Counting matching models…
The factory gauges in my ‘95 NJ Pajero/Montero didn’t function, so I designed this adapter plate to be able to fit 2" generic gauges in their place. One piece and 2 piece option (uses M3x5x4 heat sets), both benefit from supports, but I…
The standard cup holders in the Mitsubishi PB/PC Challenger are too small for many applications. I made this to fit an insulated coffee mug but it also fits many drink containers.
This is a rough 3d model of interior screw cover for Mitsubishi Pajero/Montero Sport Gen 2 Notes: Mirror the 3d model for the passenger side Use ASA or ABS 100% infil I recommend 0.12 Layer Height
This is a replacement wiper arm pivot cover for the first gen Mitsubishi Montero/Pajero, and Dodge Raider. Made to be a replacement for Mitsubishi p/n MB623853.
Single cup holder that fits where the original ashtray sits. For Mitsubishi Pajero / Montero / Shogun Gen 2.
Add switches to the factory blanked-off places on the dash/console area. ‘Loose’ and ‘snug’ refer to the hole for the switch, not for the plate to dash itself. Scaling up/down a few percent will help fitment in that case if required - I…
Adapter plate to fit DEFI A1 style 60 mm universal sensors in Mitsubishi Pajero 2 in place of factory sensors. Re-uses the screws from the old gauge cluster to mount the new adaptor. This model is based on the use of another model with…
Replacement Switch Plate cover. Designed to fit Gen 3 Mitsubishi Montero (2003-2006), but will likely fit other models. There's a blank version and a version with room for a toggle switch in case you'd like to add one. I've only tested…
This is a temporary replacement cap for the brake fluid reservoir on a Mitsubishi Pajero 4th generation (Montero/Shogun). I suspect this would work for other Mitsubishi cars. I have made this out of ASA, however I believe that brake fluid…
These are the covers for the seat rails, back seat rails, bottom seatbelt cover. In some cases will have to be mirrored. The back(from trunk) covers weren't redesigned, I just figured they were good enough like that(which is not perfect…
cierre guantera central mitsubishi montero, imprimir de forma vertical para que no se rompa, con soporte a la base.
My first detailed model created based on provided measurements, as a request. First version has been printed, but not yet tested. I printed the matching male part from plabs.cz (Thank you!) slightly modified to make rounded part 8mm wide.…
I printed in ASA but anything should work. This is the support for you to use the default vehicle button empty sockets with the ARB or Tyrex compressor or compressor accessory buttons. To install it's important that you do it like this:…
This piece is meant for the sun visor, as it usually breaks. The part is for the left one. You can mirror it for the right side. Should be printed in resin. I use flexible tough from anycubic with great success. I paint it with a mixed…
License Plate Light Housing Backup Camera Mount - Gen 3 Mitsubishi Montero/Pajero/Shogun. Drop-in replacement for the existing license plate plate light housing on a gen3 (2000, 2001, 2002, 2003, 2004, 2005, 2006) Mitsubishi Montero that…
The Mitsubishi Montero and Pajero models use 8-12 2-piece body mounts. Some later models may use 1 or 2 pair of 1-piece body mounts, not covered here. In that case, you can generally retain the original 1-piece bushings and replace the…
I broke the 20 year old clip on the firewall that keeps the throttle body vacuum line from moving around and smacking into stuff. Modeled this clip that fits in the same spot. It should fit as a replacement for other similar clips on the…
This is the square blanking plate for the center console of the Mitsubishi Pajero/Montero 4th generation, with a pre-drilled hole to allow a cable to come through from the inside (up to 5mm in diameter) I printed the plate in PLA+ and…
This is a replacement cord cover for a Mitsubishi work/inspection light from a Gen 2 Montero. Works best when printed with supports and the ribs facing up. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes…
Created a replica of the spark plug retainer for my 03 montero sport, I am sure it will fit other years as well. I printed in TPU 95A, it has been over 6 months since I put them on and so far they are holding up pretty good. I would not…
This is an adapter to use the existing tiny hole to the right of the ignition keyhole for the diff lock button without having to carve anything. I used a very stiff PETG as a regular PETG was not clicking well enough into place(worked but…
This applies to 4M40 model, which should have enough space on the left of the motor housing(right if your vehicle wheel is on the left). The support elevates the compressor and levels it. It is easy to mount with 14mm m6 screws and auto…
Single cup holder that fits where the original ashtray sits. For Mitsubishi Pajero / Montero / Shogun Gen 2.
Created a replica of the spark plug retainer for my 03 montero sport, I am sure it will fit other years as well. I printed in TPU 95A, it has been over 6 months since I put them on and so far they are holding up pretty good. I would not…
