Counting matching models…
This is a better printable (no supports needed) version of clé robinet grohe by phil34 . Grohe uses different models of aerator wrenches. See the pictures for how the matching original Grohe wrench should look like.
Wrench to take the aerator out of the front so you can clean it.
Commonly listed as: Grohe 43519 DAL 330 As seen on TV!
Flow reducer for the Grohe water flushing cistern. Replacement for model 42300000
I lost the screw for my sink, and was unable to find a replacement part. Therefore modelled this replacement screw for Hansgrohe Talis s tap sink closer. For more details, see the model number 97522007 in hansgrohe parts list here . For…
New designed service tool for mounting the drain valve of Hansgrohe. This product can used as replacement for #58085000. I design two versions: one with grip for hand mounting one with hex nut (SW19) to use with torque wrench (max 7 Nm)…
The Grohe shower head holder in my mother's shower no longer worked due to the flimsy plastic breaking. I designed and printed a much stronger version. Printed in PETG with 50% infill for strength.
On the picture you see original and rebuild, Just z scale it as you need (larger is easy possible, smaller I would expect max half of the size). More sturdy then original ≤0.4mm Nozzle required to get the teeth with a good fit.
If you want to disassemble Grohe Showerheads, you might want to use this little tool. It should fit the following models: 27130 Rainshower Rustic 160 4-Spray Showerhead 27135 Rainshower Cosmopolitan 160 4-Spray Showerhead 27085 Rainshower…
A replacement part for Grohe faucets that use a thin flexible diaphragm cover over the button to activate the spray. This one fits the Ladylux Café, but may fit other Grohe faucets as well. The Grohe part number is 07379SA1. It used to be…
Hi, i made this as we needed an adapter for my garden hose, especially when using hot / warm water for filling the paddling pool for my kids, and then spraying them. it fits my pull out kitchen tap grohe 30531001…
Compatible Grohe 34mm hex socket spanner/wrench (19332000) for Grohe Grohtherm 2000. Removal instructions
je vous conseil de d'abord imprimer un cadre en coupant le model dans le slicer pour etre sur de la fixation (photo) I advise you to first print a frame by cutting the model in the slicer to be sure of the fixation (check picture)
Spanner to remove the 34mmA/F thermo cartridge from Grohe thermostatic shower valves.
I have a 5 year Hansgrohe shower mixer. The locking shell inside the button cap broke and the button was constantly poping out while cleaning. Here is a replacement. Category: Replacement Parts
To make opening and closing the faucet a lot easier. First remove the black O-ring. Then glide the extension over the faucet end until it clicks in place. Fits Grohe products 20201000 - 20202000 - 20203000.
36mm tool for removing the thermostat from a Grohe rainshower system. The same process as in this video: However the video above uses the 34mm tool instead. The 36mm tool can be difficult to obtain so here is a version that can be printed…
Printed in PETG 100% infill 0.28 lay Print as provided, with Supports for top part, I set overhang at 20%. Works like a charm.
Shower Squeegee holder that clips onto a Hansgrohe hand shower slide bar. Printed in PETG with 0.6mm nozzle, 0.35mm layer height Prusa FAST profile. Squeegee shown is a GUTEWERK.
Hier handelt es sich um eine Ausrichthilfe für die hansgrohe iBox universal. Das Modell habe ich mir selbst erstellt da ich noch Libellen für eine Wasserwaage da hatte… Abmessungen der Libelle Ø 9,5x34mm von der Bucht oder Ali Benötigt…
Our bathtub tap has a knot which switches water flow between direct flow and the shower head. When the water is turned off, the knob switches back to direct flow. I wanted to prevent that behaviour, so I printed this clip-on part that can…
Bouton pour mitigeur Hansgrohe
Grohe 34mm cartridge remover tool from Grohe thermostatic shower valves.
The key for the water drain installation. It can be used as the replacement of the HG 58085000 tool.
