Counting matching models…
A collection of cover plates for outlets, light switches, and more for all your household needs! Print face side down without a brim. I wanted to create a set of cover plates that leaned into the subtle differences of 3D printing vs…
Outlet shelf remixed for a single gang GFCI outlet. Update: Moved supports to fix overhang issue. Update 2: Added supports to screw holes, changed design of hooks to hopefully make them stronger and a bit better to print. Category: Bathroom
Outlet shelf for a single gang GFCI outlet with a shorter overall length.
Easy print of an outlet face plate with one side GFCI/modern, and the other side Duplex. You can print it face down with no supports.
Over Sized GFCI Cover plate with a hex pattern. Size: 140 H x 100 W Printed with hex shape pointed down. Use 0.25 layers and stop after second layer to swap colors and get a two-tone.
I wanted to model a custom wall plate. I based mine on Alexhart's. This is a simple, chamfered wall plate - The important difference here is I'm including a Fusion 360 export file should you want to make your own custom GFCI outlet wall…
I made this to clear up some counter space on the bathroom counter. The original design intent was to just move the chargers for the 2 PhillipsSonicare toothbrushes to the side of the outlet cover. I kept revising it to accommodate more…
Simple holder to mount the Realsimgear GFC500 under a Honeycomb Bravo Throttle with double-sided tape
This is a custom 3D-printed mount for attaching the rear Wolfbox camera to the back of my GFC. It’s printed in Protopasta HTPLA Carbon Fiber with 4 walls and 10% infill. The camera is attached with 3M automotive double-sided tape. The…
I wanted a simple clean way to run solar cables to the top of my GFC camper. So I created these simple clips that latch into the extruded frame channels to hold the cable in place. The ‘U’ shaped model is to clip into the extruded…
We were enjoying these fun outlet covers, but needed a few for GFCI outlets, so I remixed it and decided to upload it here for others to enjoy. I printed them face down without supports.
These are clips that can be popped into a Go Fast Camper (GFC) rails to hold wires in the channels. I print these on their side so they stand vertical. No need for supports.
This model fit flawlessly. Great job ggppjj.
Redesigned Go Fast Camper Wire clip. These pop in a lot easier and don't slide around in the track unless you make it.
See original model for more info and printing instructions Original: https://www.printables.com/model/735956-storage-b
Make/model of component designed for: https://www.harborfreight.com/electrical-receptacle-tester-with-gfci-diagnosis-63929.html
I made this to be able to interact with microsoft flight simulator without the need to use my mouse. Be warned: the buttons are kinda clunky but it works! Components list: 2x Cut rotary encoder with push 1x Cut rotary encoder 12x…
Designed this Skadis-compatible mount for a Klein RT210 GFCI Outlet Tester, but it should be readily adjustable for other small tools/devices/adapters that plug into a standard North American (NEMA5-15) electrical outlet. FreeCAD…
This is a modification of mrpirkle's outdoor outlet cover. I needed a good outlet cover and their design was great, though it was too big to fit on the side of my outdoor power box and it wasn't ideal for the straight plugs I was using to…
This webbing split bracket is designed for use with the GFC Camper's 0.5-inch T-slots, providing an attachment point for 1-inch webbing. Fabricated from ASA (ABS) the tolerances are tight. For me these brackets require pliers for final…
I wanted a little shelf above my GFCI Single Gang Electrical Outlet Wall Plate. Here it is! I've designed a bit of tolerance in the "glue channels" so it should be relatively easy to print and assemble on most printers (hopefully). *…
I needed to extend a GFCI receptacle box for a weatherproof cover to fit. This extends the box by about 1". Be sure and seal the mounting surfaces appropriately to prevent water intrusion.
This was a quick and dirty creation. I didn't really put much effort into cleaning up the image before I converted it, so it will print messy…..
Created a door handle for the rear hatch on my GFC V2 Pro to make it easier closing the rear panel from the inside. Apply double side tape to the bottom of the handle to securly attach it to the panel without drilling.
I used Normal EufyMake (previously AnkerMake) settings for PLA+ and didn't need to make adjustments. Make sure printer's Z gap is dialed in or the surface could get marred. See original for details:…
PLA Increased number of perimeters to 4 as 2 was not enough given the fillets that I added. I used only 2 perimeters in the first version, as you can see in the photos No Supports Infill 10%
Adding some rooms to my house and thought I would personalize things a bit. Remixed in tinkercad from an SVG and this:
Klein Tools RT250 GFCI Outlet Tester with LCD Display mount for IKEA SKÅDIS. Supports required for the SKÅDIS pegs.
Sharing some useful things I made for my GFC V2 Camper. I used ABS 100% infill. Clip1 I use for the rainfly poles. The only difference in the clips is the pole direction, up or down. I use the clip that snaps upward on the t-track because…
This took a plain base GFCI outlet cover and added a blocking strip to the front. I installed this GFCI outlet in a hallway because of the night light function that it has. Well there are young fingers that must like the nice click that…
Honestly too lazy to type up all of the details but some 1/4 metal rods, some hex screws and the GFC extrusion tab things and you can have yourself some awning connectors for your V1 or V2 GFC :) Print PETG at a minimum and make sure that…
See original model for more info and printing instructions Original: https://www.printables.com/model/735956-storage-b
This took a plain base GFCI outlet cover and added a blocking strip to the front. I installed this GFCI outlet in a hallway because of the night light function that it has. Well there are young fingers that must like the nice click that…
3D printed Flight Control System - GFC 700 Autopilot With backlight and physical indicators that help in VR flight. Works with every plane that has G1000 or G3000 and even with the NXi addon in Microsoft Flight Simulator. It Depends how…
This is a small wall shelf that is held against the wall by a GFCI outlet cover, providing a small utility shelf overhanging the outlet receptacles. This is a remix of another maker's STL file that I sized to fit a SnapPower Guidelight -…
A shift of the original to make the outlet layout horizontal. I left the merged splits in place so it can be adjusted easily to make wider or narrower. One issue carried over from the original is that the screw holes have only a sliver of…
[General] This is the first prototype model of the DK-SF03GFC mount. This will be updated at a later date. So please wait for the update, if you don't have a 3D printer and plan to outsource to external fab to do the 3D printing. Click…
