Counting matching models…
Uses 4 magnets for if you wanted a more permanent fixture you could also use a bit of superglue along the lip and groove, for adhesion id recommend superglue, adhesive strips or double sided sticky tape 3X1mm magnets…
An organiser holding 2 TZ (TZe) Brother label maker tapes I use it to keep yellow (warning) and red (danger) tapes at hand Print notes No supports needed Updates log 2024-10-12 Initial version released Support the author The model is free…
multi use inlays for milwaukee slim packout: drill holder 1/4" bit holder low + high SDS-drill holder jigsaw blades
Designed to take the slightly thicker tokens that some copies of the game have. This means that the 6 token columns are taller, and so are the spare token slots underneath the share tokens. May fit less well in some boxes, due to height.
PLEASE - if you like this model, give it a like? Thank you! This Gridfinity drill bit storage tray is 4 x 5 standard (42mm) grid units, and 3 standard units height. It stores 18 different drill bit sizes. I made it for HSS 1.0 to 10.0 mm…
I needed a desk organiser to tidy up my lithium battery chargers and cables. Quick and easy to make with the Maker World MakerLab tool.
Update April-26: Thanks to @WK_0bjkt_4142451 for highlighting that some of the newer boxes have additional tabs that prevent these holders from working. Please see his comments for details. v2 update : Improvements to have a tighter fit…
Slay the Spire: Board Game Inserts to speed up setup and storage for the bottom part of the Deluxe box. This was tested for the Deluxe box, but some parts can be printed to be made use in the normal box as well. Supports double sleeved…
Dies sind Halter für die More Zerup Sirup Flaschen. Für 2, 3, 4 oder 5 Flaschen. So kann ich ungenutzte Flächen im Schrank nutzen, und die Flaschen sind Aufgeräumt. Diese können ohne zu Schrauben in die innen Seite einer Schranktür, oder…
Didn't want to fiddle with the tiny tokens that came up with the Gundam Card Game starter boxes, and have made a little organiser for 16mm or 15mm (Gundam sized dice) dice and my own tokens. The box is sized to match the dimensions of a…
Easily slots into the single Wentai boxes. Just tear open your SMD strips right over it and watch the 0805 resistors go straight in the box and not fly all over the place.
2x4 Gridfinity storage for 4 passports, insurance cards and travel money. Angled to enable storage within an IKEA Alex short drawer.
It's a drawer replacement. No front pieces other than a simple handle.
Building on my previous model and improving in some key areas, I have created this organiser for the Scourge of Ghyran! This handy organiser contains everything from the general's handbook. This includes: A primary compartment, which…
This organiser was designed to maximize drawer space and be as large as possible while fitting on a 256x256 print bed. All the components can be printed simultaneusly on a single bed without supports.
Not much to say about this really other than it was made to store my valve shims for my motorcycle. Category: Tool Holders & Boxes
UPDATE 27 Jan 2026: Added a scaled up 23ml variant. A simple 4x2 paint organiser. Use it as an insert for drawers, boxes etc or simply lay it on your workbench/table. Fits Tamiya, Mr Hobby, Mr Color paints well. Test printed in Black PLA…
About as simple as you can get as far as desk trays and organisers go. Use them to store your wireless earbuds, jewelry, watch, wallet, etc. Can print out of any material, although due to them not bearing any sort of load, cosmetic…
Tired of the deep, cluttered "black hole" that is the Jimny glove box? This custom-designed organizer transforms that space into a functional storage system, making it easy to find your registration, sunglasses, charging cables, and…
Do I know how to 3d print? Not really. Will this work? Hopefully. Basically to use the product, you first slide in rubber bands in the small slots, on both sides. Then when inserting or moving cables, you slightly pull on the rubber band.…
Weekly Pill Organiser 7 Days, 4 per Day. When you need more space for your Pills, this is the Bigger Pill Organizer. 14 Pieces Magnets Diameter 6mm x 2mm used . Link to OnShape (German Version)…
The OEM cup holder organiser from Skoda had 2 faults - the phone slot was too tight for my phone (S23 Ultra with a cover on), and it blocked part of the remaining cup holder, essentially rendering both centre cup holders unusable. I tried…
A functionally designed Oral-B organiser , precisely manufactured on a Bambulab 3D printer. The organiser offers: Space for an inductively rechargeable electric toothbrush (suitable for classic Oral-B charging bases with a round contact…
Made this to store playing cards from various games. 1st version is made to fit standard playing cards - cca 90 x 64 mm 2nd version (visible on photos) is made to fit cards with card sleeves - 94 x 67 mm
My setup was top heavy so i made a 'leg' for the '2' high variant, and i shoved it under the adjacent basket
A simple bathroom organiser, to help me, organise my shavers ant their accessories. Dimensions (WxLxH): 96x170x50 mm Settings: Supports: No Resolution: 0.2mm Infill: 15% PLA, PETG Filament brand: any Filament color: any
A box to keep your knitting needles organised. It fits needles with a length up to 220mm. If you have needles shorter than 160mm than you should scale the z axis of the base a little bit to be able to grab them comfortable. Printed with…
I refined the model from MacsonCAD to a more accurate fit, with a draft angle to match the angled sides of the box.
