Counting matching models…
NOTES: 3D printing isn't a food safe process, filaments have unknown additives and colouring chemicals, brass nozzles can contain lead, and layer lines are shown to trap bacteria and cannot be adequately cleaned; as such this design is…
Water Dispenser lever for KitchenAid and other fridges This lever allows for dispensing of crisp cold water using one hand. Tested on KitchenAid model KBFS22EWMS but the same model is branded under Whirlpool and Frigidaire. Bracket part…
This is a remix of the KitchenAid stand mixer shield and funnel for mixers with the 6-quart bowl (Model KP26M9PCCU but should fit other 6QT units). Both parts are resized equally so that the shield is now 243mm wide. The shield and funnel…
The holes are sized for #8 wood screws. Designed to only need supports for the large hole in the rear. Printed with 10% infill.
KitchenAid Stand Mixer attachment hanger, remixed to have hexagons on the base to stop the posts spinning.
After several dropping accidents, the original "pusher" for my Kitchenaid 5KSMVSA Fresh Prep Slicer and Shredder attachment exploded. Like many of these things, finding a replacement part without buying the whole she-bang again is a…
NOTES: 3D printing isn't a food safe process, filaments have unknown additives and colouring chemicals, brass nozzles can contain lead, and layer lines are shown to trap bacteria and cannot be adequately cleaned; as such this design is…
A remixed model. A KitchenAid mixer attachment hanger. Either screw it in or use double sided tape.
Kitchen Aid attachment under cabinet mount, printed using Polymaker Polyterra PLA+ at .16 layer height and 25% infill.
I recommend a high infill and a robust material that will hold up. Please note the picture is the old version. The stl is a newer more robust version.
See my improved version 2 here ! ---------------------- Here is a clever, sleek storage solution for a stand mixer’s attachments—each piece is suspended like a kitchen gadget display! All mount neatly under a shelf and ready for action,…
Mount your paddles, whisks, and dough hooks under a cabinet or shelf for easier use and storage! Designed around using a command strip to attach the holders under a cabinet. Note: not every surface will do well with command strips. double…
Made for Kitchenaid refrigerator KRFC704FPS05 but may work for other models these spacers were made to achieve spacing to fit two pyrex dishes without interference to an upper shelf. Print one spacer for each of the four corner supports.
I printed out of PETG, flat on the build plate as the model is oriented, no supports - seems to work OK on the overhangs.
There's a known quality issue with Kitchenaid stoves where the chrome on the knobs flake off after some time. This design replaces chrome plated knob with your own material.
This model is for a replacement foot for KitchenAid food processor model number: KFP600OB. The original feet are rubber and thus are a bit more flexible, but this will keep the food processor level functional as if it were the original…
After printing it just slide it on the mill and enjoy. The adapter is very precise in size to hold on to the machine, slide it as straight as possible. Print Settings Infill: 0% (Vase MODE) Print it as a single perimeter wall 0.35mm (vase…
This is a very simple replacement knob for the KitchenAid stand mixer. I expect this to fit multiple mixers, however, it is designed to resemble the OEM part from my bowl lift stand mixer. If you use this part for a different stand mixer…
KitchenAid Professional 600 Cord Holder. Place to coil up the cord instead of wrapping it around the neck of the mixer. Prints as 3 pieces, no supports required. Any filament can be used. Uses 2 M3 20 Hex heads to assemble. Base piece can…
Kitchenaid Pasta roller attachement storage helper. I created this to be able to store the pasta roller efficiently near my kitchenaid. v1 is the one on the pictures. v2 ATTENTION! This is not tested! I improved v1 to make it a bit…
I modified the original model to have a stronger fillet at the base of the pole to improve solidity
KitchenAid Pasta press tagliatelle form Print instructions Category: Kitchen & Dining
gears that fit inside the pasta attachment for the KitcheanAid, the are a tight fit in the roller shafts (no glue needed). designed in FreeCAD, I used PTEG for strengths , they have held pretty well so fare after a few months of use.
An FDM printable wall mounted hook for hanging a kitchenaid pour guide/splash guard thingy on a wall to keep it out of the way! This was just superglue-gel'd to our splash guard, but I've included the f3d file in case you want to modify…
This is not the only model like this by any means, but I made one too! Mine has a screw hole through the central post in case you need to screw it into whatever you're attaching it to, but we found that with a good blob of superglue gel…
Intended to be mounted under kitchen cabinet for storing mixer attachments. Secured with 2 screws. Intended to be printed on its side with supports.
