Counting matching models…
I always wanted to print my own Mouse Feet Skates so as soon as i bought my Bambu P1P I decided to measure my Logitech G Pro X Superlight mouse and make it happen :) This is the first version (and probably the only one) I've created for…
FlashForge AD5x PTFE lined side access covers. Replaces the FlashForge enclosure kit IFS opening trim. This is an additional option to my swingarm guide system. This reduces the gap in the side panel and lined with PTFE tube for friction…
Simple feet or glides for tubular frame chairs such as Thonet as protection against scratches on the floor. The glides are simply clipped on without screws. The indentation on the lower part is intended for the possible installation of…
I made this a while back, and thought I could post it for people to print and what they say about it Depending on your tolerances, you may need to use glue to attach the wings to the fuselage Since you may get blobs, you may want to…
I designed new gliders for our cantilever chairs because the old ones have all fallen off, the gliders fit on all armchair legs with a tube diameter of 25mm there are 3 variants 1. without hole 2. with a 5.1mm hole for an M5 screw 3. with…
Glides for pinball machines so they don't damage your flooring, I printed with TPU filament @ 100% fill
Replacement Glide ø 25mm for deckchair (Lafuma or simular). Fit for all 25mm diameter tubing. Additional to the original size with 3mm thickness, I made a stronger glide with 5mm thickness. Tested print setting: PETG (glide with 3mm…
Here's my solution for furniture, sofas and chairs that slide too much and don't stay in place. Floor protectors that won't slip! Works like the felt glides you can buy nearly everywhere. Now fully printable. Made different “No Glides"…
Ein Ersatz Sessel Gleiter mit Zentrierstift damit er nicht am Sessel verrutschen kann. Am Boden ist eine Vertiefung für die Aufnahme eines Filz Pads... A replacement armchair glider with centering pin so that it cannot slip on the…
These glides are designed to match tubular steel chairs such as Thonet. The glides are easy to install thanks to the screw connection and the corresponding holes in the chair frame. The design fits chairs with 25mm diameter steel tubes.
Hello guys, my problem was, that I don't want to screw a new curtain strip into our ceiling. I created glides to use the Ikea Vidga Curtains on our standard 7mm curtain strip. The clamp was print with 20% filling and without support…
It is a foot glider for a beer bench. It protects the floor.
Harness Hardware for use with 1.75 inch webbing Category: Sport & Outdoors
These are simple feet, or glides, designed specifically for the IKEA IVAR chair. I found the standard IVAR chairs were difficult to slide and would catch on the floor. They'd make this grating noise when sliding on my floor because of the…
This is the plastic part of a nail-on felt pad. The store-bought ones keep failing on me, but the nail and felt part are perfectly fine, so I decided to remodel the part. 24mm outer 22mm inner 1.6mm nail diameter The nail is a snug fit,…
Zapasowe lub ulepszone czarne kulki (rolki ślizgowe) do głowicy odkurzacza basenowego. Elementy te ulegają zużyciu lub zgubieniu, a odpowiadają za płynne sunięcie odkurzacza po dnie basenu bez rysowania folii. Projekt zaprojektowany jako…
Inner diameter is 26.5 mm. However, you can easy adjust by scaling up/down in your slicer to fit every chair. This model is slightly angled for angled feet, if you prefer standard caps:
Glides for pinball machines so they don't damage your flooring, I printed with TPU filament @ 100% fill