This is the free version of my cable organiser. The full version is on Cults 3D. Category: 3D Printing
Made this version 1 of the TTRPG minifig organiser, to make it easy to store and move more minifigs for TTRPG games like DnD Made to fit one inch bases. Thiis is a project in development. Design is to minimize filament usage. after the…
Draw separators for 65mm plastic draws from this item I purchased this set of drawers from Aldi but I believe them to be the same set. Unsure if they will fit other 65mm drawers you will have to let me know :) in the images the Blue…
HeroQuest Tabletop Organiser All parts are measured to fit the 2022 Avalon Hill reprint of HeroQuest. This modular set is designed to keep your character sheet, pencil, and cards tidy and accessible during gameplay. The main board acts…
Exactly as the title says. 7 high currently avaliable, more to come later
A Remix based on the Design from Robbycor (@robbycor_1107199)
It’s empty! Now what? Your eSun cardboard spool is empty? ♻ Turn it into a compact storage station for your 3D printer! This design consists of a top and bottom cover plus compartments for tools and spare parts. All parts except the top…
I pulled all models onto one plate for printing as well as adding text cut out to make it easier to remember which parts go where when packing away
About These 2, 3, and 4 compartment dividers sit inside the drawers of a commercially available organiser. The organiser I purchased from Amazon UK is called "simpa 60 Multi Drawers Plastic DIY Tool Bit Storage Organiser Cabinet", but the…
Carcassone kids tabletop game inserts. There are 2 different inserts provided: carcassone-kids-insert - space for stack of game cards and figures/meeple, carcassone-kids-figure-insert - 4 separate compartments for figures/meeple to for…
Risk Army Organizer / Storage Upgrade your Risk board game experience by ditching the flimsy cardboard inserts for these durable, 3D-printed army organizers. Designed to be a drop-in replacement for the original storage boxes in the…
A desktop organizer with a fine 3dprintable mesh so you can see what is in side.
This is an Electronics organizer with multiple drawers of various sizes, trays, vertical slot, file holder & pen holder.
This model is inspired by in-game warning systems( rabbits) , it can be used not only for sotring your one blade but also somee other things in your bathroom. It also has a little water drain on the side so the watter dont stay in the…
Modular Hacker Desk Organizer – Flipper Dock Edition Designed for hackers, makers, and electronics tinkerers, this all-in-one bench organizer gives your daily tools a proper home. Built around a precision-modeled Flipper Zero profile,…
A small organizer designed in the form of a car cylinder block. This organizer will appeal to car enthusiasts. It's a great gift for men. Органайзер в виде блока цилиндров восьмиклапанного двигателя ВАЗ
This extension cord coil organizer features a two-piece spool design with a threaded central hub that allows both halves to screw together into a compact cable carrier. The spool has an outer diameter of 240 mm, while the center section…
10" by 9" Modular drawer organizer. To use: Place the dividers in the slot to make sections of varying sizes
Minimal porta usb e penna da disegno. Progettato per affiancarsi al tablet ha alloggiamenti per 2 chiavette usb e 2 u
This is a 1/2" socket holder designed specifically for the Parkside Organiser & Storage Set wall system. It allows you to neatly store and organize your sockets while keeping them easily accessible in your workshop. The holder mounts…
this is the most compact easy to make a lot of and cheapest way to store parts i've seen. couldnt find one so made it. It can store a lot of bags of diffrend sizes and they dont fall because of the little sawtooth texture in the buttom of…
Push dyspenser for a pills. Simple model, very usefull. It contains only 4 parts, but only if you count 2 springs as separated parts. To assemble, place two springs in the recesses and insert the button. It should hold tightly, but I used…
With this storage tray you can keep all your rolling supplies stored at the ready in one place. Store unopened filters and papers at the back and loose at the front ready to use, The holder is tall enough to store 3 unopened packs of…
1/4" 3/8" 1/2" 2 Sizes for each for larger and smaller sockets, can add as many or as few as you like in a line, they slot together loosely. They are compatible across the sizes so you can continue the line with any size socket. Made for…
Of course! Here’s the English version: "I am a freelance designer who creates custom solutions for my own needs. I design and share everything I need, and if you have an idea for something you’d like designed, please let me know—I will…
Organises threaded heat insert tips by the different sizes with the text description next to them. Uses 6 M4x6mm heat inserts. NB: This is based on my heat insert tool and how it fits to my iron (it's one of the cheap kits from…
Modular tea organiser - can be divided in up to 6 parts. I have made two widths which should be suitable for most of the tea bags. Printed with PLA.
