Counting matching models…
A Mitsubishi L200 2009 model car that you can print along with the tires. The tires were one of my ideas to add to this model car where it can rotate, and front wheels will be able to swivel that linked to the other side. Use filament,…
This is a model of Mitsubishi L200 2009 pickup truck model that I modeled to be 3d printed. Sorry there are no tires modeled for this particular 3d file, the client ghosted me after its completion, hence I somewhat abandoned this. If I…
The following PDF contains custom settings that work better than the default profile included with the Flashforge Creator 5 and Creator 5 Pro. Most of these settings will also work with the Flashforge AD5X and possibly other printers such…
20mm deep electrical box extension adapter. Application: 20mm thick wall panels with 68mm hole
Anschlagwinkel 200mm. Anschlagplatte wird mittels Ruthex Gewindeeinsätze M3 und Zylinderschraube M3x8 befestigt
This is the pinnacle of my tire designs for the robotmover. This tire wont get stuck, rip up your edges or clog up with dirt. Tire is 20mm wide, but use the slicer to extend to 40mm. Printed on CR10s PRO with microswiss directdrive. Rim…
Shift knob is from a 2002 MAN L2000 PhoeniX Campingcar with a 6 shift Eaton-Gear. Label is lasered on 1,5mm signmaterial on a Mr. Beam Lasercutter. Final Knob is finished with filler and glossy black spraypaint. Very special sparepart -…
Prevent the automower from digging ruts in your lawn. Printable on a 220mm square bed. This is a remix of a excelent design by polandmet so that it would print on my 220X220mm bed. https://youtu.be/YmMLucwmtG8 Each wheel prints in 4 parts…
A wrench that you can use for your Hayward CL200 Series Chlorinator, make it's much easier to remove the cap. I printed this with PLA on a printer with a 300mm x 300mm bed. I had to rotate the print 45 degrees to get it to fit the bed. I…
After the wheels fell off by L2000 Worx Landroid I redesigned the wheels to ones which I believe are better. Watch video for assembly instructions.
Stand for Geekvape L200 Prevents mod to fall down when keeping it on table. Cutout in the front where you can see display of the mod.
Only tested on 2019 model, but I think they should work on 2020 model too. The wide rubber stock wheels of the Ambrogio L15 caused too much 'matting' on my young lawn, with very visible tracks and poor mowing performance as the the mower…
A cap for Nikon EN-EL20a batteries to protect the contacts.
A rim and tire / wheel for Worx landroid L2000. Got tires of the original wheel constantly ripping up the grass when doing tight turns. These tires / wheels are have inspiration of tanks tracks. they work great. Try yourself to see what…
This is something i did for my Fosi Audio BL20C AMP to mount under my desk.
I've built this model to mount a Camera into my Mercedes Benz CL203 (Mercedes Benz C Class sport coupe from 2003). Long Story short: I bought a radio and a Camera specifically for my car but ended up ordering a W203 by mistake (it seems…
Update 17 Jan 2023 I got a better result with ABS by rotating it 90 degrees on the build plate and used Paint on support blocking in for holes etc to allow easier support clean up and align the layers to get better strength into the…
Design description This is a gridfinity holder for 2 Nikon EN-EL20 batteries. Block area is 1x1, and has a height of ⅔, not stackable when filled. Gridfinity description Maker-favorite screwdriver storage blocks for the Gridfinity modular…
Einfach druckende Endkappe für den Kabelkanal. Wird mit der kleinen Nase einfach aufgesteckt.
Maybe with stronger filament, they would be more solid.
You need 3 brass M4 inserts and generic 35x18mm titanium coated blades compatible with husqvarna. Also 4 M4 bolts (20-25mm) to mount the disc. I print the base in PETG, though PLA will probably work too. The cover ideally in…
This model allows a Giant Recon TL200 Tail light (and should work also for a TL100) to fit onto a WTB Silverado Saddle (Medium size). I have 2 variants, one with small hoops to mount a small saddle bag and one without. Update 4th April…
Printed in PLA with 15% infill, still plenty strong enough to hold the power supply.
Larger drinks holders for Mitsubishi L200. V2 is offset to allow more clearance between the edge of the holder and the handbrake. I live in Scotland so think i'll get away with mine being in PLA, if you live anywhere remotely exotic…
I made this model for backing up RPi5's Real Time Clock (RTC). It works with maxell's ML2032 rechargeable coin battery ( https://biz.maxell.com/en/rechargeable_batteries/ml.html ) and 2-pin JST-SH connector with 0.8mm cables. Be careful…
There are 2 adapters in here, one has the standard overhang of the actual plate and the other has this removed. Neither have any of the holes or screws of the actual plate and are designed to be incorporated into your thing. There is a…
This is a replacement front cap for the Sony SEL14TC and SEL20TC lenses. Original caps are hard to find, so I modified a front body cap to fit these teleconverters Prints without supports for easy production Can also be used on a Sony…
The tray in the armrest console of my Mitsubishi L200 (2015) broke, so I made a replacement. Not sure if it would fit in later model. I know this is a bit of a niche project, but maybe someone will find it useful. Material: ASA Nozzle:…
Palm rest for 200-600mm lens Category: Gadgets
sherpa mini mount for wanhao gr2/zortrax l200/wanhao d6. can work to original wanhao carriage, but i also work to a this skinny carriage version for better result on acc e speed. stay tune
I printed it in PETG but it would be preferable to print it in a more resistant material.