Material: ASA Layer: 0,2 Infill: 100%
Fits directly on Grohe Essentials hook, but can fit other hooks with sub 18mm diameter. If you need different dimensions, just scale it in slicer. Recommended print parameters: Minimum filament: PETG Recommended filament: ABS/ASA Layer…
This is a replacement of the original part with fewer holes to reduce water usage further. For me the 3 hole version is working great, but it depends on your water pressure. In the picture green is original and pink is the two hole version.
Bouton Vis pour visser ou desserrer le curseur de douche. Screw button to screw or loosen the shower slider. Print Settings Printer Brand: Creality Printer: CR10S PRO Rafts: No Supports: Yes Resolution: 0.12 Infill: 15% Filament: no name…
Additional simple shower shelf for Hansgrohe Raindance Unica.
Grohe Concetto tap wrench. With pla you will make less scratches when dis/assembling your tap for maintenance and descaling. General measurements Top measured 20mm Bottom measured 22mm How to print Printed in pla+ 50% infill 4 walls Sunlu…
Werkzeug um Perlatoren an Wasserhähnen auszutauschen
Grohe Raindance shower Button Replacement Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Rafts: Doesn't Matter Supports: Yes Resolution: 0.05 mm DETAIL Infill: 25% Category: Bathroom
Once the handle of the shower mixer is full of soap, it’s hard to use, so I modeled a handle ;)
nachdem das original Teil gebrochen ist, habe ich es anhand des original ersatzteils nachgezeichnet.. nicht 100% aber passt.
Additional handshower holder for Hansgrohe Raindance Unica. Category: Bathroom
The Grohe aqua tunes holder broke so I cadded a new one in Fusion 360 and printed in PLA with 0.30 layer using 0.6 nozzle and 15% infill. I used organic supports. Use two M4x30 screws to fix it and re-use the M10 insert bolt from the…
Tilt able showerhead holder for our Grohe Shower, with a somewhat non standard head. The “showerhead holder clamp” fits 20 - 24mm diameter. The screw-on.. thing has a main-bore of 16mm and the lugs with a diameter of 20mm. The clamped…
Pla 3 couche verticale Grille 15%
A single shaver/razor holder for hansgrohe® wallstoris® system. The manufacturer does not provide any shaver holder, so I designed my own. It fits perfect on the horizontal rail system. I printed it in black PETG with 20% infill on an…
Best printed with the bottom side down, using tree support just for the teeth.
The Hansgrohe Casetta Soap Holder C (28678000) doesn’t have very good drainage for water. Therefore, the soap constantly dissolves in it. With this holder, you can keep the soap elevated from the bottom, preventing it from dissolving. I…
Bei meinem Temperaturregler einer Grohe Mischbatterie war das Gewinde im Gussteil kaputt und der Kopf konnte nicht mehr am Schaft des Reglers befestigt werden. Da auch der Sicherheitsknopf für heiße Temperaturen sich schon seit einiger…
Tall, extendable faucets are great for cleaning or filling pots, but the water tends to spray beyond the sink whenever you wash your hands or small things. For this reason, I designed an element that lowers the height of the faucet head,…
A bathroom shelf fitting for the hansgrohe® wallstoris® series. The original ones are only available in two sizes and also do not feature a large water drain at the bottom, which helps keep it clean. I printed this one black PETG on an…
Da durch kalkhaltiges Wasser meine Grohe-Duschkopfaufnahme immer wieder gern mal bricht, ich aber nicht bereit bin ständig eine komplett neue Duschgarnitur zu kaufen und anzubringen, habe ich mir eine Datei erstellt um diesen Teil selbst…
Rafts: No Supports: No Resolution: 0.2 Infill: 40%
Ersatzteil für Duschkopfhalter von Grohe.
A replacement switch for the Grohe RED system. Print with 0.25mm nozzle for perfect fit (needs to be pushed int).
I made a babyproofer for Hansgrohe taps, to get rid of the pointy end on the tap. I printed mine in TPU, but any filament would probably lower the risk of damage.
soap table for Grohe shower set
I Create this soap-holder improvement for Grohe shower system "GROHE Vitalio". The given soap holder with the kit does not allow soap to dry properly, my soaps gets stuck or sticky. So i designed this soap holder who goes above the…
Hook that fits under Hansgrohe AddStoris Q Corner basket . Fits article number 41741140, 41741000, 41741340, 41741670, 41741700, and, 41741990.
