Counting matching models…
This is Hooky the funny, helpful multifunctional snake hook I designed it for multiple use cases for my Ford Nugget Fiamma F45s awning, where it does a great job. It fits in the 7 mm Keder rail and locks itself under load. It is very…
Hello, This is a wall support for the Fiamma Level-up Ramps. For x2 ramps, you need: x4 supports x2 long screws x2 short screws No need supports, and 50+% infill is recommended. (I personally used 100%) To put it in place, placed them on…
keder tarp clip remixed printed with PETG 15% infill 0.2 layer height print direction on side prevents layer brake (see STL) Use M5 Screen / Nut for this like it's in original.
Ich habe immer das Problem gehabt, das beim Wasserauffüllen mit einer Kanne der Trichter weggerollt ist. daher habe ich einen passenden Trichter für meinen Fiamma Wasseranschluss kreiert. Vielleicht können andere so etwas auch gebrauchen.
I have a Fiamma Aqua 8 water pump, which lost lots of its pumping capacity. Turns out the three acryllic(?) "pistons" inside were cracked and broken to pieces. Replacements are available at Fiamma, but not these pistons as a set, you get…
Keder hook for Awning, e.g., on a motorhome Haken für Kederschiene, z.B. Wohnmobil PETG is recommanded
Original redesign of ‘Fiamma Carry Bike VW T4’ parts made in fusion360. I've put equivalent part numbers in file names. This replaces; Frame spaces with square ones - part #98656-586 Rubber pole sleeves - part #98656-859 Carrier rail ends…
Fiamma Awning Leg Bracket Stl, Step & freecad files
Für die ältere Version des Fahrradträgers (vor dem Jahr 2000) von Fiamma gibt es derzeit keine Ersatzendkappen, also habe ich mir eine eigene gebastelt. (Die neue Version von Fiamma passt nicht auf die alten Schienen) Diese passen…
Replacement for FIAMMA No. 98673S204 + 98673A205 Settings: - PETG - 70% infill, Gyroid
The Cap on the End of the fastening for the Fiamma Bike Rack. Use ASA / PC or any UV and temperature stable filament.
Klemm Befestigung für Teleskop Fuß Fiamma Markise Caravanstore 014 (die Bilder sind vom Prototyp Druck) mit 123d design nachempfunden, da es nur das komplette bein für weit mehr als 100 euro zu kaufen gibt Ich habe den alten vorhandenen…
best printed in petg, or if you like it better by any means in abs no rafts, 100% infill
At some point during the last vacations, I did not crank back in the awning, I cranked off the winch slot to crank it back in. Awning? Winch Slot? What are we talking about? A picture says more than 1000 Words they say! If you are just…
Cover for Fiamma carry bike mounting tube cover
Ich habe es aus TBU gedruckt
This is a replacement knob for Fiamma Skylight Vent. Original was too short for me so I created this one. I'm attaching the Fusion 360 file so you can modify it to get it longer or shorter.
Printed on a Prusa Mk 4 in PETG, and using 100% infil. Supports will be needed. My reading and research suggests that this bracket will also hold the support leg for the Thule wind out awning, but I haven't tested that compatability.
Dá se koupit, ale v sobotu večer ho namalovat a vytisknout z nylonu a v neděli už ho používat bylo rychlejší a troufnu si tvrdit že z nylonu už ho nikdo nikdy nezlomí.
Das ist ein Ersatz Gelenk für eine Fiamma f45 Markise Am besten in petg oder etwas ähnlich hitzeresitztenten drucken. bitte liegend mit support und 100 prozent infill drucken.
This is a recreation of the mounting clip for the Fiamma awning center rafter tensioning arm, models F45s, F45, F65s, F65, F80s, F80, part number 98655A007. Original Tinkercad design:…
🚐 Fiamma Awning AeroSpoiler | Silence & Style Tired of that annoying wind whistle during your highway trips? Or maybe you find your awning's look a bit too "boxy"? This AeroSpoiler is specifically designed for Fiamma awnings (F45/F80…
Replacement of one of the parts of the Fiamma awning leg joint.
zwei Schloss-Schrauben und zwei (Knebel-)Muttern zum Festziehen erforderlich.
