917 models
Custom flash diffuser for pop-up flash of Nikon D7200. Since version 2.2 it will fit other cameras as well due to the sliding slot: you only need one M3 nut and one M3x8mm screw. I used this fantastic design for the flash mount, many…
Print approx. €0.87–€1.07 excl. taxPreliminary estimate for PETGSource material: PET
The goal of this project was to prove out the feasibility of a 3D printed lens hood. I purchased a Nikon 50mm f1.4 from KEH that did not include the HB-47 lens hood so it was a good first candidate to prove this out with. The measurements…
Print approx. €2.19–€2.68 excl. taxPreliminary estimate for one variant
9 velikonočních vykrajovátek vajíček k barvení + váleček 5mm pro DO&DRY hmotu, kterou stačí nechat uschnout a pak děti nabarvit barvičkama dle jejich fantazie. (použili jsme tempery i vodovky, akrylové nebyly nutné) vajíčko má 9cm na…
Print approx. €3.01–€3.68 excl. taxPreliminary estimate for PETGSource material: PET
Water filter Sawyer to Nalgene Bottle and Helikon Bottle - Universal Filter Adapter. Inspered by hweat model. Modelet a
Print approx. €2.43–€2.97 excl. taxPreliminary estimate for one variant
This is a remix of Nikon to Telescope Adapter 1.25" by Carsten , but with a 20mm longer barrel for telescopes that need a bit more length to get in focus.
Print approx. €2.23–€2.73 excl. taxPreliminary estimate for one variant
Nikon HK-33-1 and HK-33-2 compatible Lens Hood. Designed for a Client. Before printing, it is important to note that the hole for the Threaded insert will probably need to be adjusted. I designed it for two inserts that I already had. I…
Print approx. €0.04–€0.05 excl. taxPreliminary estimate for one variant
[EN] Replacement of the inner part of the case buckle for Nikon Nivo 5.M/Focus6/Focus8/Trimble M3 total station. Tested on Nikon Nivo 5.M case only - see photos. The entire buckle including this inner part can be ordered at…
Print approx. €0.32–€0.39 excl. taxPreliminary estimate for PETGSource material: PET
A cover for protecting a spare Nikon EN-EL15 (or compatible) battery based on a great cover by @PiJey_88387 enhanced to also cover a USB-C charging connector found on a Jupio EN-EL15C ULTRA C battery. Printed in PETG with 0.2mm layer…
Print approx. €0.55–€0.67 excl. taxPreliminary estimate for PETGSource material: PET
NIKON cup 18-55
Print approx. €0.71–€0.86 excl. taxPreliminary estimate for one variant
A replacement diffuser for the Nikon SB24 Speedlight. A push fit that doesn't fall off easily. For best results print in a white PETG with a low layer height (max 01.5mm). Print instructions PETG 0.15mm layer height 4 perimeters Infill…
Print approx. €2.45–€2.99 excl. taxPreliminary estimate for PETGSource material: PET
Simple wheel extender for Dumborc controllers. It's mean for Absima,Yikong,Amewi and others using this contoller :)
Print approx. €0.15–€0.19 excl. taxPreliminary estimate for PETGSource material: PET
Jedná se o dekoratyvní zápych do květináče.
Print approx. €0.67–€0.82 excl. taxPreliminary estimate for one variant
Silikonformhalter für Kugelschreiber aus Epoxid. Die Form ist für bis zu 4 Silikonformen. Größe: 151mm x 71mm, Einzelnes Fach: 14mm x 12mm x 150mm
Print approx. €3.84–€4.69 excl. taxPreliminary estimate for one variant
Easter egg - velikonoční vejce, Daisy - kopretina, cookiecutters for easter
Print approx. €0.60–€0.73 excl. taxPreliminary estimate for one variant
vytištěno na P1S
Print approx. €4.38–€5.35 excl. taxPreliminary estimate for one variant
Polotovar pro výrobu velikonočního zajíčka z ruličky od toaleťáku. Využití ve školní družině, pracovkách, doma. Na vytištěné nohy s prstencem stačí ruličku jen nasadit. Při jiném rozměru ruličky doporučuji model upravit.