Redesign of the KitchenAid Attachment Hook w/o the need for support (faster, less material). Thanks for sharing! Easy print with common materials and layer heights.
If you have lost your front cover, this is now the opportunity to simply print a new one. Wenn sie ihren Frontdeckel verloren haben, ist das jetzt die Möglichkeit sich einfach einen neuen zu drucken. Printed in PLA - 100% Infill
Water Dispenser lever for KitchenAid and other fridges This lever allows for dispensing of crisp cold water using one hand. Tested on KitchenAid model KBFS22EWMS but the same model is branded under Whirlpool and Frigidaire. Bracket part…
A friend requested a cover for her KitchenAid. Don't know which model, the photo should make it clear.
If you don't know, you can replace parts of your Kitchenaid mixer including the metal gears, motor, main board etc. I was replacing some of my gears and noticed that the grease in the gear box had leaked into the motor. I found that the…
I killed 2/3 pasta rollers in my set, which prevented me from making pasta. Well, it didn't, but it was really annoying to do by hand, and it meant I could only have fettucine. So I designed a new shaft for these - it should be…
This extended splash guard is designed for 3-liter KitchenAid mixing bowls , providing extra height to minimize splatter when mixing larger batches. The extension seamlessly fits onto the original bowl and works with the standard…
Stores two pasta cutting attachments for your KitchenAid. It's tight enough to prevent them from falling over e.g. in a deep drawer.
This is a remix project for Kitchenaid tools's hanger for IKEA KUNGSFORS. The print settings are preatty straight forward and you need supports under the curvature and the little knot on the underside part. You'll need a couple of M4 10mm…
A simple method of storing the standard Kitchenaid mixer whisk, dough hook, and paddle when not in use. Ideal for renters, this is made to mount with removable 3M strips. Use PETG or ABS for best results. PLA might work, but I haven't…
Needed something to put over a pizza cutter so it can be stored in the drawer. Modified pizza cutter cover by theKen to fit the KitchenAid Classic Pizza Cutter. Using 12x3mm neodymium magnets to attach…
You will need a M3x30mm bolt and a M3 nut to insert in it. It can be installed with M4 or M3 wood screws. Printed on MK4s 4 perimeters 0.2mm PETG Organic support on the build plate
Inspired by https://www.thingiverse.com/thing:4682298 OEM Part: https://www.whirlpoolparts.com/PartDetail/Dispenser-Tray/WP2206670B/826974 Our refrigerator's drip tray was starting to show its age, and had calcium deposits that were…
Snap-on spout for KitchenAid coffee grinder/mill for directed stream of coffee grounds into a measuring cup for less mess. 2 different spout lengths - SHORT ver. is 1", LONG ver. is 1.5" Printing Instructions: 10% infill Minimal supports…
4-way holder for Kitchenaid espresso machine portafilter. The part is made of 2 pieces so that the ABS doesn't warp on the print bed. Also works with other 58mm portafilters. Supports are needed.
A long time ago my dad misplaced the original jar that came with our KitchenAid Burr Coffee Grinder. When he finally bought a new one he gave me the old one, and I modeled this in TinkerCAD so I didn't have to use ZipLock bags anymore.…
KitchenAid Lid, to fit nicely on the Artisan. it prints with minimal support in petg. ( see pic ) Happy printing Print Settings Printer Brand: Prusa Printer: I3 MK3S **Rafts:** No Supports: Yes **Resolution:** 0.12 Infill: 20%…
My knob broke and I needed another. It is modeled closely to the original. Print oriented flat on your build plate (no supports required) and enjoy new life from your convection toaster oven!
The pins holding the weeks of my dishwasher's lower rack starting coming out recently, and before I could fix it I lost some of those wheels. I only had PETG filament to play with, which tended to soften in the dishwasher, and so I went…
This is a replacement foot for the KitchenAid K45SS Stand Mixer. It was printed using Ninja Flex using the Generic Flex profile with a .60 nozzle. I added a 4x18mm flange to the base to allow more of the mixers frame to contact the foot.
