Counting matching models…
keebcu - andimoto7583 mechanical keyboard This is one of my keyboard designs I made with my keebcu keyboard customizer. It is a 75% mechanical keyboard which can be printed on smaller printers such as Prusa Mini. If you want to build the…
When I started using my new Iris I realized that the added height from the official 3D printed case available in https://github.com/keebio/iris-case made it slightly less comfortable than it would've been if I had kept it low profile. I…
Remix of skrat19's Keebio Iris v4 case at https://www.printables.com/model/66218-iris-keyboard-sandwich-case Changes made in this remix: Updated hole patterning to fit Iris PE middle layers Tightened hole sizes to allow threading into the…
Wrist rest for my Iris mechanical keyboard from keeb.io. This is the PCB case, and these fit right up next to it. They raise your wrists a little, but don't provide any tenting. They are also not terribly heavy, but mine stay put. This…
I needed to reprint my beekeeb case after a screw stripped out and didn't see the files anywhere. They were nice enough to email me the STLs so I thought I would share. Not the most rigid of cases and I plan to design one from the ground…
This is one of my keyboard designs I made with my keebcu keyboard customizer. It is a smallTKL mechanical keyboard with ISO layout which can be printed on smaller printers such as Prusa Mini. Small TKL is TKL keyboard but squeezed…
keebcu - andimoto smallTKL - mechanical keyboard This is one of my keyboard designs I made with my keebcu keyboard customizer. It is a smallTKL mechanical keyboard which can be printed on smaller printers such as Prusa Mini. Small TKL is…
This is one of my keyboard designs I made with my keebcu keyboard customizer. It is a 75+% Q1 Layout mechanical keyboard which can be printed on smaller printers such as Prusa Mini. 75Q1iso means 75% size with Keychron Q1 style keyboard…
The FelixKeeb is an open source 5×12+4 (5×6+2 on each side) split ortholinear keyboard with hotswap sockets support released by beekeeb . It is based on Cipulot’s helixhschoc and MakotoKurauchi’s helix . Threaded brass spacers m2 × 7mm,…
Originally created for a GIBKEY G68, keebcover is a keyboard cover designed with smaller printers in mind. I have an Ender 3 V3 SE, so I made sure that this model can be printed in one go, while making good contact between the sliced…
I made my own Analog Keeb. Check out the video here: Check out the Github Here: https://github.com/tommybee456/DIYAnalogKeeb
How to play ? Players throw a wooden or plastic ball down an inclined ramp, trying to get it into holes of different value. We hope you enjoy this fun little game for two players!
This is a simplified 1:1 version of the KeebDeck Keyboard. It can be used for size reference. Not recommended for renders, there are pretty .step files on GitHub . Learn more about the KeebDeck Keyboard from https://keyboard.keebdeck.com
I wanted to make a Kinesis Freestyle 2, but better. Between the Keeb.io Sinc, the FR4 plate kit, and this 3D print, I've accomplished that. The pieces tent the keyboard at 15 degrees. The print just barely fits on my Ender 3 Pro (you've…
Wireless CRKBD skirt for a 3x5 wireless version. V1 was too wide, shrunk the width and height by 2mm so it's snug. Width was 1mm too short and snug. Expanded across to fit
Designed for the Keeb.io Viterbi 2.0 split keyboard. I did not build my keyboard (pictured) with a switch plate and I'm not sure if the plate will fit with this case. This design is intended to mount the PCB directly to the screw posts in…
Remix of ceraphim's Keebio Iris v7 case at https://www.printables.com/model/332654-keebio-iris-v7-case-m2-direct-thread-sandwich, but as a “pie” instead of “sandwich”. Changes made in this remix: Combined the bottom-plate and middle layer…
This adds a standard mouse button switch to the trackpoint shield from Holykeebs. It is still an early prototype, and the right hand corner doesn't click as well as the left hand corner, but it works. I used a thick (1.25mm) paperclip to…
UPDATE: I'm mad. Absolutely mad... I made this: Disclaimer: this project was printed by JLC3DP at my own expense, no affiliation, but I do have to say; amazing service. I do however NOT recommend ;P Because then my keyboard is no longer…
An 8-bit frog made entirely out of cubes in Tinkercad
Keebio Sinc tilt /tent design. All variant of right half are viable with the drop in (removable) arrow key spacer and the encoder drop in mount/cover. The left half is non macro. I used 10mm hex M2.5 standoffs for all mount points along…
