Counting matching models…
I loved puhlbo's PCP Airgun Moderator / Suppressor but wanted to be able to print with less material and in less time. This answers that. Seems to work very well on a 6 FT LB air arms S200. I don't have a db tester, but it definitely…
One piece printable PCP Rifle Silencer. Designed for ½ 20 UNF thread (compatible with many air rifles). Fully functional and suppresses most of the sound. Lightweight and durable. PETG, infill 100% 0.20 layer height,
Back nut that is suitable for Foster and PCP bulkhead connectors. Specification: 1/8 NPT thread 3/8" diameter thread 6.4mm nut height 15.8mm nut outer diameter Print high infill, no supports required 0.1 layer height, but works on 0.2…
Replacement for the magazine key from Hatsan
magazin besteht aus drei teilen rückwand kann mit sekunden kleber geklebt werden
A imprimer en 0.2 avec supports Nécessite 2 vis M3x25 et deux boulons M3
PCP fill adapter cover. Similar to: https://www.thingiverse.com/thing:4840077 although this unit is completely customizable. Category: Sport & Outdoors
The holder is for the PcPanel Mini . It is attached with 2 screws and the PcPanel Mini is simply pushed in.
PLA, 0.2mm layer height ,20% infill
This is a fill port cover for the edgun leshiy fill port. It may fit other fill ports. It's designed to slip fit over the 14mm nut for the BSP fitting and protect the fill probe from dust and dirt. There are two lanyard holes for…
Only extruded frame Profile
I printed this in PLA+ supports are needed for main body the tpu pad fits into the cap with a bit of pressing on the tabs from the sides to get them in the slots and is pretty snug the cap is then just a press fit, locks in place, to the…
Hey! Ich habe ein Gehäuse für den RetroScart Switcher von PCP Retrotech entworfen, da ich es nicht mochte, dass die Platine ungeschützt war und sich beim Einsetzen der Scart-Kabel leicht verbiegen ließ. Um dieses Problem zu lösen, habe…
For those who are more interested in accuracy than rate of fire, this is a single shot load tray for theBenjamin Marauder. Its generally considered that single shot tray give a much better, repeatable accuracy due to the fact that the…
These parts assemble with a minimum of hardware. You'll need three (longish) zip ties, one 3mm X 20mm screw with nut, and 1 2.5" ¼-20 hex head bolt and thin nut. Remove the cover from the compressor and drill a single ¼" clearance hole…
PCP 30mm adapter for Bipod picatinny Yellow insert printed using TPU filament Bipod you can find here: https://www.printables.com/pl/model/357606-bipod-for-picatiny-retractable
Fits Hatsan TactAir PCP Inline Universal Air Filter for Portable PCP Compressors. I really love these little compressors but you absolutely need to use an additional filter inline, as so much moisture is present. Just print it, and fill…
The mount is compatible with the PCPanel Pro model. This design has optional foot holes on the bottom of the device. You can unscrew the rubber feet from your PCPanel Pro and attach them to the stand for extra grip. We are not liable for…
This is a storage tray that fits the gridfinity system to organize your tools. All the spare parts for both the large and small primer bar pins etc (everything that comes in the box) have a home in this tray. This is designed to clear the…
Es gibt zwei Möglichkeiten, aus zwei Teilen oder einer ganzen Vergangenheit bei Diana Bandit und Diana Chaser
Krytka pro ventil ruční PCP pumpy ke vzduchovkám, aby nepadal prach dovnitř.
