Counting matching models…
I always had problems with my Kratky bottles. Either, they were super hard to refill, or the plant just dropped into the vessel. This adapter fixes that! You can just easily fill the nutrient solution into the funnel, and it will flow…
A ktratky system (passive hydroponic) to go into any bottle of 75cl or less capacity.
I always had problems with my Kratky bottles. Either, they were super hard to refill, or the plant just dropped into the vessel. This adapter fixes that! You can just easily fill the nutrient solution into the funnel, and it will flow…
This is a blackout sleeve and cover for 32oz mason jars, for use with Kratky hydroponics. The sleeve blocks light to prevent algea growth. The sleeve fits loosely so the plant can be lifted out to check nutrient levels easily. The cover…
Using the container for a Kratky setup. I wanted to put more nutrient solution in the container but the holes prevented that so these are plugs for the holes. Specifically for these Sterilite Stacker Totes, I use the 4 gallon version but…
My original Kratky model used canning lids that are made of metal. After a few uses they tend to rust. Luckily I found a regular mouth jar lid here on printables and modified it to add the rockwool cube holder.
Green Onion Mason Jar Station! tired of buying and buying? time to start growing instead! simply chop the bases off the onions and stick them inside a jar of water (with nutrients). they dont need much light and are very hardy. made for…
Lid for 4.75 inch flowerpot(from Dollar Tree) with integrated 25mm net cup and covered fill port. Should be good enough for leaf lettuce or herbs
This is a simple model that prints with about 8g of filament, without supports. Print with the flat side down, .20mm layers, 4 walls, no supports. Fits up to 9 on a 210x210 plate. The holder for the rockwool cube does not have a bottom,…
Simplify your hydroponic setup with our custom-designed Kratky lid for the 800g Taco Jar! Perfect for the Kratky method, this design makes it easy to create a stable and functional hydroponic growing system at home. The lid fits a 70mm…
Combine aesthetics and functionality with this 3D printed cover and lid for quart-sized wide-mouth Ball mason jars. Ideal for DWC and Kratky hydroponics, this model not only adds a decorative touch but also provides practical features…
Mark above the flower shows where the net pot ends, the one below the flower is a guide for the nutrient solution level.
I wanted a 3D print to hold up plants in a 5 gallon bucket. I started with a base that I can insert a 2" net pod and then I created inserts that hold up the plant a few inches up. The base is in two pieces that snap together after you…
I created these with Tinker Cad, you can use these to transfer your Gardyn Y-cubes to jars to use with the Kratky style of hydroponics. Kratky is a method of simply adding nutrient solution to the bottom of the netcup (or in our case the…
Another Kratky solution for establishing root systems before moving plants into a hydroponic grow tower. Well established root systems are required for successful plants! This time, a simple Mason Ball jar lid adapter that replaces the…
This is a modular tray system that allows plants to establish root systems via a Kratky growing method. This allows users to bring struggling plants inside or into a more gentle environment under high intensity grow lights should they…
This is part of a series of Kratky hydroponic pots and lids. The wall size is specifically designed for a .8mm nozzle with .8mm wide extrusion for fast printing. It was printed hot in PETG. This fits a random metal bucket I found. It…
This is part of a series of Kratky hydroponic pots and lids. The wall size is specifically designed for a .8mm nozzle with .8mm wide extrusion for fast printing. It was printed hot in PETG. This is a random plastic bucket I found that was…
This is part of a series of Kratky hydroponic pots and lids. The wall size is specifically designed for a .8mm nozzle with .8mm wide extrusion for fast printing. It was printed hot in PETG. As the name says, a cover for a hole left where…
This is part of a series of Kratky hydroponic pots and lids. The wall size is specifically designed for a .8mm nozzle with .8mm wide extrusion for fast printing. It was printed hot in PETG. This is a random plastic bucket I found that was…
This is part of a series of Kratky hydroponic pots and lids. The wall size is specifically designed for a .8mm nozzle with .8mm wide extrusion for fast printing. It was printed hot in PETG. This one holds one AeroGarden pod but is…
This is part of a series of Kratky hydroponic pots and lids. The wall size is specifically designed for a .8mm nozzle with .8mm wide extrusion for fast printing. It was printed hot in PETG. This one holds one four inch net pot. The basic…
This is part of a series of Kratky hydroponic pots and lids. The wall size is specifically designed for a .8mm nozzle with .8mm wide extrusion for fast printing. It was printed hot in PETG. This one holds three inch Aerogarden pods or…
This is part of a series of Kratky hydroponic pots and lids. The wall size is specifically designed for a .8mm nozzle with .8mm wide extrusion for fast printing. It was printed hot in PETG. This one holds one three inch net pot. The basic…
This is part of a series of Kratky hydroponic pots and lids. The wall size is specifically designed for a .8mm nozzle with .8mm wide extrusion for fast printing. It was printed hot in PETG. The basic outer shell is intended to use a 2…
A ktratky system (passive hydroponic) to go into any bottle of 75cl or less capacity.