Tented at 11 degrees. Base doesn't need too much infill. Wrist rest is printed in TPU along with the feet. I found that spiral infill at 5% with 2 walls and 2 top layers had just the right amount of give for a comfortable cushion. Files…
KBO-5000 is closest keyboard to what I want, and they discontinued it…. This only contains the top layer and PCB support of KBO-5000. You need rest of the model from official github to complete the case build. M2 Threaded Inserts are…
Slide this piece in-between the two middle panels of your EX2 to hold it in place at 90 degrees. Printed with PLA, 0.2 layer height, 4 walls, 10 infill
Hastily made set of spacers that screw to the back of the Tildagon to sit flat on a desk. Requires 3 x M3 x 10 Socket Head Cap Screw for screwing the back of the Tildagon to the midboard, and 5 x M2 x 10 Socket Head Cap Screw…
A handwired TKL keyboard with an integrated PMW3389 trackball, a 5° tilted case, two extra USB ports, QMK and Vial firmware. I wrote up the whole build on my site: https://salavat.me/trackboy/
A handwired ortholinear keyboard: 33 keys, RP2040, QMK and Vial firmware, with a strap like on Wooting keyboards. I wrote up the whole build on my site: https://salavat.me/tinyboy/ The layout is inspired by the ScottoLong by Joe Scotto
Remix of ceraphim's Keebio Iris v7 case at https://www.printables.com/model/332654-keebio-iris-v7-case-m2-direct-thread-sandwich, but as a “pie” instead of “sandwich”. Changes made in this remix: Combined the bottom-plate and middle layer…
UPDATE: I'm mad. Absolutely mad... I made this: Disclaimer: this project was printed by JLC3DP at my own expense, no affiliation, but I do have to say; amazing service. I do however NOT recommend ;P Because then my keyboard is no longer…
I really like the low profile of the Iris LM for mobile use, but for stationary use I like to tent my keyboards. The tilt is 10 degrees but ask me if you like different angles. I tried 15 degrees but found it too steep and bulky. The foot…
The frame gives the KeebDeck nice, rounded edges and adds a little more protection from dust and other things getting between the PCBs. I printed it on my Mini with the USB opening pointing down, supports enabled, and no brim. To install…
Modified from official Sinc case model, this version allows me to stack a numpad with arrow column on the right side of main keyboard. No PCB is broken. (The problem I want to solve: there is no keyboard on the planet meets my…
A simple, retro-inspired case to keep your KeebDeck Basic protected if you want to just throw it in your bag or backpack. Just like a real cassette tape case, it contains a simple locking mechanism to stop it from opening on its own. Make…
The Description for KeebDeck Basic you can find under: https://www.solder.party/keeb/ UPDATE: Added STEP File. Have Fun!
The case here is the for the left hand side of the keyboard. Simply mirror it to get the right hand side. Using a Prusa i3 Mk3S, it should all press-fit nicely in place. All the sources can be found at https://github.com/ithinuel/wilskeeb…
Adds on to Keeb.io ‘classic’ Sinc case https://github.com/keebio/sinc-case/tree/master/older-design (I did take maybe 2mm out of the Keeb.io middle layer height for lower profile, optional) 10deg tenting Assembly: M2 heat sets into the…
Adds on to Keeb.io case https://github.com/keebio/kbo-5000-case (I did take maybe 2mm out of the Keeb.io middle layer height for lower profile, optional) 10deg tenting Assembly: M2 heat sets into the left/right “open” tenting parts, and…
Work in progress… In Progress: The left side needs a little wiggle room for the PCB Case to slide into. Wrist rest with adjustable feet to match. Rework top covers to not need the plates from Keebio merging. Version: 2 Notes: Adjustable…
I made this because it didn't exist lol. The bottom plate is a pretty tight fit, so it might take some coaxing or light sanding. Also might post an update eventually to address any other issues. Print both sides by mirroring the model.
Why Did I make This? The semi enclosed version of the case where you only take the middle layer is very susceptible to dust. Because I live in a dusty basement in a humid city so the dust gets stuck on there real bad and I'm sick of…
Pretty straight forward model, I just took the middle layer provided by Keebio and tented it to 15 degrees. This should work for any Phoenix Edition boards. Print upside down. At this point you obviously cant use the provided screw…
