Counting matching models…
GME MB206/MB207 backing plate contoured to the dash trim in the Toyota LandCruiser Prado 150 for easy mounting. Both left and right side trim variant .stl files are provided, use the correct one for the side you wish to attach the mount…
Mine was broken and apparently, I'm not the only one. A useful print to repair an air vent part for Toyota Prado. In the photos, the 1st one is the printed model, in the 2nd one the original part by Toyota.
This is a model of the genuine Toyota part that helps redirect oil draining from your sump. It slots in between the sump and the bar that runs below it, to stop oil splashing onto the bar. This model is slightly oversized, as the vehicle…
The Prado has a lot of contoured surfaces, without having anywhere flat to stick the GME XRS mount this adapter plate fits the bill. Using all the supplied hardware in the GME kit its as simple as taking off the flat plate and replacing…
Ручка двери заднего стекла Toyota Land Cruiser Prado 150, позволяющая закрыть его изнутри. Прикрепляется родными болтами. Просто снимите оригинальную деталь (она крепится клипсами, расположение клипс можно увидеть по отверстиям на…
Prado cool box 6 pack cooler , Using a large Willow ice brick this little bad boy in combination with the aircon cool box of the Prado will keep 6 beers cold all day!
6cm*2.5cm*0.37cm can be scaled as desired 2 models included: 1 with toyota logo on the back, 2 without logo. during printing you can change the filament to another color and the TOYOTA inscription will be in a different color.
CB Radio handset mount for toyota Landcuiser prado 250. Print on it's side, clip the bottom underneath the trim and bend the top back a little to clamp it over the drink holder. Needs 2x M3 nuts for the back - just push them into the…
Ta cansado de deixar seu Soprador jogado em qualquer lugar ou de ver ele caindo o tempo todo por esbarrar nele sem querer? Pois aqui ta a solução! uma estação pra deixar ele de pé com mais charme ;D Recomendação: pode ser impresso com…
This is a slim water tank I designed to fit inside the Toyota Prado rear door cavity. It can be used to store non-drinking water and used for handwashing, cleaning, etc. It should fit on any J150 Prado (roughly 2009–2023) if the rear door…
Original in yellow, my version in orange, I put some extra material in places where it shouldn't matter, and to make it a little tighter.
Ручка двери заднего стекла Toyota Land Cruiser Prado 150, позволяющая закрыть его изнутри. Прикрепляется родными болтами. Просто снимите оригинальную деталь (она крепится клипсами, расположение клипс можно увидеть по отверстиям на…
This adapter allows a phone holder/cradle to be held by the upper left air vent (upper right if the steering wheel is on the wrong side) on 120 Prados, placing the phone in a much higher and more visible position, making it much easier to…
This is a slim water tank I designed to fit inside the Toyota Prado rear door cavity. It can be used to store non-drinking water and used for handwashing, cleaning, etc. It should fit on any J150 Prado (roughly 2009–2023) if the rear door…
Original in yellow, my version in orange, I put some extra material in places where it shouldn't matter, and to make it a little tighter.
Insert for the somewhat useless square cup holder in a Toyota Prado 150 series. This version fits a large (36oz / 1065ml) Yeti bottle and a small tray (to hold fries on a road trip :-)) Also a cutout for a coffee cup handle. It covers the…
A convenient holder for the Fuel Nozzle Pins (thanks to rekrapd for the design, original unmodified file attached as fuel_nozzle_pins_v1.stl to this project in case Thingiverse evaporates) that sits in the fuel filler door on the Toyota…
Plug for the spare wheel cover mounting anchors that remain when you remove the plastic trim bits on a Toyota LandCruiser Prado 150. The pin inside the plug is a simple friction fit into the plastic screw anchor. I've printed these in TPU…
Replacement nylon electric front seat gear for Toyota Land Cruiser, Prado, Toyota Granvia, Toyota Regius Printed in Taulman bridge nylon 2 Variants V1 15mm ID smooth bore V2 approx 14mm ID with splines
I printed in PETG on its side using tree supports for the arms.
The side air conditioning vents in my old beast had become brittle with heat and age and deteriorated. I dismantled the vent units and found both the vertical and horizontal guides needed to be rebuilt. Being unable to find an existing…
Sick of cans or stubbys rolling around in your Prado cool box , print this and off ya go! Printed in PETG .3 or .2 layer height print flat side down I printed with no top or bottom layers to see honey comb effect
6mm wheel spacer for spare tyre to make fitting wheel bags easier Print in place