These are small plastic parts for easy growing of Kratky hydroponics plants in plastic bottles. I include three sizes: for narrow bottle throats (21.4mm inner diameter), wide bottle throats (33.4), and for big 6l bottle throats. If you…
Two funnels, one curved and one straight, that fit my bottle inserts for Kratky hydroponics model, shown in this video: The straight one is just that, but in many cases with a bigger plant you won't be able to fit it around the leaves, so…
This is a functional and modern looking hydroponic vase which can be used for passive hydroponic methods such as Kratky's (or non-circulating/ passive hydroponic). I designed this vase to be fast to print and leak-proof right out of the…
Grow fresh herbs on your windowsill from bottles you'd otherwise recycle. This set turns an ordinary PET drink bottle into a passive hydroponic planter using the Kratky method — you fill the bottle with nutrient solution, drop in the net…
For those that want to grow vegetables, flowers, etc. inside your house using a fertilizer solution/hydroponics. This is a shell(cover), cap, and pod for a Kratky Hydroponics setup. The shell is designed to use a 1/2 gallon BALL Jar with…
This is a larger version of https://www.printables.com/model/87089-mason-jar-hydroponics It's a bit larger so it fits on top of tins and other jars. This is for the Kratky method of hydroponics where the roots are partially in the air and…
A few months ago I saw the #Kratky planting method. Since I wanted to grow the basil for my Neapolitan pizzas myself, I had to try it out right away and started with some tinfoil-wrapped mason jars . That worked well, but was imho too…
This project provides hole supports to make your DWC or Kratky tote lids a little less hacky looking and even provides a water level indicator without grommets and a see-through pipe. If you're running “Outdoors”, it can also reduce the…
Update 2020/06/23 Adding a rockwool_pebbles_pod.stl file, which is basically the same as the previous rockwool_pod.stl but now you can put some clay pebbles at the top to keep the plant straight. I noticed it was necessary after some…
A simple remix of the original. I scaled it down from 3mm to 2mm thick to give the outer ring more thread to hold.
Tray system for IKEA SAMLA boxes (5l or 11l) as nursery of seeds or cuttings / cloning for hydroponic propagation. The nursery makes already use of the final pots meant for example for the hydroponic tower. It holds up to 6 of the…
Simple, friction-fit lid for regular mouth mason jar lids. This will secure a 2" net pot to a regular mouth mason jar lid, and allow you to unscrew the whole contraption together for refills. I printed these with a 0.8mm nozzle for one…
The original model did not work with a 1.9L/64oz Mason jar. This fits snug, so it won't slide off. Print body in vase mode
https://youtube.com/shorts/-M8ch4d2bds?feature=share Rockwool Starter cubes: https://amzn.to/45pvu8w eSun PLA+ Filament: https://amzn.to/3BL3You Help support the channel by making purchases through the above Amazon links. As an Amazon…
Kratky holder for the small trofast buckets from Ikea. I used it while transporting plants from the garden after removing soil to the room where the tower is in and to give the seedlings time to grow bigger roots. Designed and printed…
The original print was for wide mouth jars, this remix is for regular mouth (2 ³⁄8″ for the inner diameter and 2¾” for the outer diameter), print diameter is 67mm. The original was a 2 piece print, this re-mix is one piece. The original…
The original print was for wide mouth jars, this remix is for regular mouth (2 ³⁄8″ for the inner diameter and 2¾” for the outer diameter), print diameter is 67mm. Pod holds seed starting medium (coconut fiber, perlite or vermiculite).…
This lid allows you to reuse an old Pot Noodle container as a pot for growing plants using the kratky method. The hole is 32mm to fit a net pot, the ones I bought were described as 1.5" pots. There is a small ridge so it clicks around the…