Print approx. €0.34–€0.42 excl. taxPreliminary estimate for one variant
Jedná se o dekorační výzdobu na téma velikonoce a osvětlením elektrickou svíčkou. / It is a decorative decoration on the theme of Easter and lighting with an electric candle.
Print approx. €0.89–€1.09 excl. taxPreliminary estimate for one variant
Žáci si vytvoří 3D model vajíčka, poté ho zpracují v Prusasliceru, po vytištění vznikne matrice pro vyšívání - mřížka ve tvaru vejce - tu pak vyšívaly mladší děti
Print approx. €0.23–€0.28 excl. taxPreliminary estimate for one variant
Předmětem projektu je vymyslet individuálně velikonoční dekoraci dětmi, nakreslit svoji představu na papír, zkusit si z modelíny dekoraci vymodelovat a následně s dopomocí vytisknout na 3D tiskárně.
Print approx. €1.08–€1.31 excl. taxPreliminary estimate for one variant
What else there is to say? It's a lens cap for the Nikon F mount. You always need one more. Print Settings Rafts: No Supports: No Resolution: .20 Infill: 100% Filament: Filament PM PETG Black Notes: Prints without supports. Extra…
Ich hasse es wenn die kurz benutze Silikon Kartusche beim nächsten Mal ausgetrocknet ist... Somit hier ein Verschluss. Damit es optimal dichtet einfach ein Gummiband vorab auf das Gewinde geben (muss aber nicht sein). Der Verschluss ist…
This adapter allows you to mount any finite RMS microscope objective (i.e. objectives that are marked with "160mm" rather than "infinity") on your Sony A, Sony E / FE, Canon EF / EF-S, Canon RF, Canon M, Nikon F, Nikon Z, Fujifilm X,…
UPDATE 20230818: v2 has improved fitment! Designed for Nikon FE2 but might fit other F style bodies! I was tired of all the printable dust caps being less than ideal for printing. I designed this cap from scratch by measuring the body and…
When the 4x microscope objective available from “Reakway” is mounted 150mm away from a camera's sensor, it works wonderfully for photography, covering a full-frame image sensor with a nice sharp image. You can find my standard…
The collection includes: egg rabbit bunny rainbow flower bee ladybug cross church sheep tulip oven glove chick carrot sun [in Czech] V kolekci je vykrajovátko s tématikou Velikonoce: vajíčko králík zajíc beruška kuřátko sluníčko tulipán…
Einfacher Verschluss für Silikonkartuschen. Verwendetes Gewinde: M15x1,5. Dieses sollte auf die meisten Kartuschen passen. Fusion360 Datei ist mit angehängt, so könnt ihr alle nötigen Anpassungen vornehmen.
Remixed bodycap for nikon dslr and slr bodys. Thanks for Physics Dude for original model.
