26 models
A quick and dirty miniature approximation of an Ooni Koda pizza oven and pizza peel. My 7-year old daughter requested this, to go with her MGA Miniverse Make It Mini kitchen playset . The scale is appropriate for the epoxy-resin pizza kit…
This thing is a waste of bearings compared to current options. Use this instead Uses either 9 or 15 3x7x3 F683ZZ flanged bearings and 3mm x 14mm pins to assemble. I used Foamgasm's collet and lynx connection and Chance's inline bearing…
Want to access even more models not found here in Prusa Printers? Interested in supporting my efforts making free models for the world to enjoy? Check out my patreon page here: https://www.patreon.com/mz4250 Patrons have access to all my…
Thumb release for ORION Lynx blasters. Parts are set up for right handed users but can be mirrored for left hand use. The mag release lever requires an additional 3/32" diameter trigger pin that can be cut to length; 7/16" [11mm]. Some…
Knurled versions of the Orion Lynx's grip. Includes versions with and without support for the Foamgasm Lynx Thumb Mag Release. Also includes versions with a lynx logo on the butt of the grip. The knurling has been fully redone with clean…
MGA's Miniverse Make It Mini Lifestyle comes with shelves however some of the toys don't actually fit on them. So this is a larger version of what the shelving that comes with the toy so the toys actually fit on it.
This is the 15 degree Foamgasm BCAR adapted to work with the "Ex" screw-on attachment method. It uses the hardware required by Foamgasm rather than what Ex was originally designed with. I made this because I had already purchased…
Requires the Lever & Linkage from the Foamgasm Thumb Magazine Release and one additional trigger pin. Part is created for right hand use but can be mirrored for left hand.…
I made a tire to fit my old model Tonka MGA 1:16 scale. I've "painted" the model when I was about 3 years old, so the paint job isn't great. But I have some memories of this car. Only a few tires were missing (had 1 left) over the 30…
Originally this part was made of steel, then at some point they switched to a plastic unit of nearly the same dimensions. For some decades, if you try to order a replacement you will get a part used on the late MGB, which looks nothing…
This is a custom 3D-printed alignment shim designed specifically for the Mangoal Ford Maverick 4K Dashcam (Model: MGA 032DBA). Its purpose is to correct the factory camera angle, which can otherwise capture an excessive amount of the…
Gas Meter reed holder for Samgas (СамГаз) G4
Baumgartner Bier, Austria's best beer and one of the best beers worldwide. This Logo was used long long time ago, discontinued for many years and almost no merchandise with the old logo available from this time. Made this for an old…
this is a replacement part for the eschbach 440Hz tuning fork usually used in almost every ENT doctors pocket for basic hearing diagnostik. Once it fell on the ground the foot breaks into peaces. the produces does not sell them seperatly…
Removes the slop from the PKI mag release when using the nekomata/foamgasm forward mag release. Make sure to press the linkage firmly into the hole
Just a quick lid for the Heimgart Microgreens Seeder. Works perfetly fine! Two versions available - one with rounded courners and one without.
Chances are if you still own a Commandobot toy from 1999, you're missing most if not all of the missiles. I'm sure they're under a couch somewhere but why bother looking for them when you can just print some new ones! They've been tested…
The following project integrates a Pioneer DDJ-FLX4 into a Magma MGA41100 Carry-lite Case L Category: Audio
Bottom half of the housing from Marcel without ethernet opening
does what it says on the tin, stops the stick from pushing on too far. (as a side note: you can put some heat shrink over the tip of the stick too to avid scratching the paint work in a clumsy moment) LIKE if you like;)
While working on a front suspension rebuild for my 1967 MGB GT, I ordered new trunion dust seals for where the lower trunion meets the A-arms. Even before the car was back on the ground, and not even out of the garage yet, the brand new…
I really like these little memory keyers. They are super handy. They can save 8 memories (4 accessible in each of 2 banks) and have full controls. If you're into CW, go check them out. I have 3 of them. The latest one had an issue with…
Bottom half of the housing from Marcel without ethernet opening
This is a custom 3D-printed alignment shim designed specifically for the Mangoal Ford Maverick 4K Dashcam (Model: MGA 032DBA). Its purpose is to correct the factory camera angle, which can otherwise capture an excessive amount of the…
3D printable topographic miniature of Bremgarten - 🇨🇭 Switzerland Capture the beauty of Bremgarten 's city landscape with this topographic miniature! This 3D model represents the geographic area around the geo coordinates 47.350, 8.344…
