Counting matching models…
I took the original spool holder for the Voron 0.1 and elongated the length by 10mm. Assembly is the same as with the original one, but 10mm longer PTFE tubes are needed. In the picture both the original and the elongated version are…
Print approx. €1.36–€1.66 excl. taxPreliminary estimate for one variant
Can be printed assembled. If not need to use a little force to assemble it.
Print approx. €2.77–€3.39 excl. taxPreliminary estimate for one variant
This is nothing more than a remix of @ dereksrose 's fine Camera Mount remix - except with an added support leg! The added support leg not only puts less stress on the extended arm but also reduces the wobble as the printer is printing.…
Print approx. €2.12–€2.60 excl. taxPreliminary estimate for PETGSource material: PET
The model was elongated to the same length as the remix by Ernesi to use his remixed side supports. It uses a separately modeled solid bottom which should be printed with grid infill and zero bottom and top layers. This replaces the hex…
Print approx. €4.53–€5.53 excl. taxPreliminary estimate for one variant
This is the upper lampshade part for an existing lamp which had quite some glaring before. It is done with voronoi shapes. There is also an adaptor to center the shade in a seperate file (strong overhangs otherwise). The wall thickness is…
Print approx. €0.14–€0.17 excl. taxPreliminary estimate for one variant
Elongated pentagonal bipyramid.
Print approx. €0.72–€0.88 excl. taxPreliminary estimate for one variant
This model is made as a part to teach students how to get into fusion workflow. Also how to be the part of printables community. Reimagined og figet toy.
I enjoyed this mount but wanted the camera a little further from the print bed. I elongated the arm by 60mm and then also lengthened the mount point so it can accommodate a thumb screw such as this After using this for a while I found…
Display stand for souvenir pressed pennies (elongated coins). Will hold up to 24 coins in total. From left to right the display is designed to hold alternating horizontal / vertical coins (see photo for an example). Printed with 3 walls…
Laserpecker baseplate pin jig L/Straight jig and elongated pins Remix of SANDRO PERUSINI version of L/ Straight jig https://www.facebook.com/groups/lp2users/permalink/1636318066707720 Created channel and longer pins used from the main…
Small and easy to print display stands for those nice souveniers. There is a version for horizontal and vertical coins. No supports needed. International names for those coins so everybody can find this: D/AT/CH: Quetschmünzen,…
This is a simple modification to make the most out of a Creality CR-10 bed. When the model is positioned from corner to corner there is a ~10mm margin to the edge of the build area. Dimensions are 327.7mm Long, 155.48mm Wide, and 240.51mm…
This model is compatible with the lego system.
Elongated Nut DIN6334 - M6/M8/M10/M12/M16
This striking sculpture evokes emotions and is guaranteed to start conversations. Tree Supports on build plate only Partially Powered by image-to-3D from MakerWorld (https://makerworld.com/makerlab/imageTo3d)
This is a remix of "Fast Operation Vise" that is a remix of "Yet ANOTHER Machine Vise". I wanted to have a smaller overall vise, but with longer jaw travel, preferably 100mm. So I designed this model that has increased travel, but should…
This model is compatible with the lego system.
This is just an elongated version of https://www.thingiverse.com/thing:40131 I just doubled the length of the handles. Category: Household Supplies
This elongated buttons and D-pad button have been designed specifically for using by with adapter for Thrustmaster T300RS and steering wheel from of a real car.
I took the original model, elongated it, and then removed the waves and put them back in on different heights so I could print the whole earring in different colors but only have to change between colors by layer. I went Silver - White -…
Parametric Elongated Planter Modern, stylish planter designed in Fusion. The model can be easily printed without any supports and in less time and material. I have added the solid model to print it using Vase mode (spiralize outer…
This is my own can dispenser. If you need different diemensions or anything is wrong you can message me :) Can diameter: ca. 60mm Can lenght: max. 148mm (than you have 1mm on each side buffer) Amount of cans it can hold: 11 cans Max.…
A long block that can be printed using anything
The elongated model is designed to fit a TV-Remote and to fit on my Creality Ender 3 v2 build plate. The longer drawer is 2 hexagons longer (+23.6mm) → Approx size of base: 166mm x 198 mm Other sizes (multiple of hexagons ) can be…
Extension for the Logitech Extreme 3D Pro joystick's throttle.
Minor Remix. Scaled to 105% in length to fit full-size toothpaste tubes and the shaft from the previous model. You may wish to take the original model and scale a bit more, or even use an Xacto knife to cut the slit a bit longer. Full…
Elongated the cylinder portion of the hanger to fit more spool brands.
Updated to view from a different angle.
