Drill Jig for BetaFPV Canopy II (O4) - Meteor65/75 Pro II - For Walksnail Avatar Nano Camera
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
Drill jig to mount a 14mm Walksnail Avatar Nano V3 / 1S camera in the BetaFPV Canopy II (O4). Parametric Python incl.
- Rating
- 0 / 5
- Likes
- 0
- Downloads
- 2
- Makes
- 0
- Views
- 75
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- RC & Robotics
- License
- Creative Commons — Attribution
Want to run a Walksnail Avatar HD Nano Camera V3 (the standard Walksnail 1S / Mini 1S camera, 14 x 14 mm) in the BetaFPV Canopy II for the DJI O4 Air Unit (Meteor65 Pro II / Meteor75 Pro II)? Here is the problem I ran into, and a fix.
The problem
The Canopy II is made for the DJI O4 / O4 Lite camera. The DJI camera sits in a plastic camera mount, and that mount screws into two arc-shaped tilt slots on each side of the canopy (15-35° tilt).
The camera bay is only 14 mm wide wall-to-wall (BetaFPV spec: "camera installation spacing 14mm").
The Walksnail Avatar HD Nano V3 camera is 14 x 14 x 16.8 mm. It does NOT fit inside the DJI camera mount, and there is no room for adapter walls beside it - the camera alone fills the bay.
The smaller Walksnail 1S Lite camera may fit with adapters, but the standard 1S / Nano camera does not.
The slots don't line up with the camera's side screw holes either: they sit on a 16 mm circle around the tilt pivot, so screwing the camera through a slot puts the lens 8 mm off-centre.
The fix
Mount the camera like any other 14 mm nano camera: one screw per side, through the canopy wall, into the camera's side pins. You need a hole in each wall at the exact pivot centre - this jig gives you that:
Two 2 mm pegs drop into the canopy's existing tilt slots (on the 16 mm slot circle from BetaFPV's drawing).
The guide hole lands exactly on the centre of that circle = the original camera pivot.
Both pegs sit on the same circle, opposite each other, so the hole stays centred even if the jig rotates a little along the arcs.
How to use
Print the jig flat (pegs up). No supports.
Hold it against the OUTSIDE of one canopy side wall with both pegs in the slots.
Drill a 1.5 mm pilot through the guide hole (pin vise / hand drill recommended - the canopy is soft PP).
Repeat on the other side (the same jig works on both walls).
Open both holes to the diameter of your camera's side pins (measure yours, about 2 mm).
Slide the camera in so its side pins seat in the holes and fit the camera's screws from outside.
Set your tilt and tighten. Tilt is friction-held - a drop of threadlocker or a thin washer helps.
Tip: a small piece of double-sided tape or a binder clip on the tab holds the jig hands-free while drilling.
Print settings
PLA or PETG, 0.2 mm layers, 3+ walls. If the pegs are tight in the slots, regenerate with peg_d=1.9.
Parametric - remix it
make_jig.py (Python 3 + manifold3d + trimesh) generates the STL. Every dimension is a parameter:
pip install manifold3d trimesh numpy
python make_jig.py # centred jig (this STL)
python make_jig.py peg_d=1.9 # thinner pegs
python make_jig.py offset=2 # pivot 2 mm toward the canopy front (camera sits further forward)If you make a cradle or a better mount, please post it as a remix.
Notes
Designed from BetaFPV's published Canopy II dimension drawing and tested on my real Canopy II to mount a Walksnail 1S Nano Cam. Test-fit before you drill to be sure, though; your printer's precision levels can cause variations.
Drilling the canopy is permanent (it's a cheap part, but still).