I based this model on this design . I redesigned this to tweak the wrench teeth and rim to fit my aerator. Print setting notes: PETG was too brittle/weak and the teeth broke after a couple of uses. PC carbon fiber blend seems to hold up a…
Once again a very specific part that probably won't be much of use for a lot of people… but if you need it you can save on ~250€ by printing your own instead of buying a complete new shower mixer (I'm still not sure what's the correct…
need to find a better way for exporting threads…
Ersatz Abdeckung für Grohe Armatur
The Thing is a replacement thread insert for the Grohe 47453IPO shower shut-off handle because the original replacement part is very expensive. After the print you need to clean the threads from the support material with some tweezers.…
Spare part for mounting the cover of GROHE wall connection elbows in the shower. The clip of the original part breaks easily and the part cannot be purchased separately. Therefore, in such cases, the entire wall connection elbow must be…
Abrazader se el volante regulador grohe esta diseñado a partir del 47984000, hay dos diseños uno solo se puede poner en una posicion y otro en ambas.
Hansgrohe raindance select s has a tray on the shower rod. I made an insert so soap can properly dry. The tray itself has a drain hole. I used the Voronoi Sketch Generator add-in for Fusion to generate the pattern. The insert is 12 cm in…
The adjustment from shower jet to water jet was defective. That's why we designed this replacement part. It consists of several parts, see photos. Repairing is ecologically more sensible and sustainable than throwing it away :-) 2 parts,…
The outer plastic ring of a Hansgrohe Selecta Classic shower head. The original Hansgrohe part number is 28456000.
GROHE RAPIDO SmartBox – Extended Connector A custom-made connector for the GROHE RAPIDO SmartBox , designed to be 1 cm longer than the original part , with a total length of 7 cm . This model was designed specifically for a friend and…
Instructions: download the added gcode and start printing. This key, based on the excelent design by TeeCee allows you to: unscrew the perlator, with the backside unscrew the shower head, to clean the internals of the Hansgrohe shower head
Install it in place with original clips and then rotate 90* and screw original Grohe holder.
This small 3D printed part blocks the lever on a Hansgrohe bathtub faucet, preventing it from automatically switching back to the bathtub spout. It allows you to keep the shower mode active even when the water pressure changes, making it…
This bathtub outlet silencer is designed to noticeably reduce the noise that occurs when filling a bath. By redirecting the water so that it flows onto the wall of the tub instead of falling directly into the already rising pool of water,…
I used PLA with 2 Perimeters. It was bendable enough to install. Added a modifier for dense infill in the angular bits because that's where the old one broke. PETG might be better to withstand really hot water, however most people don't…
If you dont want to drill a hole into the tiles, just use double sided glue tape and stick it to the tile. The Grohe Tempesta Bidet Holder itself is not suitable for gluing. If it works with other Grohe Holders - DILLIGAF. ;-) I wanted to…
Die Handbrause tropfte ständig und zum Schluss konnten keine einzelnen Brausestufen mehr ausgewählt werden. Nach dem Öffnen der Handbrause habe ich gesehen, dass eine kleine Führung abgenutzt war. Als Material habe ich ASA von Prusa…
This is a replacement of the original part that is not individually available for purchase. This part is directly mounted to the aquadimmer 47364000. Part of the set GROHE ATRIO 19399000 When installing, you might need to force a bit or…
shower shelf storage for hansgrohe furniture clips on, no supports needed
A small lever you can pop onto the mixing battery. You maybe need to adjust the scaling for your usecase.
This small 3D printed part blocks the lever on a Hansgrohe bathtub faucet, preventing it from automatically switching back to the bathtub spout. It allows you to keep the shower mode active even when the water pressure changes, making it…
An handle with extebded grip for Ghroe Washer. Printed in PLA with 25% Honeycomb infill and 5 top and bottom layer Print in place without support or brim.
