Counting matching models…
This is NOT the lighter "Air" frame (yet). This is the standard Pro edition, which can support up to 35mm props (but not HQprop as they are larger). Also keep in mind that the AIO mounting is 26mm and may not work with all whoop style…
Meteor65 Pro Antenna Restrainer Updates [14/02/2024] Rearranged cup direction to produce a flat surface, allowing for easier and better print quality on lower-end printers. See model name (…..revised.stl) Features Prevents the antenna…
Camera mount for the BetaFPV Meteor65 and 75 pro. Gives you 15 degrees of camera angle. This does require a small amount of trimming to the bottom of the camera opening on the canopy. I had great success printing this in PETG. 3 walls…
Designed for vase mode w/ .4 nozzle This is a 550mah Battery Clip for the BetaFPV Meteor65 Pro that usually uses the smaller 300mah batteries. Flexible! Designed to print in vase mode and in PLA. Very light - .6g by filament calculator in…
A sleeve that will clip on to the 300mah Meteor65 battery sleeve, will allow you to use 450mah. I printed it on it's end with the clip opening facing upwards at 15mm's without supports. It's a tight fit to clip it on the 300mah sleeve,…
An antenna support for optimal reception and to prevent it from getting caught in the rear propellers. Insert one of the lobes into the opening on the frame near the antenna. Squeeze the second one together to clear the frame and it…
Meteor65 Landing gear FPV PLA DRAFT work well
Printed with PETG, 0.4mm nozzle, 0.16 layer height
Meteor65 450mh battery holder FPV
I had a mishap when I went to replace the antenna on my Meteor65 pro 2022 version whoop. So I had to replace the VTx, and decided to use a unify pro32 nano. Here's the mount I made for it. It works much better than what I did before……
Print out of hard TPU, like Flexfill 98A. Can probably be printed out of PET as well, but fitting the VTX into the slot might be hard. Longer M1.5 screws are needed for the VTX, but the VTX can also be just slid into the slot and will…
Made this at a 15-20 degree angle includes a space for a zip tie to hold the camera on, I suggest printing on its back with organic/tree supports. I didn't have TPU but I think this would be a good candidate for it. Took me about 40 min…
GNB 530mah Battery Clip for the Betafpv Meteor65 Pro o4 (might fit other whoops)
I made this mount due to the fact that I order the wrong antenna (lol). It's sturdy as is, but if there's any problems, feel free to comment. Note: Inside, you'll have to adjust the cable left or right, to make sure you get a good…
Meteor65 Pro II O4 – Rugged FPV Case 🚁 Everything you need for your Tiny Whoop adventures! I designed this rugged transport case to keep my BETAFPV Meteor65 Pro II O4 , LiPo batteries, and charging equipment organized and protected in one…
Walksnail Avatar HD Nano Camera Mount (TPU Cradle) for BetaFPV Canopy II This TPU mount allows you to adapt the Walksnail Avatar HD Nano Camera V3 (standard 14x14 mm 1S camera, not the Lite version) into the BetaFPV Canopy II (the stock…
Want to run a Walksnail Avatar HD Nano Camera V3 (the standard Walksnail 1S / Mini 1S camera, 14 x 14 mm) in the BetaFPV Canopy II for the DJI O4 Air Unit (Meteor65 Pro II / Meteor75 Pro II)? Here is the problem I ran into, and a fix. The…
