can plug it in to charge. (In the picture I have not removed supports, without supports the model will look like the one in…
Wall mounted earbuds dock with cut out and side storage for charge lead. Printed with Jayo PLA Meta 0.2mm layer height, 15% gyroid infill
I recommend printing with PLA due to the required high cooling in the lower parts of the model, add an offset of 0.1mm so that the headphones fit easily into the stations
I have found that it is quite important to giving place for your most used items, when organizing your workspace - this is minimalist organizer for your typical items. I've got one at my work desk and store there earbuds, keys and…
this is a charging station for the infinitive earbuds case that attaches to the honeycomb wall if you dont know what the honeycomb wall is just search 3d printed honeycomb wall on any browser and you will find out.
Use any material , on ay printer . I have used 0.4 nozzel , 0.2 step , with PLA
This was a design I had drafted after seeing Tonitom AirPods Pro Case Molle Clip. This is for the first generation Skullcandy Dime Earbuds case. I did not duplicate the design for the Molle Clip from the original. As stated in the…
A simple and fast print to help clean earbuds and phone charging ports. It features a textured side to help with grip, and the tools on each side are the perfect size for cleaning an earbud or getting dust out of a phone's charging port.…
Small box with sliding lid to store earbuds. No support needed when printing.
For any questions with print settings or assembly, feel free to message me and I will assist to the best of my ability. Happy printing! NO Glue or additional parts required. The model prints as four separate components and is easily…
A replacement for the clip that break. Easy print in a few seconds
You can use 6 each Ø6x4 mm magnets or 3d printet pins if you will assembly it permanent. I would prefer to glue (gluegun) the earbuds and mic in, so it's not rattle around. The STL file has to be mirrored X or Y for second parts.
Earbuds Buddy - Magnetic Earbuds Holder Two version included: exposed magnet and concealed magnet (need to pause the print and insert magnets). 6mm dia x 3mm thk magnets. Use at you own risk! :-)
I recently went to treat myself a little bit and spent a little extra money for a new set of bluetooth earbuds. These WF-1000XM4 earbuds are amazing… and have the price tag to match (for a relatively broke university student, at least…
Tired of your wireless headphones / earbuds falling out of your ears? Well you're in luck cuz you can use this doohicky to secure your earbuds so that they don't keep falling out of your ears. Printed with PLA 0.2mm layer height and…
Protect and organize your wired earphones with this Spider-Man themed earphone case 🕷. The round, compact design keeps your wires neatly stored, prevents tangling, and makes it easy to carry in your pocket, bag, or backpack. The bold…
I don't like things in my pockets, exspecially large earphone pases. The case has holes built into it for the USB Ccharging port and the reset button. Use double sided tape on the front and back of the case to hold it inside the holder.
Pretty simple cup for ear buds to stay in. It should over hang your desk and allow the wires to hang down the opening. Attach it to the desk with some 3m command strips. Print without supports and easy to place and remove earbuds. Print…
I made this earbuds charger because I could not find anything like it for this particular earbuds because it is not widely popular like the airpods or galaxy buds. I used hot glue to put the parts together but superglue would be better…
A simple stand for phone and earbuds. Designed for Redmi Buds 6 Lite.
A slim bedside organizer tray designed to sit on top of a bed headboard or shelf. It has two shallow pockets that are perfect for storing a pair of wireless earbuds, rings, keys or other small everyday items you want to keep within easy…
A super compact and lightweight solution to store your wired earbuds without the bulk. This minimalist case is designed to be as flat as a credit card , making it perfect for slipping into your pocket, wallet, or bag without taking up…
This model will give you Onn earbuds a good place to charge. I used 5% lighting infill and no brim and no support.
A compact and practical phone stand organizer designed to keep your desk clean and your essentials within reach.
A compact desk dock that cradles your wireless earbuds charging case upright with a cable channel at the back, so it always has a home and the charging cable stays tidy. Parametric: adjust the cradle width, depth and cable slot to fit…
Earbuds hooks for Niceboy hive podsie 4 After printing, I finished the tabs by heating them with a lighter.
A desk stand to hold the charging case for the Jabra 65t earphones with usb cable attached. Here is the right angle cable used. It is a tight fit so other cables likely won't work. The part is symmetric so if you get the cable angled the…
This holder is for Anker Liberty Air soundcore earbuds. This is my first design. I hope you find it useful. Thank you. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: 15% Filament:…
This holder is screwed to the underside of a desk or other surface with #6 x 1/2" wood screws. There is a clip for a 9mm diameter headphone extension cable built in with a slot for a zip tie. Maximum width of hanger is 40mm. Print…
Xiaomi Mi Earbuds Basic 2 True Wireless ear hook so they don't fall out of your ear. They can even be placed inside the charging box (but you need to take them off to charge. Printed in ABS. 0.2 layer height. It also let me use a slightly…
The cutout is the actual size of the case so scale down in your slicer so they don't fall through. I printed at 99.5% and I was satisfied with the fit. Holes are sized for #8 wood screws.