For extra strength, it is recommended to print the theeth/top section with 80-90% infill and the rest with 50% infill. Best printed in ABS or PETG for durability
Gleiter Schiene Tisch (FIAMMA) Hier ein überarbeiteter Gleiter für die Wandschiene von Fiamma. Diese Version ist „stärker“ ausgeführt und für den 3D Druck optimiert. Bei einer 28er Tischplatte ist diese Version mit der Tischoberkante…
Bracket to house a Fiamma Water Filler Neck. Normally it would be installed on a camper van for example in the side wall of the chassis itself. We decided to mount it inside of the car, so a small adapter bracket was created. Slightly…
Ordnung für dein Camping-Zubehör – Halterung für Fiamma-Markisen-Heringe Nie mehr lose Heringe im Camper! Mit dieser praktischen Halterung bewahrst du bis zu 4 Standard-Heringe (Ø ca. 6 mm) deiner Fiamma-Markise sicher und ordentlich auf.…
I wanted to connect the fiamma bipot 30 to a normal drain. Later if it is fitted to the final place, i'll post a photo. Print Settings Printer: prusa i3 rework 1.5 Rafts: No Supports: No Resolution: 0.4 Infill: 30 Notes: I printed with…
mit Kupferbandbeklebt gegen Ameisen
Fiamma sells an "optional" rafter/strut that reinforces the center area of their popular awnings for camper vans. I use it all the time. The cross bar supports for our van bed are 15 series 8020. I wanted a way to suspend the Fiamma…
My rafter attachment piece broke that holds the rafter of the Fiamma F45s on my Casista trailer. It was the part that holds the larger piece into the channel. I could have bought one, but I needed to fix it, and since I printed it in PC…
The cross bar supports for our van bed are 15 series 8020. I wanted a way to suspend the Fiamma awning pole that is used to deploy and stow the awning. These hangers fit into the 8020 slot and with a quarter turn are secure and snug to…
The Fiamma waste and fresh water tanks have a sealing in the screwable cap which easily falls out and gets lost. There are replacements available, but all suffer from the same weakness: they do not stay in the cap. This model instead has…
bag awning spare part (fitts to Fiamma) when you stand in front of it, its for the right side.
This is the clip that attaches at the top of the rafter shroud.
For extra strength, it is recommended to print the theeth/top section with 80-90% infill and the rest with 50% infill. Best printed in ABS or PETG for durability
🚐 Fiamma Awning AeroSpoiler | Silence & Style Tired of that annoying wind whistle during your highway trips? Or maybe you find your awning's look a bit too "boxy"? This AeroSpoiler is specifically designed for Fiamma awnings (F45/F80…
Component designed for Fiamma bike racks, used as a mounting part within the rack structure. The bracket is installed in place of the original element and works with the factory clamping system (bolt and knob). Its function is to hold and…
Print with supports, preferably in ABS for this usecase.
This is a fixed tray designed to fit a Fiamma bike rack for PSA vehicles like the Peugeot Traveller and Toyota Proace. I created this tray to hold my jerry can and cooking gear, allowing me to use them even when the tailgate is closed…
A cap to hide the holes in a Fiamma holder for Fiamma Carry-Bike UL on Caravans for example. At the back of the cap there is a small hook, where you can attach a rubber band to snap it in place. Simple and easy solution to hide the hole,…
We have an old bike rack on the back of our 1999's RV. It has four pretty elaborate designed alloy profiles to carry the bikes. Newer bike racks have the V-Shape in different versions, but this one is more like a complex H-Shape. Due to…
Component designed for Fiamma bike racks, used as a mounting part within the rack structure. The bracket is installed in place of the original element and works with the factory clamping system (bolt and knob). Its function is to hold and…
Keder hook for Awning, e.g., on a motorhome Haken für Kederschiene, z.B. Wohnmobil PETG is recommanded
Keder hook for Awning, e.g., on a motorhome Haken für Kederschiene, z.B. Wohnmobil PETG is recommanded
