Counting matching models…
I recently built a new PC and was impressed by the aesthetics and performance of the Lian-Li Lancool 207 case. However, I found a design flaw at the rear of the case. The large hexagonal mesh has two issues: The bottom fans can suck in…
I couldn’t come up with a decent solution to mount it to the frame, but maybe someone else can.
This modification was born from the need for better motherboard cooling due to the swap to 0.9deg Stepper Motors. Using these motors at a high acceleration causes the stepper drivers on the motherboard to overheat and shutdown momentarily…
This is a remixed version of the awesome model by Keenan with a few optimizations and some extra parts/accessories. Enhancements I had a hard time hammering all the parts together, in fact most of the inserts didn't fit at all when…
Hello everyone! I designed these 3D-printed supports for 30 mm diameter springs, intended to isolate the seat, enhance the performance of the bass shakers, and minimize vibration transfer to the rest of the simulator. The 3D support…
Bei der Topologieoptimierung geht es darum, die Materialmasse eines Bauteils zu optimieren, um dessen Gewicht (und damit dessen Kosten) bei gleicher Steifigkeit zu verringern .
Modular and Iterative Design Focused Muffler / Silencer for Air Compressor Intakes: This is my design of a muffler for my air compressor which uses ½" threaded muffler components. In tackling this project, I reviewed several other…
this is a collection of little helpers for Oregon Minitrack holder to place a compass on it to place it in North longer holder for polscope to see Polaris also with mounted camera holder to justage the polscope
Meine Hand ist größer als der durchschnitt und die Maus hat nicht gut in meine Hand gelegen. Da ich an meiner Hand nicht ändern kann musste die Maus angepast werden. Die Maus ist im ganzen länger und hinten unter der Hanfläche an den…
Neue Version mit Daumenauflage!!! Meine Hand ist größer als der durchschnitt und die Maus hat nicht gut in meine Hand gelegen. Da ich an meiner Hand nicht ändern kann musste die Maus angepast werden. Die Maus ist im ganzen länger und…
Preface: Since the beginning my XL was troubled with many problems that also included severe VFA's (you could even feel the ripples), unequal belt tension or misaligned x-carriage and unable to calibrate IS as either one or the other belt…
The optimization has been carried out considering only one load case, which is depicted in the following image. The optimization process is solved employing a topological-derivative-level-set-based topology optimization algorithm.
Morserino M32 Pocket prototype case (differs from the QRP Labs production version)
RC Mini Forklift (Remix) Beginner-friendly remix featuring 7 modified parts for an easier build. Features: Front-wheel
preferably as many perimeters until no more infill is needed in the curve area. the small one is for a belt width of 25mm and a bolt diameter of 5mm. 2 pieces 3x16mm countersunk screws are required. the belt guide is optional. The big one…
I got the Viswhoop, as the price for the complete copter was only a bit more expensive than the Caddx Vista itself. As expected for this price point, the frame and the hardware is somewhere between mediocre and "okayish". With this kit…
This is a simple remix of the great fan mod for the Creality CR-10S by Gabriel3DCaster to adapt it to the Alfawise U20-ONE. I have adapted only the Fan_Mod_New_Version model. Since U20-ONE is basically a clone of the CR-10S the original…
I've made these parts to optimize the controller handling for especially games like Tetris or Doctor Mario. You can either print the whole 4-way button or use the shims to tune your controller as you like. Recommendation for the 4-qay…
Bridge - Topology Optimization The file that has been printed out is "Manual reconstruction.stl’" Category: Buildings & Structures
Bridge - Topology Optimization. The file that has been printed out is "Manual reconstruction.stl’" Category: Buildings & Structures
"BEAM" - TOPOLOGY OPTIMIZATION Volume reduction: 60 percent How I Designed This Abaqus Category: Engineering
I have topology optimized a cube of 100x100x100mm. Fracture occurred at 23544 N Category: Engineering