Printed in PETG at .20mm slicing on a prusa mk3s+. The battery is shaped for the larger EN EL-3e battery. But will still fit the more common and smaller EN-EL15. It should fit a 70mm diameter by 3mm thickness O-ring if you would like to…
Nikon Nikkor Z Rear Lens Cap, original looking but slightly shallower (just because it was not necessary since my design has flat top). Tight fit so it sits secured. Original measurements so it protects whole width of flange. If you like…
NO GLUE. "Řehtačka," also known as "hrkačka" or "brkač," is a traditional wooden device that produces noise, similar to clappers, mills, and various other homemade tools that were traditionally used to call people to church services…
I found an old Carenar lens with a M42x1.0mm threaded mount (not to be confused with T-mount which is a M42x0.75mm thread) that I wanted to use with my Nikon DSLR, but the only adapter I found claimed “INFINITY Focus NOT ALLOWED.” This is…
Cover for the mount side of Nikon lenses. Tested with: AF-S NIKKOR 16-80mm 1:2.8-4E ED NIKKOR-S Auto 1:1.4 f=50mm NIKKOR-Q Auto 1:3.5 f=135mm Rokinon 1:1.4/85mm AS IF UMC Designed in FreeCAD Print instructions Print with the open side up.…
This camera grip is designed for Nikon SLR film cameras. Confirmed to fit: Nikon FE Nikon FE2 Nikon FM Nikon FM2N (More to be tested) Through many MANY iterations and changes, here are the final features of The Printed Grip: Improved…
Adapter to attach a Nikon camera to a focuser for prime focus photography. Print instructions Unlike the example in the photo, you might want to print this in a matte black material to avoid reflections. Print Settings No rafts, no…
Look at those two sample pictures! Wow! You can now give any Nikon F-mount lenses or adapters a super macro super power! UPDATE: Added a new retention ring for lens-side mounting. No tools or rubber bands needed! Just snap it onto any…
A box for your Nikon Z needs. Neatly stores 4 Nikon EN-EL 15C batteries, 4 XQD/ CF-Express B and 4 SD cards. If you want it to seal, use a piece of 1,75mm TPU filament, cut it to length and join the ends with ca glue, for example, to…
1 & 2 Nikon EN-EL15 Battery Protection Case
A pinhole "body cap" for Nikon Z-mount. The printed parts are just the holder for the actual pinhole, you'll have to make one or buy one on Ebay (I got mine from fireseller66, a .15mm). Printed in black PLA, it's completely light tight…
Battery Cover For Nikon EN-EL15 Motivation For some reason I tend to lose the battery covers of my EN-EL15 Batteries. Therefore I designed a replacement. It was also a Test for printing with (semi-) flexible material on my i3 MK3. In the…
Das paket beinhaltet: 12 * Ersatz silikon düse
Popis: Jedná se o 3D modely zaječí rodinky. Dekorativní zajíc s květinovými motivy. Určený jako zápich do květináče, do trávy nebo variantně s podstavcem. Tisk: tryska 0,4 mm, teplota: cca 210°C podložka: cca 60°C Testováno s PLA a…
The newest version of my Lens Cap Holders. Now with more supported filter diameters. The following diameters are supported: Canon: 49mm/58mm/62mm/67mm/72mm/77mm/82mm Nikon: 52mm/55mm/58mm/62mm/67mm/72mm/77mm/82mm Nikon (extended):…
Print in PETG for complient flex of the F-mount print in BLACK to absorb any stray light. Have fun big hugs bye
I am a hobbyist camera repairman. I have worked on more than 50 Nikon F3 bodies and 80% of them are missing the motor drive cover. However, the motor drive opening needs to be light-proof and I decided to get this cover 3D modelled. They…
Nikon F mount bayonet. This is the camera bayonet, so you can attach lenses to it. This is not the common cap bayonet, it is oriented like the one in the camera, so you can attach lenses and adapters only in the right position. You can…
Hey there! I made this parametric lens cover in fusion 360 for my girlfriend's camera (Nikon D3100). I could copy this lid due to the lucky fact that my brother has the same camera! However, taking into consideration that this original…
Hello, i always have trouble to create nice silicone joints and startet to look for some handy tools. I saw some good tools in wood, but they were very expensive (4€ each size). Good we have 3D printers, so i designed some and tested…
I took the model from @PhysicsDude and made a few sizing modifications to have it be snug on my camera
Easter bunny cookie cutter size 7 cm Vykrajovátka na velikonoční zajíček velikost 7 cm
Recreation of the Nikon F-mount. Can be used to design accessories such as adapters or macro rings.
These back door latches at the Nikon F100 tend to break off. Unfortunately, the latches are made directly from one piece of plastic with the housing of the door. The new latches are glued. I printed with ABS and used a two-component epoxy…
This is the starting point for another design - but figured it might be useful in case you lost the one that came with your camera. It might fit other cameras as well, but I only have the one at the moment. If others could print and…
This product is a 3D printable replacement latch for the Nikon F80 camera's back door. It offers a durable and precise s
The exposure memory lock button for the Nikon F3 SLR film camera. These things are known to break and fall off the body.