This is a replacement of the original part that is not individually available for purchase. This part is directly mounted to the aquadimmer 47364000. Part of the set GROHE ATRIO 19399000 When installing, you might need to force a bit or…
New designed service tool for mounting the drain valve of Hansgrohe. This product can used as replacement for #58085000. I design two versions: one with grip for hand mounting one with hex nut (SW19) to use with torque wrench (max 7 Nm)…
A hook that fits the lower portion of a Grohe shower setup. clips on snugly
A single shaver/razor holder for hansgrohe® wallstoris® system. The manufacturer does not provide any shaver holder, so I designed my own. It fits perfect on the horizontal rail system. I printed it in black PETG with 20% infill on an…
Opravná díl do grohe grohtherm na regulaci teploty
It is an extension to the bathroom tap that I have made to help my 2 years old daughter to wash her hands. She was not reaching the water. The diameter of the tap is 29 mm.
The GROHE Shower basket is designed for GROHE rod (24,8mm) and is sitting on rod holder. The minimum printer bed size is 180x180mm My printing setup: Material: Prusament PETG Nozzle diameter: 0.4 mm Layer height: 0.25 mm QUALITY Infill…
English / Français / Deutsch : ----- Replacement part for Grohe Grohtherm 800, thermostatic shower mixer Part reference: 405954 (cap for the temperature control valve) I have added a side opening to make disassembly easier. I recommend…
The Thing is a replacement part for the Grohe 47453IPO shower shut-off handle. The original grip plate broke so i needed a new one. After many tries i recommend to raise the part in the slicer about 3mm from the buildplate so that there…
The Grohe Euphoria Cube Stick shower head was damaged and I decided to replace it. It is a copy of the original Grohe Euphoria Cube Stick. Standard G ½" thread for the hose connector I print in PLA Light Gray (10104) from Bambu but I…
Per sostituire il supporto girevole della doccia. fare attenzione va stampata con l'attacco doccia verso il basso altrimenti tende a non entrare. l'ho realizzato con tolleranze strette si può allargare un po'. altra cosa verificate la…
Tired of having to buy this badly designed wrench over and over, I just made it printable. It's still badly designed, and it's gonna break, but I can't fix that :( Suggested material: PETG
Ours broke, so I made a new one. Outer diameter is around 3.2 cm. I don't know the actual model of the faucet.
An handle with extebded grip for Ghroe Washer. Printed in PLA with 25% Honeycomb infill and 5 top and bottom layer Print in place without support or brim.
This is a replacement handle for the Grohe Europlus pop up rod (Part Nr. 46446IP0 or 46418000). Valid for at least these Grohe Europlus single lever basin mixers; 33156000, 33155000, 33153000. In the original handle the rod is threaded…
This clip sits inside the bar and holds it in place. Mine broke, which causes it to come lose. The clip itself sits behind the cover. Remove the cover(s) and you will see it fixed with a screw. But when it's broken, the bar will slide up…
a friend turned to me, with a broken part from the shower system "Grohe euphoria smart control 310 duo cube 3" decided to post it, you never know someone will need. Category: Other
My kids can't open/close the tap without it. Since it's one of the first 3d models I made (about a year ago), you might need to adjust X/Y compensation in your slicer to make it fit snugly. My printer wasn't fully dialed in back then. I…
This insert is used to attach a cold or hot Grohe faucet handle onto a Grohe ceramic disk cartridge (such as 4588200 or 4588300). It may fit several faucet handle models, mine is Grohe Talia. If you are missing the central brass screw as…
a true-to-original soap dish for a shower rail with a diameter of 22mm. Support is necessary.
The middle part of my Grohe Shower Head Holder broke, so I made a new one! Printed with Elegoo white PLA, because that's what I had when I made this. - 0.2mm layer height - 15% infill - 3 outer walls - Brim (noit sure if needed though) -…
I Broke the original glass Grohe soap holder, so I decided to replace it with a print. Print instructions I printed this in Form Futura HDglass Clear, in .1mm layers and 30% infill. No supports.
