Counting matching models…
Tri-Bahtinov Mask for C8 and Edge HD 8 Hyperstar with cooled ZWO/OGMA/Touptek 80mm diameter camera This Tri-bahtinov mask will fit C8 or Edge HD8 in the Hyperstar configuration with out having to remove the camera. outer diameter is 203mm…
Simple case for mp3-player with hanging loop. Printed in TPU with supports. Set top/bottom interface (Z) distance at 0.4 otherwise they're impossible to remove.
A small tube ring for a Touptek 2600 camera which can be fitted with a long M8 screw to attach large 20mm washers as a counter balance for the filter wheel. This is useful if you use a rotator that will change the balance of the image…
I was having issues getting a good FOV for iracing with my Asus Tuf 27'' monitors. I designed these when a previous model I downloaded and printed was too large for the square tubing for the Suptek MD6463 arms. You will need 2 M8x40 bolts…
I designed this simple mounting solution for mounting my grphics tablet to my desk out of the way! It's designed for the Aiptek Media Tablet 14000U (model WMK-H141). Apparently I was too cheap to buy a Wacom! Dimensions… Desk beam…
tripod projection base for the AIPTEK PICO PROJECTOR it fits most tripods
That's it. You can light up the PCB you are looking at
A 15.5mm thick filter drawer for 2 inch filters that takes up lesser backfocus distance compared to commercial options. The drawer uses 2 6x3mm magnets to stay in place. The design uses 4 long (20mm) M3 screws and 2 short M3 screws so the…
I really like this bench power supply from Wanptek. One strange sting about it is a DC output placement at the back. I have designed add-on that is screwed in place of the two front rubber feet. The feet are repositioned on the add-on…
pretty simple really, chop an emergency blanket and tape it on. you will need 2 layers in total to protect your camera enough for a direct look into the sun. magnets are 6X3mm i think? video of my humble non-professional results:
Print settings: Material: PETG Infill: 20% Perimeters: 5 Layer height: 0.2 mm from 0 to 60 mm, and 0.1 mm from 60 to 70 mm to achieve more accurate thread printing. This is a case for the ToupTek AE676C camera. It adds a 1/4" mounting…
The Onshape files can be found here: https://cad.onshape.com/documents/df0b3f0a4026fec2714bccaa/w/c6e1445203c64036d594bf2b/e/e127d6d1c369c972726e20af?renderMode=0&uiState=6988c5b4e200f073ca41870f Feel free to use or modify as you see fit.…
This is a simple design for the Suptek MD6802 desktop screen holder. This is not designed to hold any weight, rather it's supposed to stop the upper part of the rod from shaking, which induces stress on the supporting base. This accessory…
I recently purchased a ToupTek AFW 5x2" filter wheel. Annoyingly my expensive Baader filters were too tall to fit into the filter wheel, as there is a little raised board at the bottom of the AFW with two sensors on which the filters were…
A simple stand for an AGPTEK Smrtwatch
A friend of mine gave me a box of stuff and this thing was in there, so I made a mount for it. A couple differences in the picture and the final upload here. In the back, it was not sitting flush against the back wall for one. I…
A focuser for the touptek. made the same way as my bresser focuser. just smaller and for the gs ar verisons. Its made with a nema 11 motor and 14:1 gearbox from stepperonline.
The ToupTek AFW filter wheel has screw holes either side to attach tilt plate and OAG via screws. If your using the M54 adaptors to attach to telescope and camera (rather than the screws), then the screw holes are not covered and could…
The Onshape files can be found here: https://cad.onshape.com/documents/df0b3f0a4026fec2714bccaa/w/c6e1445203c64036d594bf2b/e/e127d6d1c369c972726e20af?renderMode=0&uiState=6988c5b4e200f073ca41870f Feel free to use or modify as you see fit.…
The ToupTek AFW filter wheel has screw holes either side to attach tilt plate and OAG via screws. If your using the M54 adaptors to attach to telescope and camera (rather than the screws), then the screw holes are not covered and could…
Used pla, but works with whatever. No supports needed, check out my channel: ThatOneAirsofter. Use this one instead: https://www.printables.com/model/1179821-new-kryptek-camo-stencil-re-didv2
