Counting matching models…
This one might be a little niche but... if you're facing the problem of your toddler's water bottles not fitting in the Graco 4Ever DLX Toddler Car Seat cup holder, then you know this pain and I'm here to help! It has been quite…
Replacement for a Graco car seat cup holder. I forget which model of car seat exactly. The keying on the left and right side of the car seat is different so mirror the model in your slicer of choice to get both.
This cup holder fits the Graco All in 1 Car Seat. The car seat has the ability to put a cup on each side but only comes with a single cup. Grandson approved!
The changing table on the model #1780633 Pack N Play tilts because it is only supported on one side. My wife asked me to come up with a solution because she was tired of our baby rolling off. Here's my solution. Print 2 braces - one for…
I lost my original so I designed a custom one that would fit this particular carseat model. Two versions provided of slightly different size. Simple supports are needed for the connector part that hangs. I printed in PLA which was ok,…
This print is for a Graco jogger. I'm not sure of the exact model (we've owned it for years), but it looks to be similar to the current Graco Fasaction joggers. I modeled the connector off the original cupholder, which fits drinks no…
A larger cup holder that fits the Graco Triride 3-in-1 Carseat. Print with support and be careful when removing it. It is easy to snap off the latch on the bottom on accident.
Support for a Graco Pack'n'Play Diaper Changing station so baby doesn't roll off
Use the nut out of the old fan and pres it into this one and it should work fine.
Simple Retainer Clip for Graco Car Seat Booster
We lost the cup inserts for the kid tray of our Graco Jogger on a flight and wanted to gain this functionality again. I designed and printed a two-piece cup insert which fits into the holes in the kid tray. I printed this in ASA, and I…
After our 2nd child was born my wife bought a Grayco Double Stroller (linked below) and, for the most part its a fantastic. However, the stock cupholder left something to be desired. It had room for only one rather small diameter cup and…
These will connect to the top rail on a Graco Lauren Changing Table. Rail measurement 20mm x 30mm. Note: have to unscrew the rail to install. prevents failing off easy The Diaper holder can hold 6 diapers at single time. The small Basket…
Fits into the cupholder so that it can hold taller drinks like water bottles
This is for painters who use the Ultimate Handheld sprayer. Occasionally, we need to invert the sprayer and set it down to clean out the flexible liner, or perhaps to change color. I also invert mine when I clean it, which I do after…
This is a replacement latch piece for the child's tray of a Graco Comfy Cruiser Click Connect.
Makes the existing cupholder fit taller cups
Will need supports but can be printed at lower quality to go faster also check out my cup holder
Small tray to hold Diaper Cream Applicator (Booty Brush). Print with painted on supports on the attachment side.
I had my Graco gun go down on me during a job so I created this model for the Graco sg2 and sg3 spray guns I hope it helps. If there is any adjustments needed please let me know.
I had my Graco gun go down on me during a job so I created this model for the Graco sg2 and sg3 spray guns I hope it helps. If there is any adjustments needed please let me know.
All the items you can find in the market are for 20mm, where GRACO uses 22mm pipe for the handle. This can be printed 6 walls, 99% infill, and will last better than the new one.
I designed this hook because I needed somewhere to store a diaper bag on or near my pack ‘n play. Nothing fancy, but it gets the job done - fits right on the top rails. The hook in the photos was printed with PLA at 15% infill, and the…
This is a bracket to join the frame on a Graco "DuetSoothe Swing and Rocker" model 1967111. Print on end with supports to avoid shearing off the pins. Print Settings Printer Brand: Monoprice Printer: Maker Select Rafts: No Supports: Yes…
Replacement spray angle adjuster (part 4 in diagram) for the Graco 2900 Paint Sprayer. This same sprayer is also sold as the Earlex HV2901 / HV2900. I printed in PETG with supports on the inside. I designed this for a friend of a…
A hanger designed for a Graco high chair tray to mount on the back of an Ikea chair. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2 Infill: 25% Filament: Prusament PETG Orange Notes: 0.6 Nozzle…
Attachments designed to snap on to Graco Pack and Play. I added Diaper holder, wipe holder, and tube holder for cream. if you would like to make your the hooks need a 0.58"x0.59" Rectangular notch and 0.079" thick wall to clip into. I…
Mount any camera with a standard-sized mount hole to your Pack-n-Play so you can watch your baby from anywhere in the world! This has a recessed area where you can insert a screw to connect to the mount hole on the camera. I used a couple…
New parent just trying to make life easier. Noticed that the canopy and fabric on the Graco Snugride Snuglock 35 car seat got in the way of the unlock mechanism, causing difficulties getting seat detached from car seat base... especially…
Holds the little storage section on a Graco Pack n Play crib. I lost the original plastic hooks and printed this and fit tested it for my nephew. Print it on it's side with supports with high infill % for more strength. Set [Print…
Somewhere between kids we lost the attachment tubes that connect the changing table to the Pack ‘n play, so I designed me some! If you’re in the same pickle, hope this helps! And if you need the kickstand part, there's a couple of models…
