Counting matching models…
Introduction A while back I designed this other handle for the Einstar 3D Scanner: https://www.printables.com/model/364038-einstar-handle I used the feedback and experiences from that one and designed a new updated model. Of course, it…
I've designed this handle to snap onto the scanner body, and secure it in place with a thumb screw. No supports needed, but I did use a brim to help the base stick. I printed it in PLA, but I'd almost recommend PETG. The thumbscrew is…
This grip works great, but if you are new here, I recommend that you instead print my MK2 grip instead: https://www.printables.com/model/388834-einstar-handle-mk2 This is my attempt at making an ergonomic grip for the Einstar, it is…
Shining3D Einstar 3d scanner handle with protective case and dock station push button and handle assembly requires 7pcs 2,5x16 screws dock station requires self adhesive pads to achieve grip on table (15x15mm) and custom cut microporous…
I want to release to the public of my first design of a handle for Shining 3D Einscan 3D scanner. EINSTAR is an affordable handheld 3D scanner, makes high-quality 3D data available to everyone and, in my oppinion, is the best consumer…
Zapraszam do filmu z budowy powiększenia Baterii do kosiarki Briggs&Stratton InStart 775IS… - Jeżeli chciałbyś zapoznać się z tym co robię na YouTube i Facebooku Zapraszam: https://www.magazynowanie-energii.com - Lista wszystkich…
Created this quick scan of a Einstar Rockit with my Creality Sermoon S1. Model looks a bit rough on some paches since I didn't want to use too much scan spray on my new scanner. Added a second scan I took with the Einscan Rigil. Needed a…
So if I had my time again I wouldn't bother doing this - I'd just pay the money for the stupid proprietary Briggs and Stratton Instart battery. But once I started I was kinda committed… This project is probably of quite niche appeal, even…
3d scan of the einstar 3d scanner. It is missing the lower black part.
The EINSTAR VEGA comes with a stand for the calibration board, but unfortunately, it cannot be stored in the case. This stand is foldable and can be stored inside the VEGA's case. I have used it with my VEGA and confirmed that calibration…
I am pleased to share my ergonomic solution for the Shining3D EinStar scanner to you all. As always, I started with the project by making 2D sketches first. I then 3D printed the scanner model where I custom made a clay model. After…
Einstar Vega 3D Scanner Handle for Larger Hands After our first tests, we found that the standard handle of the Einstar Vega 3D scanner can be hard to use for folks with bigger hands. To make scanning more comfortable, we've designed a…
I designed this case in Fusion360 and printed on a Bambu X1C with AMS and PLA. I started with a 3d model using t-splines in the form workspace. After the first test print showed minor adjustments to be made. I then converted the surface…
Einstar 2 mount for the Einstar 3D Scanner Stand. Threads for ¼". So no nut required. A nut can be added anyways though if you want to.
1. Inibisce le alghe verdi e promuove la crescita delle piante -Inibisce la crescita e la riproduzione iniziali del fitoplancton. -Attiva i oligoelementi per promuovere la crescita delle piante La promozione della crescita delle piante…
Propeller spinner cap for popular RC aircraft Volantex TrainStar in equal scale with side bolts mounting. No supports needed. For 6mm shaft Equal scale If you like it, please support me: Paypal: [email protected] Skrill:…
I purchased a 2nd hand Einstar 3D scanner and setup a USB network tunnel to scan remotely using my powerful desktop PC that lives downstairs. I therefore needed my phone to provide remote desktop access for live scanning feedback, which…
I printed it with ASA and PETG and it is okey. Need to print two pieces, it is higher than my printer. From inside I made silver tape to reflect light back to the aquarium.
This is a folding stand for the Einstar Vega that is compact and fits into the original storage case. It is a remix of an existing design but with a print in place hinge eliminating the separate pieces. Printed in PETG with 0.20mm layer…
Twinstar M5 Halterung Eine Lösung für schlechte Saugnäpfe. Der Sterilisator kann mit der Halterung einfach an dem Aquarium angehangen werden. Die Halterung ist für die Rückseite vom Sterilisator konstruiert und wurde an einem…
I have a couple of RC model airplanes where the wings are held together by two plastic elements. In the event of a hard landing or worse, these are designed to break while safeguarding the wings. It's not easy for me to find these spare…
Print from TPU, cut out the modeled-in support rectangle, assemble with two M3 countersunk screws and nuts. Rigid filament will not work, grip upper is scaled down lengthwise by 0.5% to create tension when assembled around the scanner.…
Two-piece mount for retrofitting a nose gear on the multiplex Twinstar. For more stability, a brass sleeve must be inserted into the mount. The gear wire is then secured with set collars.
