Counting matching models…
Update 1: Small optimizations to the casing Added a small groove for lifting the lid Added some space inside on the back for potential cables Hello, here's a small project that I designed. I wanted to combine a small ESP32-C3 Super Mini…
This is a redesign based on the idea and software from Ultimate ESPHome DIY Smart Sensor | fixtSE The individual sensors are clipped in neatly and are not loose in the housing. Printed with PLA, 15 % infill. Electronics used: ESP32 30 PIN…
https://apolloautomation.com/products/msr-2 The ball mount is a remix of: https://www.thingiverse.com/thing:67911 from Gyrobot
Spliced together a few different files to fit my own requirements. You may need to re-size/check the carrier dimensions depending on your own ESP32 board. I designed this to use with Jumper cables, i didn't have a screw for the DHT sensor…
Case for HLK-LD2410C mmWave & D1 mini ESP8266 to be added in a room or to be put on a wall. Material used for printing: PETG
Introduction: This is an ESP32 D1 mini case for temperature and an optional mmWave Radar presence sensor. Optimised for space efficiency and the placement of the temperature sensor has been optimised to minimise self heating from the…
The Apollo Automation R PRO-1 PoE mmWave Multisensor (LD2450 and additional LD2412 add-on option) is our most advanced presence sensor. Designed for power, precision, and reliability, the R PRO-1 is a compact PoE mmWave sensor built for…
This is a print to house a ESP32 D1 Mini board. The case uses a USB plug which can be soldered to the ESP32 board making it able to plug directly into a wall charger . This is useful for clean installs in rooms where cables are not…
Minimalist enclosure for the Seeed Xiao ESP32C3 with the mmWave sensor. If you want to replicate the electronics just foloow the below links with the instructions. To secure the mmWave sensor to the enclosure i just used two M1.6x4…
The MMWave sensor in my Everything Presence One was a little ‘wobbly’. This is a very simple sleeve that slips over whichever header you are using and removes angular torque from the MMWave pins. The render shows the part mounted on the…
Case to house LD2410 and D1 Mini. Printed in PLA, no supports.
Enclosure made for the mmWave presence sensor featured in Everything Smart Home video: Components include: Wemos D1 Mini mmWave sensor Remixed from models created by jevis on Thingiverse: https://www.thingiverse.com/thing:5353636 Printed…
wall mount for MmWave Human Presence Motion Sensor. mount with 2 4mm screws and slide it in. link for the sensor: https://s.click.aliexpress.com/e/_DCTkUQX donations: paypal.me/IfrahOmri
https://apolloautomation.com/ The ball mount is a remix of: https://www.thingiverse.com/thing:67911 from Gyrobot
Case for the SeeedStudio XIAO ESP32 C3 and the 24Ghz mmwave Human Static presence sensor for XIAO (based on LD2410) Has room for the Antenna that comes with XIAO C3. Snap-fit lid. 0.2mm tolerance in the model. Sensor used:…
I have designed and printed these cases for personal use in PETG. It can be panned and tilted and has a cutout for the USB cable. Software in my case is ESPHome connected to Home Assistant
This is a remix of the presence sensor originally designed by @FSquare_1622667. I made a few tweaks to suit my needs: Replaced the original screws and inserts with plastic screws (I didn’t have the metal ones at home). Thinned the walls…
Case and stand for ESP32 mmWave and PIR Occupancy sensor suitable for a smart home. Based on this video here: Please note that I have not yet finished the lid to complete it however lots of people were asking for it as is so here it goes…
This is an enclosure to house the mmWave presence sensor that is used by the ESP8266 board. The mmWave sensor build was created following the Everything Smart Home Video channel. I recommend watching the video to understand how to build…
A small box created to fit a ESP32 C3 super mini + DFRobot mmWave Radar (SEN0395), in my case for use with ESPHome. It has a snap fit lid with slots to make it easier to get off again. I've added my parameterized Fusion360 file for easier…
My ESP32 board has 30 pins and measures about 29mm x 52mm. I had to remove the pins to make the whole assembly thin. I wasn't happy with how large the other enclosures that I could find were. I also didn't find many cases that fit the…
I've purchased a couple Sonoff SNZB-06P mmwave Zigbee sensors, but I didn't like that the size of the sensor was so large with the magnetic base. So I designed this back cover to make the device much smaller. It is possible to stick it…
It the simplest holder i could come up with. May add a ball-joint to the back, in case i want to mount in a differnt one, depends, how well it will function.