10-inch Rack mount for fosi audio BL20C. Additional images coming soon. Edit: Increased size of cutout by 1.5mm in each direction. Previous hole was slightly too small.
Replacement for original L200 elbow rest scale 1/10
I've designed this to use two M2 heat set inserts for the camera PCB and used screws from a laptop screw kit. Two M3 heat set inserts are used like in the original version for the aukey cam. Designed for module WN-L2011.K200L FF, but…
A stand for the Brennenstuhl PL200 LED light: https://www.brennenstuhl.com/de-DE/produkte/led-taschenlampen-handlampen-nachtlichter/led-akku-handleuchte-pl-200-ac-200lm Pictured in neon green TPU ("flexible material" STL) and silver PLA…
Boss (DD-20, OD-20, CE-20, RT-20, RE-20, RC-20, RC-30, SL-20) form factor battery cover. Model is friction fit.
Exact copy of the license plate light for Mitsubishi L200 1997-2006
printed from PET with 80% infill
Simply download and print. Redesigned in Bambu Lab Studio when I printed it on my X1C in BBL PLA.
I love the Dremel drill press by pejvl2000 https://www.printables.com/model/308219-dremel-drill-press but I needed a center finder to assist my aging eyes and hands. This model uses two 5mW line lasers I got from Amazon:…
I needed an adjustable holder for the PL200 so that I could use it as a workshop lamp. In addition to the printed parts, you also need 1 M4 nut and an M4x16 lens head screw ISO 7380-1. The magnet has a diameter of 25mm and is fixed with…
Version 1.00, designed in ROBLOX STUDIO (exported as .OBJ). This needs to be printed with supports, with the middle part face down like in the 3D model preview. If supports are not enabled by default, please enable them! Since I couldn't…
knife holder for my robotic lawn mower . this is the first version. known issues: to much filament used holders are breaking off today 18.04.2018 testrun of V1 with broken holder first run was ok V2 changed to print it in two parts you…
If you have an RL200 & have used it for more than 2 months then you too will know the joys of taking the extruder covers off for the umpteenth time. I got so peeved I merged the two covers to try & make life easier, it did help alot so…
Hayward ISCL Series Automatic Chlorine Feeder replacement cover screw. Fits models CL200 and CL220. Hayward Part Number: CLX200G (item 2 in their exploded parts diagram). This has a 19mm hex and M18x2.5 thread if your trying to compare to…
Kleine Halterung für die Ikea Skadis Lochwand um die Brennenstuhl PL200 LED-Lampe zu befestigen. Gedruckt habe ich es auf einem Creality K1C aus PLA+ mit "tree support" . Small bracket for the Ikea Skadis pegboard to attach the…
A Bahtinov Mask for the ASKAR ACL200L astrophotography lens. I had tested and it works very well, I left a small gap so you can install some felt taper around the inside wall so as not to scratch your telescope. I don't have photos of the…
I had this blinkers laying around but the accessories were not good enough for me as they either impede the back light or would be blocked if anything was on the rear rack.…
Bunlar Mitsubishi L200'ün tavan borularının kapakları. Bunları bir arkadaşımın arabası için yaptım. STL dosyasını paylaşıyorum.
This allows you to mount your Hamulight L2046 power supply wherever you need it instead of having to rely on 3M tape. It will print fine without supports with “mounting ears” in the air because I used counterbore bridges and suitable…
Support to hold the detergent bottle in place when it starts to empty The support can be printed in PLA, PET, PETG... Optional support trees The cap can be printed in Flex TPU (You do not need the cap if you are not filling the detergent…
Work in progress of a coil pack bracket for my Datsun 620, which has an L20B engine. It's designed with a 10 degree cant to help with the “approach” angle to the plugs. It's touching the upper heater hose, I so would recommend adding a…
model made after a picture with hyper3d and the hook + support made by me
Ich habe es mit meinem Alten Creality Ender 3 v1 gedruckt. Es braucht keine Supports und sollte mit einer Geringen Füllung gedruckt werden.
