Counting matching models…
The perfect display/travel case for your Dummy! If your favorite head doesn't fit, tell me in the comments and I might get around to do some custom ones or check one of the available remixes! Print instructions: Wall Order: Lids: normal…
Now Female Dummy 13 fits should fit even thickest mods with open hands watch out for boobs 😅
Einfacher erstatz für den Originalen Kunstoffdeckel der ständig bricht. Dieser aus TPU wird defenetiv länger halten. ------------------------------------------------------------------- Simple replacement for the original plastic cover…
3D model for a display version of my 4m wing span RC glider. Printed on my MK4 1/60eme
Unable to find the locating pin for changing the timing chain of a BMW K1200 I decided to model it myself. Parts number are: 83300401482 and 11 1 842 I tested it myself without any issues with the following configuration: Material : PLA…
This is a static model of the popular training glider ASK13. The model comes in two ready to use bluid plate. If the outer wing part is too difficult to print straight up, it might be a good idea to print it flat. Printed just fine on my…
Note: The Ethernet Module PINs didnt land where I expected based on the model, so I used a knife to cut the lower two standoffs. I attempted to replicate this in the .STEP but its not tested and certainly would be below the expected…
Just the awesome EZPickleRick model from "ideawizard" with Dummy13 joints.
Bei meinem Nissan Micra war der Verlierschutz für den Tankdeckel gebrochen. Ich habe dieses Ersatzteil mit “TPU Medium” von Extrudr (A98) in weiß und anthrazit gedruckt und mit einer M4x16 Schraube und einer Mutter unter der Tankklappe…
You need to reset size of the circle to 70 mm. I did a filament change after base printed.
it needs support on only a few parts but they are probably printable without the support. specifically what i needed support on were the peg leg, the coattails, and most importantly the hat. (i don't think i used support on the collar but…
Replacement knob for manual Nissan Micras. Confirmed to work on canadian k13 micras. Just press the new knob on and slip the boot around it. If you are in a hot climate, print in PETG or even better ASA or ABS.
A under desk mount for my old Focusrite Scarlett 2i2 and my new FiiO K13 R2R. I realize that pretty much no one will have this exact combo, but since one of my viewers asked for it, I figured I just might upload it. Especially for those…
The Original Model parts not compatible with this model as sizes are slightly different.
Simple tip holder for electrolux vertical vaccum model STK13A.
Missing your K130 drip cup.... well here one you can print 2 parts -drip drawer and top plate
Printed in ASA. This will clip to the oem speedo by sliding.
This guard fits over the blades of the Tefal "5-Second Chopper" (900-ml-Version, Model K13204). It covers the sharp edges of the blades. Material: PLA or PETG (PETG is recommended for durability). Layer height: 0.20 mm Infill: 15% – 20%…
Had a go with Tinkercad trying to make my first thing and this is what i came up with, needed some scaling in Cura but managed to make it work :) if it is not quite right in any way then the files are saved at tinkercad's web site. I plan…
Build a door open counter and alarm sensor with WisBlock Reed relays are often used for contactless switching in many applications. The reed relay is normally open, but when a magnet is getting close to it, the relay contacts will close.…
Simple tip holder for electrolux vertical vaccum model STK13A.
This guard fits over the blades of the Tefal "5-Second Chopper" (900-ml-Version, Model K13204). It covers the sharp edges of the blades. Material: PLA or PETG (PETG is recommended for durability). Layer height: 0.20 mm Infill: 15% – 20%…
This is an add on that you could glue onto the lower case or the lid to go around the edge of the case so that the lid could close on female Dummy 13s. Use in addition to MK13 - A Female Dummy 13 Case
This is a wall mount for the "boxy" Orbi WiFi access points. There are tons of designs for the other models, but not for this one. Since nothing existed, I made it. The bottom and sides are open so that cooling should be unaffected. I…
Lvnatic got cool idea making MK13 - A Dummy 13 Case I wanted version to fit different Dummy 13s versions so after making cases that fit my needs I decided to publish .step file for other people to remix. P.S. yes it was because female…
Be a gentleman and make room for a Lady(13) ! It's a little bit taller to accommodate for the bigger chest. For an optional lid and easy to follow print instructions, check the original page. Enjoy!
I bought this keurig used and it was missing the drip tray. I found this model on thingiverse, but I didnt like the little coffee cup holes, so I just removed them and added three rows of simple holes instead.
