Counting matching models…
Added some extra protection for the front. Made it in the style of TinnierMonster4 's roof skid plate so that matches aesthetically. I've only tested both on the MT10 V2. I used some leftover m3 screws to fasten it.
chain guard for shimano altus fc-mt101 front crank sprocket. best done in petg, but should be ok in pla.
Team Associated Rival MT10 Replacement Wheel Nut Cover
I printed mine in Overture TPU . It's a little squishy but should absorb hits and I never have to worry about breaking it again. 100% infill is probably excessive but I did it anyway. It may work in PETG but I don't know if it will be…
For those running enough power to wheelie an SMT10, here are a couple wheelie bar options. I'm running a 3600 KV brushless with an AX2 2-speed. 3S in high will wheelie or flip instantly. 2S will wheelie on grass, but often just spins on…
Printed in Overture TPU . I've taken it to the skate park a few times and so far it has held up fine. The wheelie bar is optional and no longer adjustable. Being TPU, it is a bit squishy but it works well enough and won't break. I also…
The original part was too wide for my Rival MT10 V2 and it covered the holes for the Body Mounts. So i made it narrower and cut a bit away at the sides. I also cutted something from behind so that it is easier to print on the flat side.…
A FDM printable friendly cap for a 360 prism (MT1000 360 prism or simialr) to replace or repair missing or broken caps. Simply screws on like the original. The FDM printed thread is tight, running it back any forth a few times will…
Team Associated Rival MT10 replacement side Exhaust pipes.
The factory wheels on Axial SMT10 trucks tend to strip the hubs. I tried the epoxy repair method, but it didn't work very well so I created a bolt in replacement hub. This hub is designed for a flat 7mm thick 12mm hex. The factory Axial…
upgraded with alternate shock and sway bar mounts
I managed to break the front cage of my SMT10 when a brick wall jumped out in front of me :-) This is a flat piece modeled to fit the shape of the frame on the front sides to be used as reinforcement. I like the look of the long brace…
Simple holder for MT106 Mr. Hobby Nippers, protects the blade tip. Print settings: no support, 10% infill, 0.2mm
Stylische und stabile Wandaufhängung für 1:10 RC Monstertrucks. Passt für 1:10 Monstertrucks wie Arrma Quake und Rival MT10 vermutlich auch für Arrma Granite, Groom usw. (wurde nicht getestet) Die Schraubenlöcher können abgedeckt werden…
A simple file to center an AMT103-V encoder on a nanotube wheel output. Drill out the mount holes according to the screws you are using. Category: Robotics
The bottom frame holes on the MT10 are different diameters and the left one has added clearance to go around the protruding nut For best results use PETG or better but PLA would also work Layers 0.2 - 0.28 Walls 4 or more Infill 40% or…
Smaller case for Teltonika FMT100. I used inner threads.
This lantern diffuser base is designed to fit flashlights with a housing diameter of 32.4mm, but it can easily be resized to accommodate flashlights with different diameters. Simply plug your flashlight into the top to transform it into a…
This can be used to make a DIY groundsheet with attachment points or a pole base frame. These tents require you to first lay down the inner tent, then build the poles. In rainy water, this results in a wet inner tent. This model allows…
The factory wheels on Axial SMT10 trucks tend to strip the hubs. I tried the epoxy repair method, but it didn't work very well so I created a bolt in replacement hub. This hub is designed for a flat 7mm thick 12mm hex. The factory Axial…
MT10 Body cover tesla truck shape, team assosiated printed with TPU filament, other filaments will break, TPU holds forever. with max parameters 4-5, 100% fill, no support needed for printing, this is the best part for TPU. (top surface…
A replacement front bumper for the Team Associated MT10 V2. Print in TPU and it will be indestructible. The overhangs for this can be a bit tricky with TPU. I went the lazy route and used PLA supports (PLA doesn't stick well to TPU).…
Simple bracket to hold rear body posts on SMT10. post is hold in by 1 screw on each side. I printed in PLA and have bashed without any issues
Clone of rear mounts for the front to mount aftermarket swaybar. I printed in PLA and have had no issues bashing
A connection plate to replace broken part of Camlink CL-MT10 mini tripod.
Axial SMT10 Battery Strap for 38mm 3s Lipo Battery Printed in PA12CF or PA12, 100% infill for Strength Use M3 x 5mm BH Screws instead of self Tappers (No Holes in part to prevent Cracks) Print Settings Rafts: No Supports: Yes Resolution:…
Replacement button for the Meta M99T MT100 keyfob. i printed in PLA with 0.16layer height.
I used Sunlu TPU with supports on and no raft. I printed it at 25% infill and it seemed to work fine. I would recommend flipping the model to print it though.