*Updated profile to v2 - improved design which is now easier to take apart (better gap tolerances, and an indent at the back to prise it apart without damage). Snug click-lock case to build an mmWave sensor for ESPHome using an ESP32-S3…
The MR60FDA2 and MR60BHA2 Sensor leverage 60GHz mmWave technology and offer reliable human presence & fall detection, and human presence, breathing and heartbeat detection respectively. Featuring light level sensing, an RGB LED for…
This is an adjustable coil for a mediumwave DIY detector-radio. For most of the most popular stations in Europe you'll need about 30 turns which gives an impedance of 50 - 180 uH. Frequency range is about between 550kHz and 1100kHz. If…
If you build a presence sensor with a Wemos Lolin D1 Mini and a mmWave Radar Sensor from DFRobot, this case is for you - my design is inspired by the borg cube :-) Follow this tutorial and the links in the video description by Everything…
---- new model without battery ----- In the free applications for home automation, you can create your own sensors to control/detect the environment. To create a detector/sensors, you need to have some electronics cards to create a new…
Read my article about this project: https://www.strangeplanet.fr/devlog/posts/2025/03/mmwave-presence-sensor/ The case is mounted on a orientable ball. To assemble the ball to the case body you will need a 20mm M3 screw and a threaded…
I designed a small enclosure for the HLK-LD2410B-P mmWave sensor bord for use in Home Assistant. More details can be found at https://github.com/jonnybergdahl/Sensor_LD2410B . I have included the Fusion 360 file so you can remix it as…
Case to make a presence sensor with an ESP32 NodeMCU32s and an LD2450 mmWave sensor, the lid also has holes to glue 9x3mm neodymium magnets. The ESP32 and LD2450 should not require any glue and should stay in place once the lid is screwed…
Designed this alternative wall mount for the LD2450, as I wanted to mount the sensor flush against the wall using tape. Remixed this remote wall mount for this use case (the design is a bit rough, so I attached the Fusion360 file if…
Old school detector radio technology meets 21st century 3d-printing. This is a simple to build and use detector radio for the mediumwave band. And yes - it runs without batteries (by only using the transmitted radio energy). We developed…
This is a custom presence detector I made that is meant to be similar to the Everything Presence One. The components are roughly $20 before shipping/tax. It has the following components in it: Seeed esp32c3 mmwave ld2410b sensor (I…
This is an external housing for the sensor to mount it to a wall with a command strip. Printed in PETG
This is a case to house the D1Mini and the Presence SEN0395 chip in a small form factor to be used around the house. It blends into any outlet when paired with the charger listed below. The instructions on how to make the board can be…
24GHz mmWave Sensor for XIAO - Human Static Presence is a expansion board for Seeed Studio XIAO series. It is an antenna-integrated, high-sensitivity mmwave radar sensor that is based on the FMCW principle. Combined with radar signal…
A vertical mount for a cheap tuya zigbee or wifi PIR (passive infrared)/mmWave motion presence sensor I found on AliExpress that is compatible with the IKEA SKADIS pegboard system. I printed it vertically with tree supports for the hooks.…
See description in the main model https://www.printables.com/model/1020388-esp32-d1-mini-ld2420-24ghz-mmwave-radar-sensor-esp Difference : ESP32 S2 mini used and the radar LD2410
Remix with added 2mm thickness to base layer.
Shelf mount point remix of the holder
This is a tilting enclosure for the Seeed Studio MMWave Lite radar module (https://wiki.seeedstudio.com/Radar_MR24HPC1/) with a base that can hold a microcontroller like an ESP8266 D1 Mini. Printing Notes: This is designed to be printed…
Angled mount for the Linptech mmWave ES1 sensor. Mounted with magnets to allow for easy sensor removal and attachment. Flat bottom on the other end, I have been using command strips to adhere it to walls. Sensor face is at a 50° angle…
Holder for LD2410 with Wemos D1 Mini for IKEA Skadis Boards. The Case can be turned to left and right by 50° Parts needed: LD2410B Wemos D1 Mini M3x35mm + M3 Nut or M3x30mm + M3 heat set insert 4x 3x12mm self-tapping screws Print Settings…
In the free applications for home automation, you can create your own sensors to control/detect the environment. To create a detector/sensors, you need to have some electronics cards to create a new device to add in your Home Assistant…
Designed to fit a custom PCB using just these 2 components. Gerber for the PCB is also attached. It is a very simple design but may be updated in the future to also include a BME280. Uses an ESP-32S Development Board and the LD2410C Human…
The C6 can use an internal antenna so the antenna holder was repurposed for attaching the mmWave sensor. The lid fits on the base a bit loose so I applied some superglue to the perimeter of the lid to attach it to the base. I used some 3M…
This is the case for an ESPHome based presense and environmental sensor. The code for ESPHome and the HomeAssistant cards is on GitHub https://github.com/withanhdammit/ESPHome-Presence . This project uses a 24GHz mmWave sensor ( LD2410C )…
A precision, two-piece, 100% support-free snap-fit enclosure engineered for a high-performance ESPHome / Home Assistant multi-sensor. It houses an ESP32-C3 SuperMini, an SHT41 temperature/humidity sensor, a VEML7700 ambient light (lux)…
Please refer to the original model for a description. I made this to scratch a particular itch, and thought it may be useful to someone.
Quick to print tripod mount for the Waveshare HMMD mmWave Sensor S3KM1110
mmWave motion sensor for Ikea Skadis
A vertical mount for a cheap tuya zigbee or wifi PIR (passive infrared)/mmWave motion presence sensor I found on AliExpress that is compatible with the IKEA SKADIS pegboard system. I printed it vertically with tree supports for the hooks.…
*Updated profile to v2 - improved design which is now easier to take apart (better gap tolerances, and an indent at the back to prise it apart without damage). Snug click-lock case to build an mmWave sensor for ESPHome using an ESP32-S3…
The Apollo Automation R PRO-1 PoE mmWave Multisensor (LD2450 and additional LD2412 add-on option) is our most advanced presence sensor. Designed for power, precision, and reliability, the R PRO-1 is a compact PoE mmWave sensor built for…
The C6 can use an internal antenna so the antenna holder was repurposed for attaching the mmWave sensor. The lid fits on the base a bit loose so I applied some superglue to the perimeter of the lid to attach it to the base. I used some 3M…
