Counting matching models…
Re-mix of the same concept from David - but with Clip-on mounting and it prints easier / lower warpage. Clip-on mounting Shroud Easy on / off without removing screws No supports needed Smooth bottom No airflow restriction only 3.6g /…
Print with 30% infill, 0.1 layer height, 4 walls and 8 top layers. Sand mating surfaces of the middle part with 80 and then 200 grit. The top and bottom parts should print smooth enough to make sanding unnecessary. They should be able to…
Clip on Camera Hood for the Q2 to reduce flare and blooming from LED lights. One is for front (stock) and 200mm LED light bar (see my other models) and another that blocks entire top (for people with risers with light strips). Suggest…
When dialing in my MK4 printer to match the print quality of my Mk3S+'s, I noticed that the MK4 part cooling was inconsistent. Upon further examination, it became clear that the positioning of the MK4 hotend fan was creating…
Final V4 slim design: Clip-on mounting Shroud No airflow restriction Easy on / off without removing screws No supports needed Smooth bottom outer 0.2 skirt for better bed adhesion same angle as MK4 fan holder only 2.8g / light weight For…
The annoying ratchet noise of the Qidi BOX is well known. Personally I had tried to apply grease in the ratchet mechanism to lower the clicking sound. Not really satisfied with the result. It's ok at the beginning. However, the grease…
Some filament rolls have a large, tapered hole through the center. This taper makes the spool crawl across the spool arm while you print, and the oversized hole in in the spool makes the filament roll rock back and forth while you print.…
The stock filament holder is good enough to get you going, but it mounts on top of the printer, introducing all kinds of rocking and vibration as you print. This filament hanger replaces your current direct-mount filament holders and lets…
Use either of these plugs to fill an empty goal when a player is eliminated. The star model has a cutout to hold a rubber band to act as a bumper. Print using any filament with any settings.
Reduction for ELEGOO cardboard spool, print without support, suitable for Prusa Enclosure Mini. Eliminates the inconvenience of spool squealing.
Lego DUPLO brick 1x2x2 optimized for shrinkage (for my printer tested several times) No support needed
Lego DUPLO brick 2x2x2 optimized for shrinkage (for my printer tested several times) No support needed
Eliminate odors without restricting CoreOne ventilation - tested and works perfectly on standard fan settings. A low cost filter to eliminate odours in an enclosed environment. Current cost per filter is under A$6 delivered to Perth…
A simple spacer that eliminates dead zone on the FIRE button of The QuickShot II joystick. If the spacer does not fit tightly on the FIRE button pin, use a small amount of glue to secure it. The photos show the FIRE button pin, the micro…
I never use the disk sander and it is right next to the power switch, so I removed it and made this cover for safety. FreeCAD source files available on request.
remodelled to avoid needing supports, print with a brim :) it is suitable for an m3 bolt or screw
The bracket linked on the website has a corner that protudes into the path of the head when it's at the top of the Z-axis. This version simply eliminates that corner so there's no interference.
Prints nicely flat on the build plate with no supports, but angle it at around 30deg if you want less pronounced layer lines where the phone rests. Can also mirror the file within slicing software (I used Ultimaker Cura) if you want the…
The bracket linked on the website has a corner that protudes into the path of the head when it's at the top of the Z-axis. This version simply eliminates that corner so there's no interference.
A simple spacer that eliminates dead zone on the FIRE button of The QuickShot II joystick. If the spacer does not fit tightly on the FIRE button pin, use a small amount of glue to secure it. The photos show the FIRE button pin, the micro…
Final V4 slim design: Clip-on mounting Shroud No airflow restriction Easy on / off without removing screws No supports needed Smooth bottom outer 0.2 skirt for better bed adhesion same angle as MK4 fan holder only 2.8g / light weight For…
