P
Printablessamh
Matek ASPD-4525 Pitot Tube
Reference CAD files for Fusion 360 for design of mounts, etc. Measured from part Fusion 360 f3d file included
- Downloads
- 376
- Likes
- 7
- Rating
- 0
Search results: pitot
Counting matching models…
P
Printablespeter.skotte
FrSky Pitot tube Side mount
Simple 2 part enclosure/mount for FrSky pitot tube. The two bottom holes are for bras insert with M3 thread to mount to aircraft surface. Category: Hobby
- Downloads
- 259
- Likes
- 11
- Rating
- 0
P
PrintablesThomas
Pitot Tube Cover
This is a simple cover for pitot tubes that are used for airspeed sensors on the pixhawk or other systems. It has a small hole for running an elastic or rubber strap to keep the cover from falling off before flight. Category: R/C Vehicles
- Downloads
- 198
- Likes
- 8
- Rating
- 0
P
PrintablesJS_SunnyFlorida
Dynon Pitot Tube Protective Cap
This is a 4-inch-long safety cap for a Dynon Avionics heated AOA Pitot tube. The cap has a key ring tab for attaching a "Remove Before Flight" streamer. This is a tight fitting cap; it may require some sanding on the interior to fit…
- Downloads
- 136
- Likes
- 11
- Rating
- 0
P
PrintablesDavid Cook
Pixhawk Pitot Tube Cover - REMOVE BEFORE FLIGHT by Beastmode Development
a 3D printed TPU Pitot tube mount for a REMOVE BEFORE FLIGHT tag. I made this for my RC VTOL using Arduplane 4.3 Enjoy !, Dave
- Downloads
- 56
- Likes
- 4
- Rating
- 0
P
PrintablesUenbzsto
Vase Mode R/C Pitot Air Scoop
A duct inlet/air scoop for cooling air on an R/C airplane or R/C car. Designed to be vase mode printed for a clean single layer lightweight part. As designed a single print will yield two copies of the inlet. Can be scaled uniformly or by…
- Downloads
- 38
- Likes
- 6
- Rating
- 0
P
Printablesᴄᴉᴚᴋᴉᴉᴛ
Velocomp PowerPod: Pitot Tube
As far as I can see, Velocomp only offer one pitot tube as a spare part, so this should fit all versions (don't hold me to that, though!) Print vertically, threads at the bottom with no supports required. Use quality setting 0.1mm layer…
- Downloads
- 33
- Likes
- 1
- Rating
- 0
P
PrintablesProkop
P28R Automated Gear Extension Pitot Cover
Pitot cover for autoamted Gear extension Piper 28 R - Arrow II
- Downloads
- 32
- Likes
- 2
- Rating
- 0
P
PrintablesSartor
Pitot tube mount for RC planes
Cut excess wires from back side of pcb to save vertical space Cut stainless pipes, leaving approximately 5mm for both tubes Print both sides with supports Sand plane slightly for better connection Assemble like on photo Apply small amount…
- Downloads
- 26
- Likes
- 0
- Rating
- 0
P
Printablesfred
Aquila Pitot Cover
In order for this cover to function as intended, it has to be printed with a flexible filament. When printed, just put it on the pitot-tube and secure it with the hook .
- Downloads
- 20
- Likes
- 0
- Rating
- 0
P
PrintablesWiktor Wrona
Pitot 4525 I2C wing mount
I don't have a link to the Pitot tube I used; it's an old, secondhand model. Mounting the PCB Holder: - Cut out the space for mounting the Pitot electronics box using the template - Cut a slot in the wing to route the Pitot tube wire to…
- Downloads
- 5
- Likes
- 1
- Rating
- 0
P
PrintablesCzechMate
Static port housing for RC pitot-static probes/sensors
This idea came from a housing KWBOOST (Kelvin) showed on his you tube feed to get stable barometric pressure for his flight controller, so credit goes to him. If you are not able to use the static ports on your pitot tube, such as the…
- Downloads
- 4
- Likes
- 0
- Rating
- 0
P
PrintablesAliaksei Basalai
ZOHD Dart 250g Pitot Tube ASPD-4525 Halterung
Zur Befestigung am Deckel werden M2-Gewindeeinsätze und M2-Schrauben benötigt
- Downloads
- 1
- Likes
- 0
- Rating
- 0
P
Printables
Pitot Tube tripod mount for measuring air pressure
This sucker has magnets, heatset inserts for tripod mounting and uses (m6? m8?) screws to secure the pitot device in place. I used this pitot tube these magnets this heatset insert