A tiny funnel that is printed in Vase mode, without top or bottom. In Cura, it's enough to set Surface Mode to ‘Surface’. In other slicers you might have to manually set top and bottom to zero. I printed with 0.6mm wide lines; wider lines…
Print it in a darker color to block light, filament type should not matter Print Stats: ~42m, ~9.9g of filament ($0.15) For the mini-cube netcups and their adaptor: https://www.prusaprinters.org/prints/60181-75-rockwool-mini-cube-netcup…
What's in the files: - a reusable press fit lid - an optional LED grow light mount (V2 is tighter than V1)
a simple adapter to convert a mason jar into a kratky hydroponic setup. 2inch net cup and 1inch~ aerogarden clone standard mason jar
Deep Water Culture (DWC) / Kratky Netcup Plates with refill window, used to turn existing flower pots into self-watering basil and lettuce. Printed in PLA for indoor use, at 15% infill, allows you to drop a netcup, add an air-line, and…
Modular Kratky Hydroponic Planters , designed for enthusiasts and eco-conscious gardeners alike. These planters are specifically crafted to cultivate small houseplants and herbs, adding a touch of green to your living space or kitchen.…
Maximize your growing space with our innovative Corner-Mounted Modular Kratky Hydroponic Wall Planter. This space-saving design is perfect for those looking to bring a bit of nature indoors without sacrificing floor space. Its sleek,…
A cover for 222mL aluminum can avocado seed holder.
A simple lid with a net cup for a WECK (Sturzglas 850 ml (3/4 Liter) RR100 ). Use it to grow herbs in your kitchen. Use a growing medium. I use coconut grow medium pellets (35mm diameter). To avoid algae, use a non-transparent glass. (I…
Hydroponic baskets for 33Cl can long and large version. Perfect for growing aromatic plants indoors.
I use 27mm X 20mm diameter rock wool cylinder that I find here: https://www.amazon.fr/dp/B0B63P94P7?psc=1&ref=ppx_yo2ov_dt_b_product_details
These parts are designed to use a few solid layers on the bottom and then a continuous and unbroken profile all the way up the part. Prusa and Slic3r call this vase mode, while Cura calls it spiralize. I watch Hoocho on Youtube and they…
Lid with a integrated netcup for use with Trader Joe's Apple Cider bottles (or other 40mm lid, twin threaded containers) Category: Outdoor & Garden
Lid that should fit on whey containers with 120mm ID lid Google Kratky non circulated hydroponics for usage details has not been tested with plants, whey container might be too short to let significant air roots to develop (might just…
The 40-liter white bucket from Hornbach is used for the Kratky hydroponic method to grow tomatoes. Tomato plants need support, and the Spiral Plant Supports 170 Galvanized Steel W9Q6 are often used for this purpose in soil. However, these…
I wanted a pot i could see the water level without letting a lot of light in. This works out cheaper and better than mason jars. It only requires a small piece(13cm) of ¼ inch id tubing, for the water level indicator, and a 2 inch or 50mm…
This is the same as this 40oz version just larger so you can get the description there. https://www.printables.com/model/897855-40oz-kratky-hydroponic-pot-with-water-level-indica There are 4 different container heights; 100mm, 150mm,…
These are 2.5 gallon bucket tops for kratky style hydroponics. the design is similar to my original 40oz pots https://www.printables.com/model/897855-40oz-kratky-hydroponic-pot-with-water-level-indica. There are several lid options for…
Filaments can be used such as PETG but then you might need to add some coating inside the resevoir to prevent the water from leaking. But I printed mine in PLA, and i have no leaking, so i would recommend to print the base “resevoir” in…
the vase should be around 126 mm diameter and conical I think is a nice way to have hydroponic plants at home that also decorates home
I use Cz Garden's 2" net pots: https://www.amazon.com/dp/B073WJFHQH?ref=ppx_yo2ov_dt_b_fed_asin_title Has an inner diameter of 53mm and an outer lip so it doesn't move too much over the top of the mason jar. Printed in PETG.