This extra layer of security for your front buttons will protect it from your curious cat walking on it and triggering various functions of the robot, while not having to keep it in child protection mode. Print with anything, flat part on…
The seat adjuster handle (driver’s side) on my Mitsubishi L200 (2015) broke, so I made a replacement. It’s not a replica—just a simple handle that fits onto the metal protrusion. Not sure if it would fit in later model. I know this is a…
Replacement lid for the Fagor ML2006X coffee grinder.
Protect your Sony SEL200600G lens from accidental scratches and edge wear with this custom-designed bumper. This model includes two protective rings : one for the front and one for the rear section of the lens. Designed in Onshape, the…
A comfortable grip for the iShoot foot for the Sony 200-600 telephoto lens. Print standing up on the back plane. No supports required.
Thinkcenter Rackmount for minirack, made compatible with narrow clearance of AL2020 extrustion rack
Universal adapter to third parties soft boxes for GODOX light SL60/SL200 3 walls, 15% infill Cross Hatch. Add a few modifiers to 80% infill as shown on the last photo. I recommend printing from heat-resistant durable materials such as ABS…
Mitsubishi L200 1996-2006 Bull Bar YOU NEED TO SCALE IT TO YOUR NEEDS IN ORDER TO FIT THE ACTUAL CAR . PRINT IN ASA
A holster for the above hard drive that you can stick to the back of your laptop screen
Customized version of http://www.thingiverse.com/thing:1039106 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=1039106 Instructions Using the following options: labelHeight = 20 textStyle = out textFont =…
I've bought this light a while ago to use in my bathroom, but holy crap! It says 900 lumens on the box but upon flipping the switch, I pictured myself in an episode of X-files being abducted by aliens. I decided to print a dimming shield,…
Replacement buttons for the Perodua Kancil (K1-K3)/Daihatsu Mira (L2S/L200S) dashboard clock. Prints without supports.
Print with the front of the plate facing the print bed. Supports required for the two latches (for the bottom side of the DIN mount), though you can modify the provided Fusion 3D/STEP file to round/chamfer this off to print without…
This is a dash insert which fits just below the temperature/climate control knobs. It is sized to fit two standard outlets, and two rocker switches.
for all possible fixtures on GoPro mounts.
A replacement rear housing for the Perodua Kancil (K1-K3)/Daihatsu Mira (L2S/L200S) dashboard clock with faithful and easier-to-print versions. The faithful version requires extensive supports and preserves the look of the side that you…
This extra layer of security for your front buttons will protect it from your curious cat walking on it and triggering various functions of the robot, while not having to keep it in child protection mode. Print with anything, flat part on…
Thinkcenter Rackmount for minirack, made compatible with narrow clearance of AL2020 extrustion rack
Mitsubishi L200 1996-2006 Bull Bar YOU NEED TO SCALE IT TO YOUR NEEDS IN ORDER TO FIT THE ACTUAL CAR . PRINT IN ASA
The tray in the armrest console of my Mitsubishi L200 (2015) broke, so I made a replacement. Not sure if it would fit in later model. I know this is a bit of a niche project, but maybe someone will find it useful. Material: ASA Nozzle:…
The seat adjuster handle (driver’s side) on my Mitsubishi L200 (2015) broke, so I made a replacement. It’s not a replica—just a simple handle that fits onto the metal protrusion. Not sure if it would fit in later model. I know this is a…
This allows you to mount your Hamulight L2046 power supply wherever you need it instead of having to rely on 3M tape. It will print fine without supports with “mounting ears” in the air because I used counterbore bridges and suitable…
Made a model for the tread as the originals get brittle and flake off over time. Printed with TPU. When putting it on make sure to first clean the wheels using sandpaper and then apply a bit of glue and slide the printed parts on.
If you're going to an electric fuel pump on your L20B, this should work. If you plan to print, I think your only choice is probably nylon IF you make sure to properly anneal it . Otherwise, the DXF file is included, which you should be…
Cube_6x6x6_E1_K4_L20 - Peng Song A size 6 cubic puzzle of 4 pieces, rated at level 9 (moves to remove first piece). Adapted from web page: https://sutd-cgl.github.io/supp/Publication/projects/2022-SIGGRAPH-High-LevelPuzzle/index.html ACM…
Beim Drucken von PETG mit Raft unbedingt mit dem Prittstifft auf Texturblech einen Klebe-Trennfilm auftragen. Ansonsten gibt es Probleme beim Lösen! Durch den Schlitz können Sie gut 10 mmbreites RGB-LED Leuchtband von der Stirnseite…
Easy mount for attaching a GoPro to your Sony 200-600 lense. May fit others.
A filament clip that fits the 123-3d.nl spools (1.75mm filament) In 2024 spool dimensions changed! I added a little handle and made it not too small so it is a piece of cake to work with. There are two versions included. Chose the one you…