A simple but traditional Easter decoration. No special print settings are required. After printing both parts, just insert the chick into the prepared hole in the base. Happy Easter and don't forget to like. 🐣
I recently bought myself a Nikon Z camera with the idea to adapt a lot of old and strange lenses. Since I didn't want to buy an adapter for each and every one of those (there isn't even one for some of them) I wanted to go with a printed…
Exactly the same as the LF-1 Rear Lens Cap
infill 100% recommended.
ENG: silicone/glue dispenser - caluk gun 4 small screws needed to attach base to the glue tube print with 0.2 resolution no support needed infill min 40% (the more the better) PL: pistolet/wyciskacz do silikonu (dodatkowo potrzebne 3-4…
I wanted to mount my DSLR to an old Olympus VMT microscope. Found a fitting camera attachment (on ThingiVerse) and made a remix with a fitting cylinder for the microscope. Also made one for a cheap Bresser Microscope (but it doesn't…
Easter egg cutters size 45 mm Vykrajovátka na velikonoční vajíčka velikost 45 mm
Add this grip to your Nikon F3 to improve grip without loosing any of the functionality as all the buttons can still be reached. Camera: This model has been specifically designed to fit the Nikon F3 and has not been tested on other Nikon…
a battery holder for nikon en-el15 batteries
I bought a Nikon F3 SLR camera that was missing the flash PC sync terminal cap. I modeled this one as a replacement. It is compatible with other Nikon cameras such as the F F2 F3 F4 F5 FA FG FE2 FM2 F100. I recommend printing with the…
The original design wasn't adjustable, you couldn't fine-tune it by sanding or adding a shim. Sanding the mount side would cause the lens to get loose. Improvement List: 1- I split the adapter into two parts that screw together. This…
Smaller, stronger and lighter than the original. It perfectly fits in both side with the double snap bayonet, so you can reverse it like the original when carrying in the bag. Print settings 0,2mm layer heigth no supports orientation as…
A quick-release clip for the strap that came with the Canon EOS M50. Just push/pull the clip against the metal fixture facing the gap. I recommend printing in PETG or similar at 100% infill, 3 perimeters. The print orientation makes them…
This protective cap is designed for 1K 290 ml Euro cartridges , helping to keep the cartridge sealed, clean, and ready for reuse . It protects the opening from dust, dirt, and drying residue when the cartridge is not in use. Simple,…
The DK-25 Eyecup improves viewing comfort and prevents stray light from entering the viewfinder and diminishing contrast. PLA or TPU 0.15mm layer height orientation shown in the last photo supports are required
I removed the magnet as I thought it was unnecessary for this. The intention was for it to act as a slot, rather than a container you take out and put back in.
Nikon Z mount that works quite well with my Nikon Z6ii. Use it to mount a custom lens on your Nikon Z body. Tag me in your remix ! Have fun with it!
I changed it a bit for better fit printed with my Original Prusa i3 mk2. Cleaned the STL a bit so further customisation (Blendfile!) should be easy. I made it a bit longer so that I could ease the printable but insane steep overhang. So…
This adapter allows a strobe to be mounted to a Nikon F3 camera. This is a cold-shoe adapter, so a flash sync cable is still needed between the strobe and the camera body.