This 3D Printable Case with Handle is designed for a wireless All-In-One 3D scanner “EINSTAR VEGA”. Recommended Print Setting： Body Case & Handles-General TPU 95A: 3 walls, 30-40% infill, 0.1-0.2 Layer Height Body Case & Handles-BambuLab…
EN: These are two 3D laser scans of a Panasonic ES-LV67 shaver using the Creality Sermoon S1 and Shining 3D Einstar Rockit 3D scanners. The scan on the left (green) is from the Sermoon S1 and the one on the right (orange) is from the…
Includes a downsampled rockit mesh from @PrintedForFun
EN: These are two 3D laser scans of a carved East African candle holder, made with the Creality Sermoon S1 and Shining 3D Einstar Rockit 3D scanners. Both were scanned with 0.1 mm resolution and standard settings. Both scans have 1…
This is a replacement door for the Volantex Trainstar Ascent. The door is made to be very thin and light. If printed curved-side-down it should require no supports. You will need to use magnets or a pivoting catch to hold the rear.
Protective holder for a spare Alpinstars Tech-Air 5 Cartridge. Share your Make :)
I had an old Twinstar light lying around and needed some lighting for my Nanocube, so I decided to make it fit. I just cut my 600c and with a little soldering I got a 300c with double the width. For that I needed a new frame to hold the…
Wing mount for popular RC aircraft Volantex TrainStar for two MPX connectors. two wings center clamp two MPX connectors mounting for flaps/ailerons/lights bottom part with adjustable connecting length. Best fit! Installing the wing in one…
Es ist ein wirklich simples in 3 Minuten gezeichnetes WebCamCover. It is a very simple 3 Minutes Project…
A remixed grip for the Einstar Handle MK2 intended to be printed in TPU (others are probably fine) and glued to the handle. To be printed with the " Single Extrusion - Separate Grip" version handle! Go get the other parts from the…
Fairing for wing and fuselage parts for popular EPP EPO aircraft such as Volantex TrainStar, Ranger, Multiplex Funcub and others. Print in one layer in standard mode or vase mode. Very thin and light! No support needed. Cut with scissors…
Rudder mount for popular RC aircraft Volantex TrainStar. If you like it, please support me: Paypal: [email protected] Skrill: [email protected] ★ Thank you! ★
Motor mount Volantex TrainStar. Replace original plywood motor mount inside the body. Glue it with CA glue! If you like it, please support me: Paypal: [email protected] Skrill: [email protected] ★ Thank you! ★
Standard handles (part of silicone case) are just not convenient for me. Also my finger slips and interferes with the cameras all the time when using it. Handles have 0.15 mm clearance built-in. Mounted on a square profile, secured with a…
Gusset for repairing Volantex TrainStar motor wall. If you broke it in this place , just print this gusset and glue it with CA glue! If you like it, please support me: Paypal: [email protected] Skrill: [email protected] ★…
Soporte para luces led Twinstar 600S con varillas de 4mm. Para grosor de cristal de 8mm. Imprimir con PLA, PET-g oABS. No necesita soportes. 2 líneas de perímetro y relleno del 20% es suficiente. Twinstar 600S LED light stand with 4mm…
Rudder in Volantex TrainStar is so overladed: horn and rear chasis. So I made this mod for unload this part Use 16mm RC hinge Glue it with CA glue! If you like it, please support me: Paypal: [email protected] Skrill:…
If you happen to be one of the few who owns an INSTAR IN-8001 Full HD camera , this wall mount might be for you. Two screwholes allow for the holder to be mounted on a wall using 4 mm (shaft) / 7.5 mm (head) diameter countersunk screws…
A solid case for your Einstar Rockit. Uses a 25x3mm flat bar metal (your choice of Al or Fe) to hold the case together. You now have a super strong way of holding your 3D Scanner, and you can get in over or under your car :)
the OpenScan Benchy 3D Scanner comparison, see https://github.com/OpenScanEu/OpenScanBenchy/ We publish all the original files (send by the participants) as well as the aligned version shown in the final rendering. Feel free to reach out…
Made a cover from plexiglass for my aquarium and lightduct for twinstar light, so the light goes not shine through plexiglass. Did cut opening in to plexiglass to incorporate the wider side of duckt. supports are required, printed out of…
EN: These are two 3D laser scans of a Panasonic ES-LV67 shaver using the Creality Sermoon S1 and Shining 3D Einstar Rockit 3D scanners. The scan on the left (green) is from the Sermoon S1 and the one on the right (orange) is from the…
Protective holder for a spare Alpinstars Tech-Air 5 Cartridge. Share your Make :)
Ever want to use a retro camera but put off by the lack of modern technology in these cameras? Now you can have the best of both worlds! Turn your Ace Pro 2 into a mini retro camera with 3D printed housings. Come with 2 interchangeable…
Since most of the objects I scan with my Einstar Scanner are medium-sized, I concluded that creating a Scanner Stand for my manual turntable (lazy susan) would be an ideal solution. This stand will resemble the one used in the EINSCAN-SE…