Replacement dial for KitchenAid digital scale. They sell a lot of different scales, so I'm not sure which exact model this one is (see images). Prints without supports. Make sure to give enough infill for a strong connection with the…
Druck mit PETG oder PLA, 15% Infill, 0,2 mm Layer. 23.08.2025: Neue Version (durch zusätzlichen Haltering innen stabilere Befestigung)
Replacement Stove knobs for my KitchenAid Oven after my dog chewed up the originals. If you need a knob you can check the attached photos of the original and this replacement to see if yours matches. Print instructions Category:…
Rounded off the corners to more closely match the original stove knob. Print instructions Category: Replacement Parts Print Settings Printer: Da Vinci Pro 1.0 Rafts: No Supports: No Resolution: .02 Infill: 20%
The previous shelf broke, so I modeled and printed a new one. Works great in white PLA.
I made this last year to replace the original gear that broke on the rail of my freezer drawer since I was unable to find the part online without purchasing the complete rail. My fridge is the KitchenAid /Whirlpool (W10772358) five door…
I made different Models for differnt attachments. I used the one for Two-sided tape. In my case the strongest from Tesa.
The Kitchenaid Pasta roller attachment is useful but after time is gets dirty and the temptation is to put a rag or other object in to clean the rollers whilst its running. This can lead to a jam and to stop the main machine self…
A small holder/base to hold your KitchenAid Immersion Blender upright on a counter!
This is a replacement knob for a KitchenAid Model 4C vintage stand mixer. Design file available here in Onshape: https://cad.onshape.com/documents/96b6378f5ed2e6a7ceada73e
Turn Any Bowl into a KitchenAid 5qt Mixer Bowl Tired of expensive replacements? My original glass bowl cracked at the base and wobbled during mixing. Instead of spending $40 on a new one, I designed and 3D printed this simple adapter that…
This part broke on my microwave and a replacement is about ~$60 here in Canada (slightly cheaper if if I order it from the US). I decided I would print my own, and hopefully others can use this as well. My microwave is a KCMS1555RSS but…
When I was newer at 3D printing, I printed this under-cabinet KitchenAid accessory holder I found on MakerWorld. But the spacing was tight. I had to flex pieces to make them fit. Which led to broken pegs. So I remixed the model a bit to…
Our Kitchen Aid 6.5Q didn't come with a handle so I decided to make one. You can either scale for a pressure fit or you can glue it like I did.
This design is for a replacement foot to your Kitchen Aid mixer, ensuring stability and preventing scratches on your countertop. The design features a good fit for easy installation and is compatible with various Kitchen Aid models.…
Uses the screw in the back that holds the metal rim in place. May fit on other bowl lift stand mixers but not tested. No supports needed print with .4 nozzle can be printed in pla, petg or tpu(when using tpu do not wrap cord as tightly or…
I designed this wheel and pin as a direct replacement for the lower tray wheel on my Kitchenaid washer. This part MUST be printed in ABS or a similarly heat resistant filament, or it will deform and melt from the hea inside the washer.…
Just a hanger for kitchenaid mixer attachments. You'll need #6 countersunk screws to install them. (I only had #8 screws on hand so the screw heads are sitting a bit proud in the photo) Edit: added the step file for anyone who wants to…
Small stand for the KitchenAid pasta roller. Tried to keep filament cost as low as possible. Has a good grip and wont fall over if you tip it. Print with 10% infill. No support.
Inspired by llamboladd's Spinning Daisy found on Thingiverse https://www.thingiverse.com/thing:5229296 I modified Jozarth's static prop into a spinning prop. This completes the military aircraft theme of the mixer. Shaft and prop were…
Not much to say. I had a broken lift arm component. I'm told it's because my wife lifts it from the cupboard by the bowl lift mechansim, but I suspect it's actually from someone forcing the lift mechanism backwards or lifting the machine…
Dishwasher wheels for an older model KitchenAid. If your wheels are supposed to hook onto a steel loop maybe these wheels will work for you. Print the hook part at 45° for better layer adhesion.
Left propeller for the KitchenAid mixer attachment hub.