Nikon hot shoe mount cover with Z series logo, it's a remix of another creation from a different user, i made the logo a bit higher so it's more visible and more easy to print that part in different color if you prefer it that way. if…
...I didn't find any and my daughter was insisting...so I created a simple one. PLA works just fine
Please give it a like 🙏 Grip for Nikon Zf full frame. -Use fuzzy skin to add texture. -Use a brim on the print plate. -Print in TPU if you want it grippy. -Use 3M double sided tape to attach. Pro version available here:…
Protect your precious Nikon batteries with this simple and “snappy” case! Printing Use the standard print settings in your favourite slicer. Make shure that “Minimum travel after retraction” (Prusa-Slicer) is set to 1 or lower I used eSun…
Easter Bunny - Velikonoční zajíc layer 0.15 mm material PETG
This is a few improvements I made for mmsaxer1998's excellent adapters for the Nikon Super Coolscans. The first is a support for the rear spool that screws into the back of the scanner. Created this because I keep having issues with it…
This cap is printed in two parts, a F-Mount bottom and a cap. The two parts may be super-glued together before use. I've used PLA, two bottom layers, two upper layers, 0.2 mm layer and 30% infill.
Please give it a like. Threaded low profile hood for Nikor 40mm f2 and 28mm f2.8 Check out my Nikon ZF grip: https://www.printables.com/model/1424562-nikon-zf-camera-grip
Update 19.10.2024: EN Notice: Since I remixed my Front Nozzle holder before the release of Krys own A1 version, it is compatible with Krys ‘A1 mini’ purge catch tray. So please combine my A1 remix with Krys PrusaXlFrontNozzlePurgeA1Mini…
This is a useful battery holder 3mf file that utilizes a dummy battery stl from wdwhite and a gridfinity 2x1 template by Zach Freedman I used it to clear up a stack I had. These are not stackable at the moment It's noted in the part…
slouží pro rovnoměrné rozprostření tmelu nebo silikonu v rozích serves for even spreading of the sealant or silicone in
This insert was made specifically for the 120 x 70 x 40 mm version of the rugged box, that is provided with the model. It can house 2 Nikon EN-EL15c batteries (or other battery not exceeding max dimensions of 56mm x 40mm x 21mm), bellow…
Two types of lens hoods to fit Nikon AF-S 70-300mm or any other Nikon 58mm lenses Category: Camera
I wanted to design this braided whip last year, but I was missing modeling skills I needed. This year it worked :) The most difficult part was to understand the pattern, because on thing is the process of making it from willow twigs and…
Adding Custom Text: Import the cap object in your slicer, or open the .3mf file. Right click the cap object, and select “Add Negative Volume” > “Text”. I find it easiest to position the text from the top view (View menu on top bar > Top,…
I am pretty sure that the last time the battery cover for my Nikon N2020 film SLR was seen was ~10 years ago. It has the optional MB-3 4xAA battery holder, which was kind of annoying to have to duct tape over to get the batteries to stay…
Lens cap for the Nikon Z mount Check out my Nikon ZF grip: https://www.printables.com/model/1424562-nikon-zf-camera-grip
Die perfekte Silikonfuge im Handumdrehen. Mit meinem Silikonfugenabzieher sind normgerechte 45° Fugen von 6, 8 und 10mm möglich. Ich empfehle die Variante aus TPU zu drucken.
Update Nov. 3rd 2024: Based on Genes comments, I have made a 1mm and a 2mm raised version. There is also a new improved debris bucket remix (Prusa XL Bucket for 11.6mm wide nozzle brush.stl with 12mm cutout). The excellent nozzle brush…
Easter egg decoration, Velikonoční výzdoba
Printed in Prusament PLA Galaxy Black - 0.10mm Detail - Support on the bed only - 15% infill - 5h42 printing.
Dieses 3D-Modell stellt Silikonsticks zum präzisen Abziehen von frischem Sanitärsilikon dar. Die speziell geformten Sticks erleichtern das glatte und gleichmäßige Abziehen von überschüssigem Silikon, insbesondere in Badezimmern oder…
![34 Easter cookie cutters / cutter [Velikonoční vykrajovátka]](https://media.printables.com/media/prints/435476/images/5805640_44fba56e-4ed8-4c99-bc52-03e594d9d916_3a0c1e26-eaa0-48f4-803e-af550d92d5b4/vel2.jpg)