I found that the case provided by ISOtunes for their ISOtunes Free wireless earbuds was a tad unstable and I often lost it in my workshop. I created a case that wraps the original ISOtunes earbud case and, via embedded 10mm x 2.5mm…
I did something pretty simple...I took two designs, slapped them together in Tinkercad, and made this. This phone stand also has a holder for earbuds attached to it. I use it to prop up my Pixel 6a and hold my Pixel Buds so I won't lose…
A simple docking station to suit the Jeet Air Plus TWS earbuds. USB-C cutout suits a cable with max length & width of 5mm x 11mm. Use a M5x8 bolt to secure the USB-C cable head in place.
I took my model, made it neat, and added a glasses stand with it. It's not perfect, but I always stress the fact of function over form.
This case replaces the stock Enacfire case so that you can put in a larger battery. It is designed to perfectly fit an 18650. The stock case has a pitiful 500mah battery that lasts about a day of listening. My new battery lasts about one…
It is a small container where you can put earbuds or other little things. The inner diameter is 26 mm, and the height is 90 mm.
These are markers for iPhone lightning cables or wired earbuds. If you are confusing or losing your lighting cable or earbuds with/to others in your houshold or office, this is the solution. Clearly identify your ligthing cables or…
EDIT: Added Fusion360 file or easier remixing, internal diameter and lenght are parametric. Heads up, the parameter for internal diameter should be set 2mm wider than the actual result, I made the inner wall 1mm thicker at one point so…
This is a button cover for the Sony WF-C500 earbuds. The cover fits over the existing button and prevents accidental presses, while still allowing it to be pressed with your finger. I used small strips of 3M double face clear tape to hold…
Uses this 90 degree connector: https://www.amazon.com/gp/product/B078M793HW/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
I flipped the apple watch charger to the opposite side, doubled up the phone holder and added @Charleszard's Bose Quiet Earbuds II charger. 25% infill (support cubic) Supports: snug, 0.2, concentric
TWS earbuds from K-Mart (ANKO) and The Reject Shop are okay for my wife's and my use for podcasts and occasional music listening, but hers, the ANKO TWS, are in a small slippery charger case and my TRS buds' charger has a stupid raised…
Uses this connector: https://www.amazon.com/gp/product/B078M793HW/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
This clip slips over the lid of the earbud charging case to retain an AirTag. Rigid resin recommended.
You can stick the holder with double-sided adhesive tape
Context Maybe my ears have an unusual shape, maybe I'm asking too much: I was unable to run without having to reposition my earbuds every 5 minutes. Since tapping/pressing the earbud is sending a pause command, it was annoying. I decided…
Made a simple holder for my Bose QuietComfort Earbuds in a project to organize some of the things I have around my office. Printed with PLA, 0% infill, 0 solid bottom layers. No raft or brim needed on my FlashForge.
Remixed JBL tune flex holder with Ikea Skadis peg board "connector"
Do you prefer wired earbuds because of their crisp mic recordings but hate the tangles? Search no more! This holder is designed to keep the earbuds and the mic in the central cavity, protecting them from impact while keeping the wire…
Can someone with a Model Y try this out to see if the width is the same as the Model 3?
Sony earbuds holder for Bowflex dumbbells stand. Made for Sony WF-C500 but can be modified to fit other models Here is the case model: https://www.printables.com/model/775376
I made this earbud thing a while back when I was a student I was tired of pulling up a messy and tangled earbud out of my pocket every single time. So I decided to do something about it and wanted to create my simple organizer, Which…
===UPDATE February 7, 2024 Print Profile now available: HERE ===ORIGINAL POST Here's an Wyze Earbuds holder for the Honeycomb Storage Wall (HSW). The inserts only have 3 tabs so the can be removed and relocated easily. Printed upside down…
I tried to find earbud case, but finally designed my own. Print without supports. Please share you makes and consider donation. https://paypal.me/novatormaker https://revolut.me/onovator
A holder for your wallet, earbuds and a credit-card sized card. I desgined this mainly for myself, but maybe it fits your usecase aswell. It most likely does need some supports to print, and costs about 80g of fillament.
A simple holder for earbuds. Category: Computer
wall earbuds holder (Redmi buds 3 pro) + parametric
What this is I needed a small box to keep my cat from chewing up my earbuds. I designed this box to keep earbuds in when I'm not using them. I wanted something easy to open, but would stay closed in a bag. Bill of Materials 2x M3 10mm…
Remix of a Remix - Stick it to a wall or something - I put mine under my desk
I always struggled with not losing my remote, earbuds and finding a proper place for my (battery-driven) alarm clock. I know, this is highly customized for my specific needs, but maybe someone can make use of it, too :) PS: I printed it…
This is a stand/dock for the Logitech G FITS earbuds. The SNUG fit is good if you want to drop the case into the dock without it hitting hard, but also takes some force to remove it The LOOSE fit is good if you want to be able to put in…
![Wireless Earbuds Dock [Taotronics]](https://media.printables.com/media/prints/188566/images/1756694_41891510-24b8-48a7-88cb-846838c7e84a/large_display_b092_pic1_188566.jpg)