This is a friction fit cap that goes on the quick connect of the outlet hose of a PCP Compressor to keep out dust and debris. I lost the original insert on the first day I had the compressor and wanted something I couldn't lose. It was…
Designed for this molecular Sieve but can work on any that have a diameter of about 50mm. Standing the sieve up is important for saftey as it reduces the amount of moisture and water that can end up in your tank. The model this is remixed…
51 mm Durchmesser für einen 16-mm-Ballon. Und 61mm Durchmesse Flasch mit Abstand zwischen Lauf und Flasche 13mm Три разные восьмёрки две на ствол 12мм а одна на 14мм ствол Ствол 12мм - расстояние между ствола и балона 13мм- диаметр балона…
Zip tie attached hose adapter for the FX 4 Stage PCP Air Pump or the identical Gehmann M100 4-Kolben compressed air pump. The hose holder can also be mounted without a cable tie, but then it might slip. The adapter should fit all pumps…
to be continued lots of information inside :) Print Settings Rafts: No Supports: No Resolution: 200 Infill: 20 Filament: PolyMaker PLA Category: 3D Printer Extruders
Benjamin Marauder degassing tool. Vertical printing, better threads and good compression resistance with PLA+ (proved). Removes air or CO2 from the Marauder's reservoir. Replace the CR-PCPDT2 part Note: This degassing tool works very well…
Story I really liked the legs u/Michenzo23 designed ( full credit ) but I wanted to modify it for two reasons: 1. Set my own leg height (to get a larger angle) 2. Mount the original feet on the bottom to keep it from sliding on my desk.…
Attention! Requires a 3D-printer with height of a printing area 25+ cm Non-printing parts: 2 pieces of foam D = 2 cm * H = 1 cm are required in each half of the case. Внимание! Требуется 3D-принтер с высотой печати не менее 25 см.…
Print in PETG , 4 perimeters/walls, 0.2mm The link below is the oil/water separator /filter in the pictures above but it should work for many more on Amazon and Aliexpress with a diameter of about 30mm.…
Hi there :) So this is the second version of my idea for a combined stand/mount for a PcPanel Pro + Stream deck XL. After using the previous design for a few days I found it way too chunky and took more space on the desk than I would have…
A nicely fitting dust cap to protect the PCP fill probe / fill adaptor for an air gun / air rifle. My fill probe from AirMaks has a foster coupling, but likely it will fit other models as well. The inside diameter is slightly tapered so…
A simple stand for the PC Panel Pro to sit at the same angle as a Stream Deck XL. For assembly you will need 4, m3 10mm screws.
The idea behind this design was that I wanted to have My PC panel pro & Elgato Stream deck Xl as close as possible sitting at the same angle and be connected to a built-in USB hub so that only one cable would be going across my desk to…
soporte reforzado para colocar la manguera del inflador pcp, super reforzado y muy funcuional
The mount is compatible with the PCPanel Mini model. This design has optional foot holes on the bottom of the device. You can unscrew the rubber feet from your PCPanel Mini and attach them to the stand for extra grip. If you want to sell…
Recommendations for printing: material: PETG layer thickness: 0.2 mm Non-printing parts: Steel optical axis (D=3 mm, L=100mm, it can be removed from old CD drive, etc.) Self-tapping screws with hidden flat head M3 * 8 mm x 2 pcs…
Done with the clamshell for the spa master, now I will work on a foldable or fixed stock. for the clamshell to fit you need to cut of the front "iron sight". I will add a replacement picatinny rail instead of the back iron sight that can…
Back rider for PCP airgun (jezdec pro pcp vzduchovku.)
Simpler, aber perfekt sitzender Picatinny-Schienen-Adapter für z.B. ein Zweibein um den PCP-Lufttank
Support stand designed for the GX PCP air compressor filter/oil-water separator. The original magnetic mount was not strong enough to securely support the filter on its own, which led to movement, vibration, and stress on the fittings.…
If you hate to leave your hose on the ground after filling your pcp gun, this is for you. Designed around the hill mk4 pcp pump that have a 24mm top cap with 20mm spanner may need to print it scaled down a bit for better fit
The Positional Cooling Platform Device (PCPD, known as the ‘CryoKit’) is a 3-D printable device that supports reproducible cryopreservation with standard cooling rates (5 to 35°C/min). The CryoKit accommodates French straws (0.25 and…
Patka pažby PCP vzduchovky
In mobile use of the Gehmann M100 or the identical FX 4 Stage Air Pump, the bulky and heavy original stand is a nuisance. That's why I made a folding stand. Two simple M8x55 screws or printed bolts (56x8, glue if necessary) can be used to…
Für lang und kurz pcp luftgewehre
just a peg board holding tool for the PCPS next gen precision primer seating system by Derraco Engineering. prints just fine without any supports at least when printing with the pegs for the peg board are printed separately. As you can…
A figure-eight bracket supporting the barrel and cartridge for the Gladius PCP air rifle.
