Counting matching models…
Folding dice tower with dice box to hold one set of standard sized polyhedral dice. No supports needed. Slight trimming of Tray required on the flat circles near hinge. 8mm Screws are the hinge for lid and tower Nuts, M3 | [QTY 15] Bolts,…
This was just a random idea for me to design and is a way to keep my skills fresh and improve upon them over the summer. edit: I added a new stand to address problems Note that it was a rush job as this was my 1st day of collage :p
Printed in PLA with .15 layer height and .4mm mozzle on a Voron Trident 350mm. Filament used is iiidmax Fluorescent Green PLA+. This adds a little bit of marble mixing when adding marbles back into the hopper. For a future design update I…
Just a simple disc with the treble cleft. Pause the print to change filament colors. I can model up a CNC router plinko board if there is enough interest.
Plinkodrop - Tabletop Marble Run A simple, mechanical tabletop plinko game designed for your desk. Drop the marble at the top and watch it bounce through a grid of triangular pins, funnel through the side ramps, split around a center…
After using my old dice tower for over 2 years, I had some ideas for improvement. This new one features a print-in-place hinge design Low walls on the tray ensure that your dice are easily readable after a roll During play, use the…
All you need are: friends, fridge and a lot of beer!! (also a 3d printer) All the parts mount 5x3mm magnets. for the pin you need 3 magnets for the esge you need 2 magnets for the finish element 1 magnet for the trasparent panel I used an…
Help make a decision just number your choices 1-5 and let the plinko decide.
This model is built as a functional desktop game rather than just a decorative board. The peg spacing, puck size, scoring area, side guides, stand, and drop lanes are designed together so the finished print can actually be played. The…
I made this for mini dice 15mm. It still uses M3 screws and nuts. It does need an 84mm x 100mm x 2mm plexiglass sheet for the front. I've also removed the dice holder section because I have dice holders and didn't need that part. I made…
A table-top drop game: lean the board back on its two legs, drop a marble in at the top and watch it bounce down through the pegs into one of the scoring slots. Take three drops each and add up your score. Great for parties, school fairs…
Plinko Tube Dice Tower This is a dice tower inspired by Plinko mechanics. It's designed to provide fair, random rolls while being easy to print on most 3D printers—no supports required. Dice dropped into the funnel bounce off internal…
I made this for mini dice 15mm. It still uses M3 screws and nuts. It does need an 84mm x 100mm x 2mm plexiglass sheet for the front. I've also removed the dice holder section because I have dice holders and didn't need that part. I made…
A plinko style dice tower designed for d&d. It's open faced so you can see the action, but the dice won't fall out of the angled pegs. See how it works here: https://www.youtube.com/watch?v=sI64v1gKJUo During play it assembles to provide:…
**Note: I never printed/tested this. See the note below for an explanation. For my newer designs that I did print, see https://www.prusaprinters.org/prints/10121-dice-tower-and-organizer-plinko-style and…
Plinko Tube Dice Tower This is a dice tower inspired by Plinko mechanics. It's designed to provide fair, random rolls while being easy to print on most 3D printers—no supports required. Dice dropped into the funnel bounce off internal…
Dice tower inspired by Plinko. Printed here in Black PLA from Sunlu, 3% infill with gyroid pattern - 1.5 hours. Maybe it's unlucky, my first roll on it was a 1 on the D20…
This Pachinko-style tower is open in front but does not need a cover glass: the angled pins and walls keep the dice from falling backward. The included slide-on cover seals the tower for dice storage/transport and acts as a tray for the…
Dice tower but plinko style! Will need to supplement this print with a piece of glass or plexiglass. The dimensions are on the picture 164mmx134mmx3.175mm. This should fit all standard sized dice d4's, d6's, d8's, etc etc. Print on its…
A sex game based on Plinko. Take a chance and gamble on what you and your partner will be doing tonight! Where ever the chip lands is what you do! 3D printing settings Print at .2 layer height with a filament swap after layer 10 (2mm).…
you will need to put some rubber bands on these pins 1st picture Pin [File Name] 2nd picture Plinko Board [File Name]
This model will help store most dice and if you put it at the top of the Plinko it will roll the dice for you. P.S. I don't have a 3d printer and I am new to designing 3d prints so if it isn't perfect I am sorry. I also don't know how to…
Based on the 4 jar method of teaching kids to save, this model adds a fun twist. There is a direct slot to each of the jars as well as a random jar selection by use of something similar to the popular game Plinko. Let's say your child…
Plinko is a game in which a falling ball must land in a place at the bottom . Use a Marble ball, it give the best experience Throw the ball into the hole and watch it fall in a satisfying way !!!
ENGLISH : Dice tower made especially for the competition. Fully printable on a prusa mini. The stand can be printed in a stand, but it's a relatively long stitch. I'm going to put a version of the stand withou support, but it'll consume…
This is my entry for the Dice Tower contest. My original idea was a castle with a drawbridge system but I realized I didn't have enough time to model it before the end of the contest so I went with a Plinko game to make it interesting.…
The cheapest acrylic sheet in my local hardware store is 8" x 10", so I wanted to make the most of the surface area by increasing the height of the tower. The new dimensions for the acrylic/polycarbonate sheet are 7 ½" x 4 ½". I had my…
This design is wider than the old one so larger coins should work. Also stopping this print to switch out colors looks great with this model (look at the original post for examples).
