Counting matching models…
This model is a part of the conveyor belt collection , but can be used standalone. Printing instructions: - Print flat Assembly instructions: - Press 2 M3 threaded inserts in the holes on the side - Use 2 small M3 set screws to secure the…
Andor / Mandalorian s3 version of the DC15S carbine as seen in the flashbacks with clone troopers. I did my best to make it as accurate as possible given the limited reference material available at the time of uploading. This blaster…
I have a bunch of light switches that need to stay on (or off) all the time. Turning them on (or off) will cause issues. So I designed this cover, and gave you two options: one has a slit so you can use a small tool to slide the switch up…
I recently purchased a Craftsman 109 lathe off of Craigslist. Unfortunately, not all of the gears were present. After a LOT of hunting, I finally found all of the information I needed to create DXFs for the gears at…
A remix of clubclays AudioEngine A2+ volume knob from ThingyVerse. I found that the original slipped on the volume knob, so I created a version that replaces the stock knob. Slide off your original knob and press this one into place.
Fit tightly to the inside of a lynx muzzle and keyed for 40cm. Alternatives provided if your barrel pushes the notch too far forward (marked as the tenths of a mm it's moved).
Bear with me here. I have a 8500 BTU rated portable air conditioner from Hisense (Lowe's: https://www.lowes.com/pd/Hisense-500-sq-ft-115-Volt-Grey-Portable-Air-Conditioner/1000537611). As is often the case with disposable electronics, the…
Update April 23 2025 On the Nylon Set Screws The threads don't necessarily hold strongly within the hole. I've had success with them though in a couple ways While the knob is off, turn the set screw to the minimum depth needed to hold the…
Celestial BCAR but with the mount adjusted to fit snugly into a Lynx and be secured by the pin. Existed before in the original files, but in very limited configurations. It just seemed a little moot at the time since a standard lynx is…
Attach a cleat and hang containers where you need them to keep yourself organised. Centre key on the cleat locks it in place and prevents sideways sliding. Can be used to hang anything from parts containers to picture frames. If you…
This object was made in Tinkercad. Edit it online https://www.tinkercad.com/things/j4mshWYzBS2 Added a "D" keyed hole for the USB-C entry, and changes the right-most port to accept a HDMI connector. Print instructions Category: 3D…
(UPDATED 096-06-2020) Created a smaller version that still fits perfectly. Tried the others but would not work with My Emax Hawk 5, with a capacitor. So I went to Fusion 360 and modeled this up. Fits like a glove. Everything is keyed, and…
Fuddled my way through Fusion 360 to make a keyed rotary switch for my Schumacher Battery Charger. This also fits my crockpot, so it might fit a bunch of things. I printed mine with fuzzy mode, and didn't remove the support in the arrow,…
Reduce an inside-threaded sleeve to a smaller one with inside keyed for insertion and removal. The example shows an M8 threaded sleeve which will be used with an M5 bolt to hold a fixture. More sizes and lengths can be added if requested.
Magic: The Gathering Commander Deck Cube 100 Card – Keyed Tabs with Magnetic Snap Closure At first glance, it’s deceptively simple - a smooth black base capped with a translucent green shell, perfectly cubic, perfectly balanced. But like…
Not a direct derivative, but similar to: http://www.thingiverse.com/thing:5551 I have found there are many times when I want to connect one piece of something to another. Having a generic trapezoidal key and slot system goes well for such…
Fits perfectly on the keyed tube of a Lux Royal vacuum cleaner and other cleaners with a similar profile. Print tested in ASA and ABS.
This is a slightly scaled up volume wheel for AudioEngine A2+'s that have Micro usb in stead of the USB type B.
A stylized chibi garage kit of Malfoid in her classy "ohoho" smug pose, sculpted from scratch in Blender. Created with the blessing of the original concept artist, Pakprof (@pakprofpoke on twitter). Model Features: - 9 Separate Parts:…
This is a small-bed remix of RobC’s “Accessory Rail for Ryobi Link” v4. The rail is supplied as left and right STL files. Each section fits on a Creality Ender 3 V3 KE bed; assembled, they retain the original rail’s 274 mm overall length.…
This is a replacement rotating knob for a traditional food mill, also known in Italian as a “passaverdura”. I designed this part to repair a food mill with a broken or missing handle knob. It is a simple functional replacement part, but…
Fit tightly to the inside of a lynx muzzle and keyed for 40cm. Alternatives provided if your barrel pushes the notch too far forward (marked as the tenths of a mm it's moved).
Celestial BCAR but with the mount adjusted to fit snugly into a Lynx and be secured by the pin. Existed before in the original files, but in very limited configurations. It just seemed a little moot at the time since a standard lynx is…
Designed to raise a pot off the ground slightly while remaining discrete and being adaptable to multiple sizes. smallest size is 15cm or 5.75in. Legs can add 10.5cm or ~4.25in in length to either side of that making a maximum width of…
I have need to attach some notched things to a shelf. This thing is a UClip, similar to this set of things: http://www.thingiverse.com/thing:5208 It has the standard Key on the edge of it, so that you can attach something, or a number of…
