Counting matching models…
Print in place Toyota FJ40. printed at .16 layer height %15 infill with PrusaSlicer organic supports. Whatever side the print is oriented may have a rough finish near the hood, unless your supports are dialed in. Model was requested by…
2023-11-15 These front inner fenders are designed for the FMS FJ40 Cruiser (1/10th scale). The left fenders encapsulate the servo for the steering wheel and have a slot for a battery strap. These parts were designed and fitted, I didn'…
Toyota LandCruiser FJ40 1977 Wall Art Silhouette model. Adjustable size. I accept model suggestions.
Hi, this is a simple design with a different high layer.. enjoy it.. dont for get your like :)
RC SCALE EXPEDITION OFFROAD TRAILER I recommend following the Build Guide when assembling. The list of necessary hardware is in the Build Guide. Please contact me in case of questions or any confusion. 002_axle can be reinforced by…
Fan: dimension: 30x30x10mm hole distance: 24mm hole diamenter: 3mm You would need: 4x M3x12 screws option 1: electronic switch connected to Receiver https://www.aliexpress.com/item/1005003353247323.html option 2: soldering the +/- wires…
This is a replacement dash control knob, for my radio that I can no longer get for my 71' Toyota FJ40. Printed with my resin printer, sanded, and painted.
Some exhaust parts for "1:10" FMS FJ40. Designed for 6mm aluminum tubing. Requires longer screw for skid plate hangers and glue for the mufflers' halves.
Rear mud flaps for FMS FJ40, their latest big-scale (more 1/7th than the advertised 1/10th) ... TPU of course. Sildes onto the rear body rod. 23-09 : added new mudflaps, 2 short, 2 long, each either plain or with "Land Cruiser" text. All…
Printed plate with a pause for color change. Can be used with any type of filament, printer or printing configuration.
This is a swing away tire carrier for the 1/10 FMS FJ40 Rock Crawler. Requires some extra parts. I used the RC tire carrier from amazon like this one -> https://www.amazon.com/dp/B0BTCZ8T3K?ref=ppx_yo2ov_dt_b_fed_asin_title For the hinges…
Rear mud flaps for FMS FJ40, their latest big-scale (more 1/7th than the advertised 1/10th) ... TPU of course. Sildes onto the rear body rod. 23-09 : added new mudflaps, 2 short, 2 long, each either plain or with "Land Cruiser" text. All…
Basic inner fenders ... nothing fancy, Q&D, just to close the void. To be glued to the body. Engage back first. Might require to fiddle a bit around the leds. Might redo them better in an undefined, but not close, future ... Category: R/C…
A bumper extension to move it forward and provide more space for a winch, but also to look a bit more scale once you move the front axle forward a bit. Uses the same screw sizes as original ... so need 3 more. It's a tight fit ... and…
Easy to print for small printers and big printers. Best if split in two pieces that you can do in the slicer software Half cab setup. ENJOY!
A support for the Westcott FJ400 flash unit to allow added stability if placed sitting upright. I often use my FJ400's to bounce light off the ceiling when shooting around the house. Sometimes I don't want to bother with setting up a…
Needed something to install my PNJ gimball cam in the FJ40 that can stay even if I'm not using it. Fits tight so no glue really required. Just disconnect the lower seats from their feet, install the crate, then reconnect the seats.…
Some exhaust parts for "1:10" FMS FJ40. Designed for 6mm aluminum tubing. Requires longer screw for skid plate hangers and glue for the mufflers' halves. Category: R/C Vehicles
Toyota LandCruiser FJ40 1977 Wall Art Silhouette model. Adjustable size. I accept model suggestions.
Fits late 70s era FJ40. Not sure sure how widely compatible it is with all years. Slot spacing is 85mm, slot width is ~15mm. Print out of TPU. The TPU I used is 95A hardness and worked well with 40% infill. Adjust accordingly if your TPU…
This is a blower wheel to adapt a 92-94 Ranger heater blower motor to an early model Toyota FJ40 land cruiser. I would not print this on FDM as the layer lines would make the part weak in key areas, but it should fit on even the most…