Designed in Fusion 360 and Tinkercad for 3D printing. Print Settings Printer Brand: Printrbot Printer: Play Rafts: Yes Supports: No Category: Earrings
E3NG 1.2 - Elongated Stepper Cooling Shrouds - to fit 48mm and 60mm Steppers
Use case Glue-on pads for cable ties are not a new invention. But sometimes there is very little width available on the intended surface. Along the cable there typically is enough space (otherwise the cable could not run there). So I came…
original project by @jonnieZG https://www.printables.com/model/104758-car-vent-gravity-phone-holder-v3 I've elongated the seat 5mm for fat phones. Also added cutout to the end of the seat of the sled to hold the phone on ramps or on bumpy…
Ender 2 Pro elongated Led holder remix Support: No Adhesion: No Infill: >50%
Print vertically with normal supports
Key for a commercial dispenser with a "x" shape
We have a series of picture frames that were very hard to wall-mount, because the sawtooth were recessed over 1" / 2.5 cm from the back of the frame. So I made a wall-mountable hook that sticks out 25 mm from the wall, and is easier to…
Lamb M8 for elongated nut for a moonshine distiller. But you can use it wherever the size fits.
This is my own can dispenser. If you need different diemensions or anything is wrong you can message me :) General information: Max. height: ca. 390mm Max. lenght of the dispenser: 412mm Dovetail joint tolerance: 0,19mm Hexagon joint…
This design is based on (Knurled Stackable Pill Case ) By @Diggidydave_179419 Link to the original work: https://www.printables.com/model/639562-knurled-stackable-pill-case Elongated top part of the original design Made it easier to twist…
I added the Slice Engineering Copperhead bimetal heat break to my otherwise stock Ender 3 Pro hot end to be able to print with PETG - CHEP posted a good video about this. I didn't realize that the new heat break, being longer than the…
I really enjoyed the original model, but felt the handle was too small for a good grip. Also I kept bumping into the closest axis+nut. So I've elongated the handle's grip for a better handhold, and elongated the handle's base to distance…
Elongated fluted flower vase
The hooks from the remixed model are amazing and their connection to the base place is perfectly practical and strong, I just needed the tips to be taller to accomodate my millions of leashes so sharing my edit. I only edited 2 - Hook…
Many thanks to the author for the idea of such a bracket. I didn't have enough horizontal movement to move the camera to the side. I added a hinge and extended the rods to 20 cm. I use this bracket for xiaomi c200 camera. Additional parts…
Wishing you good work and fun I would be happy to receive feedback and photos of the make. Thanks
modified the awesome round dry box by rpearsondev to be higher and therefore contain more silica making the replacement less frequent :) Category: 3D Printer Accessories
sewing button - elongated with two holes / 30mm
Our rack is almost 18" wide so I elongated this in TinkerCAD to work. Print Settings Printer Brand: Creality Printer: CR-10 Rafts: No Supports: No Resolution: 0.2 Infill: 50 Filament: any PLA Notes: Print 50% or greater infill for added…
Wingtite drain funnel (elongated).
Elongated bowl with rounded corners 210 x 170 x 45mm On the underside are recesses for self-adhesive rubber feet Rubber feet recomendation: 10mm diameter, 3mm thickness Printing: no supports needed
Not much to say. Its a base for models. Glue your models on or pint them together.
This is my attempt to better my design skills.. Sat down this morning and worked this out in Designspark Mechanical.. I made this tiny V2ish rocket, was looking at a V2 on google and free handed this. enjoy Print Settings Printer: Anet A8…
You can stack up to 5 dice inside this. If its a tight fit just scale it a little up. If a dice get stuck you can press it out through a hole on top / bottom. Inspired by an UNO-Box. :)
Wanted to hang the ‘professional’ size spray bottle of ISO but the head would fit the original model. I separated the frame before stretching so the connector to the hook and the hook itself was left unchanged. Printed on Prusa Mini .8…
This one is only 355mm long instead of 406mm
UPDATE: Version 2 added - Slightly longer machine screw tabs and 15mm thickness instead of 10mm. A quick remix to elongated out the strike plate since my MPCNC uses a thicker belt and two bearing depth. Category: 3D Printer Parts
A longer version of the hinge that I can use with my custom enclosure.
This alternate base allows for a longer SD card reader to be contained inside the SD card holder. The well for the SD card reader is now 50mm deep.
Slightly shorter version (removed lips and added fillets of onewhell mudgard for my coworker's funwheel x7.
Simple elongated plant saucer with angled edges. Scale to your needs.
I printed with PLA-CF using 0.24 layer height, 25% gyroid infill, 5 walls since I wanted it to be fairly strong as the dowels sag when fully loaded with filament rolls. Thanks to Image84 for this great idea.
This model is used with squash ball feet mod and MMU3 upgrade. It connects the buffer to the frame of the printer. Here is the squash ball feet mod that I have used:…
Elongated the pegs for my peg board.
DIY assembly finger joint box made as a design for boardgames. Dimensions: 31.85 x 31.84 x 10.43 cm Works well as a smaller model too. Minimum scale down: Roughly half size of above dimensions. Do not make it too small, the joint fittigs…
This model is compatible with the lego system.