Single-charge tray for PCP Strelka (5.5) with magnet 8mm Однозарядный лоток для PCP винтовки стрелка калибра 5,5 мм. Магнит на 8 мм. приклеивать суперклеем. PLA, заполнение 15%, стенки- 3 периметра
I made this to combat the $12 blinders that i was forced to buy every time i lost mine. This should last you just as long as the other non 3d printed blinders.
Для любителей точной стрельбы, предлагаю "cерьгу" для взвода на PCP винтовку Егерь/Jager. Многим моим клиентам кто приносит на обслуживание винтовку, предлагаю сделать за копейки "cерьгу" для взвода. Для изготовления вам понадобиться…
The Positional Cooling Platform Device (PCPD, known as the ‘CryoKit’) is a 3-D printable device that supports reproducible cryopreservation with standardizable temperatures and cooling curves. The CryoKit accommodates French straws (0.25…
Um meinen Neuzugang eine 4L 200bar PCP MSA Pressluftflasche an der Wand zu befestigen habe ich diesen einfach Halter erstellt. Meine 6,4L 300bar Flasche von MSA hab ich genauso an der Wand befestigt. Der innere Durchmesser beträgt 12cm.…
So I had my PCpanel pro for some time and did not enjoy using it when it was lying flat on my desk. I wanted it tilted upwards similar to my stream deck. After some time searching through the web, I didn't find any stand that I was that…
A moisture filter designed for the four uncles PCP hand pump and maybe some other chinese ones that have the same top dimensions Each time you pump without using any moisture filter a very small amount of water gets into the air reservoir…
Da ich meinen Öl-Wasser-Abscheider für meinen 300bar Kompressor selber mit Molekül Kugeln und Aktivkohle befülle habe ich dieses zwei Adapter gestaltet. Die großen Wattepads am Ein- und Ausgang sowie die Filze am Ein- und Ausgang können…
Need install M3x5x4 insert and M3x8 bolt
Simple enclosure for the PowerCab PCP Panel that is open on the back end to connect power cables. I used hot glue on each corner to affix the PCP Panel to this enclosure.
I made this for my Pinty Buster to hold the fill probe.
Print as it is in .3mf file if any problems feel free to contact me :)
Ein Bodenfuß mit einem Durchmesser 100mm, der Innenteil ist Kugelförmig ausgehölt, hierduch zentriert sich die Pressluftflasche von selbst. Auf der Unterseite können optional Antirutsch Filz oder Kunststoff Aufkleber angebracht werden.
A nice tool to have when soldering - or probing - printed circuit boards! Required hardware a neodymium magnet of 3mm x 12mm diameter M4x35mm bold M4 nut (with nylon) Spring of internal diameter > 4mm and outer diameter ≤ 7mm with length…
51 mm Durchmesser für einen 16-mm-Ballon. Und 61mm Durchmesse Flasch mit Abstand zwischen Lauf und Flasche 13mm Три разные восьмёрки две на ствол 12мм а одна на 14мм ствол Ствол 12мм - расстояние между ствола и балона 13мм- диаметр балона…
Simple enclosure for the PowerCab PCP Panel that is open on the back end to connect power cables. I used hot glue on each corner to affix the PCP Panel to this enclosure.
Replacement for the Benjamin Marauder 2F: SET SCREW 8-32x125, BRASS in the valve assembly when the thread of the original breaks (too many settings). Keeps the adjustment screw in place and is easily removed for further adjustments.…