My wife wasn't happy with the selection of cross stitch thread organisers on here so I made her this. 34 rings. The slot in the middle accommodates a slip of paper or card, dimensions 20x235mm. 237mm x 57mm overall.
This is basic organiser for 3D printer tools. Size 90x90mm I made it so it contains caliper slot, 2x USB, 2x for pen, twizers or similar, glue, and small tray for screws or something like that. Print settings: PEI plate Heatbed…
This is my first 3d design. Perfectly fits our Nordhagg in our bathroom.
The organiser holds the cards and the pens for the "Next Station" game series. I tested it with Paris and Tokyo, I hope it fits the London box as well. The pictures are of version 1, where the opening on the side of the pens is too big.…
Organiser for Roborock S7 accessories Place for: 6x Filters >10x Mops >10x Sidebrush and some space for other stuff Lid coming soon...
Desk organiser which can hold pens pencils boooks etc it has a book holder and then it has a big storage system where theres 2 columns ones empty and one has 2 long columns which when u pull out it has 2 more drawers with gud design handles
A minimalist organiser tray which holds the following Wera 8790 HMA Sockets: 5 5.5 6 7 8 10 11 12 13 I printed mine in ASA.
A minimalist organiser tray which holds the following Wera 8790 HMB Sockets: 8 10 12 13 15 16 17 18 19 I printed mine in ASA.
I own several of the smaller Wera Joker combination wrenches (bought them all separately) but I had nowhere to store them properly. This is my solution. It holds the first six wrenches in the 6003 series. This includes: 5.5 6 7 8 9 10 I…
This holder/organiser holds 8 Wera micro screwdrivers (118 series). The drivers oppose one another for a nice balance between space efficiency and presentation/ease of selection. There is also an alternative version with enlarged holes on…
Storage inserts for the Alien RPG Evolved Starter box to support; Booklets, Maps, Manuals GM screen Cards, Tokens, 40 dice. Modified version of the Alien RPG Organiser created by RPGranger + additional assets from Korharan and Pavel. Snug…
Idealno za vijke M3 x 1-20 mm. (nisam je probao al' mislim da može vrlo dobro radit' i za vijke M2 x 1-20 mm)
Handy chopstick organiser so they never get lost in your drawer. Can hold up to 10 chopsticks, but can easily be modified for more or fewer chopsticks.
Organiser fits perfectly into the plastic box supplied with various Palintest Lumiso photometers to help keep you tablets organised. A much better solution than the piece of cardboard they supplied!
I wanted to organise the wiring into my dual UHPs and Omron SSR. I wanted to use wagos and I also wanted a protective cover once it was wired in to keep it extra safe BOM: 2 x Voron spec heat inserts (M3x5wx4L) 2 x M3 screws (sorry will…
Contact lens holder designed for Alcon Dailies Total One lenses. There is an opening at the bottom so that you can pull out and use up the oldest lenses first while loading new batches into the top. It probably works with other lenses…
I designed this organiser for my girlfriend's Skadis board for pencils, brushes, scissors, etc. It has two “pockets” with dividers. printing preferences on BBL P1P: printed with Redline PLA 0,2 mm standard quality 20% infill brim auto…
Overview: This system utilizes standard, affordable ID cards or RFID cards and works seamlessly with any dry-erase marker. For optimal use, fine tip markers equipped with an eraser are recommended. System Features: 1. Card Storage :…
EDIT: uploaded v2 - lower height to 9 mm (enough) and adaptors with longer distance so you can put Thule back raiser in-between. We just bought Thule Urban Glide 2 stroller and actually the stroller needed some upgrades. Already found…
Both versions fit perfectly next to each other in our cutlery tray and hold a lot more cutlery than flat holders thanks to the slanted design. Beide Versionen passen perfekt nebeneinander in unseren Besteckkasten und fassen durch die…
Depending on accuracy of print , feet may require clearancing with rotary tool or engraver to fit over studs.
Food cans are ready to repurpose for many different situations, including tool holders or desk organisers. However there's an annoying tendency for small or long tools, to fall sideways or get tangled with other tools. Sort it out with…
nice for people who like sewing. there is two types of boxs ‘normal box and lid’ and '' deep box and lid.
I'm embarrassed to publish this remix, because it really is a “hack." But maybe it will help someone. I needed a cable organizer for an earphone that I use while backpacking. The wire/cable for my earphone is very thin. So thin that it…
I designed this as I am always using my verniers at work and home, but never get round to putting them back into their cases to keep them protected. They just end up left on my desks where on day someone is bound to knock them off. This…
A box for stickers is hidden in the organizer and can be conveniently removed if necessary, which saves a lot of space (maximum size of stickers is 76x76mm), and this box can also be used as a phone stand the right side of the organizer…
Organizer for round and rectangular signs. round sign d:200mm rectang. sign 150x150mm
