Counting matching models…
This bracket supports your NooElec NESDR SMArt v5 & LaNA LNA when coupled with the SMA adapter that comes with the LNA. It protects the connectors from being strained. The LNA needs to be upside down so that its connector lines up with…
Case for the Nooelec LaNA HF - Ultra Low-Noise LF, MF & HF Amplifier. Base includes two holes for mounting, or optionally, put in some m3 heatset inserts to keep your board secure. The two halves slide together with a small lip that…
Just a simple case for the Nooelec Balun OneNine V2.0. The PCB fits over some small posts- these can be melted a little with a soldering iron if you want to secure the PCB in the case. However the lid does a pretty good job of this when…
Remix of @Gracro's Balun One Nine case to fit the V2.0b3 board revision. You may need to clip the leads on the back side of the board in order to get the lid to close properly.
In diese Halterung passen beide Geräte hinein. Am Antennenanschluss ist eine Zugentlastung für den Antennendraht angebracht.
Added attach points for the antenna wire to take the strain off of the connector. Category: Electronics
This is designed to hold a Nooelec Nano 3 SDR module together with an MCX to SMA adapter and a small 70cms antenna. The main reason for this is so I can use it with my Android phone and it makes sure the push-in MCX connector is held…
I had a spare HackRF One PCB from a Portapack, so I purchased a Nooelec aluminium case to put it in, but the case was slightly too short for my 3rd party HackRF One PCB. So I designed this 1mm shim, one required for each end. The notches…
I need an holder for my Nooelec Flamingo (FM filter) and LaNA (LNA) and I want to use Grifinty system from Zack Freedman! So I made it! Magnet are friction-fit, it could be too tight… If needed I could upload standard 6.5mm hole for…
If you ordered this kit "Extruded Aluminum Enclosure Kit for Ubertooth One” by NooElec https://nooelec.com/store/extruded-aluminum-enclosure-kit-for-ubertooth-one-and-yard-stick-one.html and it has a square antenna try this cover instead.…
A protective base for the NooElec Ham Filter Bank. You will need some small self taping srews, around M1.5, or a couple of drops of hot glue to secure the filter bank to this base. Easy to print in PLA, flat side down, 0.2mm layer height,…
This adapts the Nooelec GOES Satellite Dish to the DirecTV Slimline Back Assembly model number Bau4r2 The mounting hardware the Nooelec comes with is barebones at best (couple U bolts and a 90 degree metal bracket) which does not give the…
VESA-to-dish shim A printed block that bolts to a monitor arm's VESA quick-release plate on one face and takes the satellite dish's mounting plate on the other. dish plate (ears up, flat face down) │ M6 down into the shim…
A protective base for the NooElec Ham Filter Bank. You will need some small self taping srews, around M1.5, or a couple of drops of hot glue to secure the filter bank to this base. Easy to print in PLA, flat side down, 0.2mm layer height,…
This adapts the Nooelec GOES Satellite Dish to the DirecTV Slimline Back Assembly model number Bau4r2 The mounting hardware the Nooelec comes with is barebones at best (couple U bolts and a 90 degree metal bracket) which does not give the…
These brackets were made for the Nooelec NESDR Smart v5. The dongle is held via friction fit and has plenty of clearance for USB extension and SMA cables to attach. Includes openings on the sides of the dongles for air flow (I have a…