This is a simple hanger for mouting wherever you'd like to store those unused KitchenAid attachments so they are FINALLY out of your way. (Good grief I've been fighting these things for a year just to get to the toaster!) Also, use this…
The top rack adjuster assembly (part WPW10546503 ) on several models of KitchenAid, Whirlpool, and Kenmore dishwashers is highly loaded and very underbuilt. I designed these snap-fit adjusters to replace the factory parts. They are…
A simple splash guard/lid for the KitchenAid bread baking pot. The first two parts can simply be glued together. inspired by: KitchenAid shield with attachable funnel by Heiti - Thingiverse
holder for the 3 pc past roller by Kitchenaid, strong and low filament amount needed for its size. PLA, 10% infill cubic
Made a simple wrench for the accessory knob on our mixer. It's a snug fit so scale to fit your preferred tightness. Designed for KitchenAid Artisan series but may fit other models. Note: Images shown are on a 0.8mm nozzle so it will print…
A simple wall mount for the 3-piece Kitchenaid Pasta Roller & Cutter Set.A simple wall mount for the 3-piece Kitchenaid Pasta Roller & Cutter Set to maximize space in my cabinet and keep them organized. I have included two STL files, one…
A simple and easy to print stand to hold the 4 standard Kitchenaid bowl-lift or 3 head-tilt mixer attachments upright. Saves some space and keeps them organized. The head-tilt models come with a different dough hook that requires more…
Meine Frau mochte den Deckel der Kitchenaid Glasschüssel nicht da er schlimm nach Plastik stank… Auch nach über 4 Jahren stinkt er immer noch zum Himmel - also mal “eben” ein Neuen aus PETG Drucken… Sollte am besten mit PLA als Interface…
I printed it with PLA. If I had to do it again, I would print it in PETG for a little more flex, but PLA works just fine. The design can warp, so you need to be careful with ambient temperatures and moving air while you print. I…
This lid protects your fingers from the sharp blades of the blade assembly which comes with the KitchenAid blender's jar sets. It can be printed without support. I printed it with PETG.
Happy Thanksgiving - Make those Holiday Recipes with ease with this Easy to add dry ingredient funnel to your mixing bowl while the mixer is running (or not). This offset funnel has a tool accessory post to mount onto the KitchenAid…
This is a simple device for hanging your hand immersion blender, either corded or uncorded inside your kitchen cabinet. It is composed of two parts so that the hanger part can be easily remove and replaced. In this case, it fits the…
A useful shaped funnel that holds approximately 800 grams for a Mochmill
Attaches to your kitchenaid mixer using the existing screw on the back. Remixed to allow the cable to snap in securely.
This is a remix from the excellent repro of OnShape https://www.thingiverse.com/thing:2036688 I read the comment from Refrigiraider and decided to add three holes of 3.5mm. I screwed 3 M4X20 in it and it fits perfectly. I also add 0.2…
This is an extended shelf support for my parents older KitchenAid freezer. It also ended up working with my Aunt's freezer. The OEM supports are too short to adequately support the shelves in the freezer (I assume this is more true when…
This model prints without supports with a print-in-place sleeve bearing. Force the part onto the metal handle of a K5A KitchenAid mixer or maybe other mixer models that lack a handle. The outer section should separate from the inside…
This printable cord wrap is designed specifically for the KitchenAid Professional 600 Series stand mixers, including the KP26M9XCOB and other 6‑quart bowl‑lift models with the same rear housing shape. The mount attaches to the back of the…
Layer height 0.2, no support except for brim. Uses original screws. Looks very natural on the machine! Not like the glue on cable holders
My KitchenAid icemaker no longer rotates when you use the ice lever. The teeth on the icemaker that spin the rotating mixer no longer latch on to the hex nut that connects to the freezer. This "snugs" up the teeth on the ice container to…
This is a remix of the KitchenAid stand mixer shield and funnel for mixers with the 6-quart bowl (Model KP26M9PCCU but should fit other 6QT units). Both parts are resized equally so that the shield is now 243mm wide. The shield and funnel…
Simple stand with 3 slots that perfectly fits your kitchenaid dough hook, whisk and paddle attachments. Optional but I suggest adding some self-adhesive rubber feet at the bottom to stop it from sliding. Thank you! If you wish to show…
An STL of the KitchenAid mixer gasket on models like the KSM-90. Print in flexible filament, I used 3D Solutech's clear flex which (I think) is 92 or 98A. Softer materials like Ninjaflex should also be fine, you need something with a…
Here is a small print for those KitchenAid Mixer attachments. I printed the two halves flat side down as printing long skinny parts vertically never seems to work well for me. Remixed to add screw holes and alignment sockets. No need to…
The holes are sized for #8 wood screws. Designed to only need supports for the large hole in the rear. Printed with 10% infill.
KitchenAid Stand Mixer attachment hanger, remixed to have hexagons on the base to stop the posts spinning.
