Counting matching models…
This hanger is based off the original hook/hanger that comes with the Milwaukee Quik Lok accessories. I was one short so I measured it up and voila! Printed in PET-G 20% infill 3 walls supports for the key way/hole and the top of the hook
This mount holds any of the Milwaukee Quik-Lok attachments securely to the wall using a snap cradle design. Simply press the shaft into the cradle and it will snap into place snugly and safely. This may work for other brands of similar…
Allows you to wall mount your Milwaukee QUIK-LOK accessories easily. Tested with the trimmer, edger, & hedge trimmers. Not sure how it will handle some of the heavier tools like the power brooms. The V2 holder is a bit thicker because I…
Printed in both PLA and PETG and works fine. Included STL and STP files. Doesn't really need to be printed with supports but I added them for cleaner lines
Inspired by Adam Knepper's design, I have designed this from scratch. All sizes in mm, except for the clamp which is ~1". Added diagonal supports making this version significantly stronger. Also reduced the diameter of the clamp slightly…
Handle for Fiskars replaceable tools. I printed from ASA in two parts (A and B) and glued. SW x2 nozzle 0.4 layer 0.2. You can print with Petg, it should also withstand. A slight cut can be needed on the handle. Fastening to the nit.
Printed with Prusament ASA, 5 perimeters (fully filled walls), adaptive layer height. Wall thickness is 3.5 mm. Bottom plate geometry is shown in a picture. Tested with telescopic handle L.
1x1 Gridfinity Block to hold a thing of flux. Pretty self explanatory Print with supports if you don't want to deal with cleaning up the holes. 2nd photo shows how deep it sits inside the block, proving the need for the height
Thumb screw remixed to work with the Quik Blaster's extended battery tray by OldFusionDesigns. Requires 1 (EA) M3 bolt and 1 (EA) nylon lock nut. Print orientation as imported. Enable support touching build plate (optional).
Gridfinity bin for a Chipquik SMD29130cc flux syringe and up to four needles (which i lost, but the holes are there and i hope they fit).
Simple cap designed specifically for the Chipquik SMD291 with needle (best flux ever)
Red and White QuikSilver Logo
@AcEKrystal designed a really great needle cap for dispensing syringes, but it didn’t fit the ChipQuik flux syringes I use for soldering. After some quick resizing, I created updated dimensions for both 5cc and 10cc syringes. Depending on…
This is a multiboard compatible hanger that I created from 3d scan I made of my Milwaukee Quik Lok 2528-20 power head. Print as oriented Print with tree supports for back multiboard attachments that are included in the file 15% infill
Fiskars Quikfit broken lock - no glue repair / náhrada zlomeného zámku Quikfit bez lepení - print in PETG or any a little bid flexible material / tisknout v PETG (3 perimeters, no infill) - clean the hole from any left broken edges with…
As the GP's in a local practice were struggling to transport all relevant bits for a POK CRP test when going on house calls (keeping reagent tube upright during the car ride), I designed this cup that fits most car cupholders. They now…
I have made a simple wall mount for Milwaukee QUIK-LOK power head, Edger and Trimmer. You have to mount the Tops first and then align the bottoms before screwing them into your preferred walls. I have placed a small slit in the models so,…
toiletpaper hit new one in from the bottom to wipe'r own bottom, faster model, for times speed is necessary. have a pleasant wipe.
Rigel Quikfinder is a popular telescope accessory. This version of the mounting plate (with two additional holes) allows you to use two bands of elastic, string or zip ties to temporarily mount the finder to the scope tube to find the…
A parametric sheath with parameters specific to the Pampered Chef Quikut Paring Knife #1250. These came with carboard sheaths which these replace. The parametric model can be adjusted if the blade fits too tight or loose based on your…
holds 3 rolls of toilet paper and you can quick change the rolls . need to print 6 tabs to go into holder spots. make sure tabs are facing right way when you snap them into position on the frame. one end has a chamfer to signify that…
I needed a cover over my Rigel Finder to prevent it from getting covered with dew. Works as I had hoped.
Rigel Quikfinder FastMagnetFix Update History 1) Upgraded Quickfinder fix Change the fix to remove tilt of original version during usage, causing shift when trying to target. Use “Quickfinder fix v1.1” to fix this. I'll let the original…
Case for the Rigel QuikFinder. I didn't like the idea of just tossing it into my telescope bag unprotected. Printed in PETG at .2mm Uploaded in recommended print orientation.
This device prevents clipping carabiner rotation and side. Be extremely careful when installing, because you need to clip carabiner to quick draw sling!! Based on 16mm Ocun quick draw sling. Print in TPU with 50%-80% infill. If you use…
This fits over the top of a Quik-Tube 8" Form Tube to keep your bolt supported and center while your concrete cures. Fits standard 5/8" bolts (such as J and L bolts) Holder is 1/8" thick with additional 1/8" extensions on wings to keep it…
Print in PETG with supports on, with the recessed socket side down on the build plate.
This is a 3d scan of the milwaukee 2825-20 quik-lok powerhead
This piece allows the controller board of Bolt OS to sit next to a small trigger switch in the pocket in the front of the Quik. You still need to place a selector switch somewhere (in the back there is a good spot). Thus giving your Quik…
Attaches to PrimaLuceLab telescope rings, which have a pair of M6 threaded holes 55mm apart. Print in PETG with supports on, with the recessed socket side down on the build plate.
For people who know the know, TDS 120 fps thanks to the bcar and select fire plates for Bolt OS.
This addon allows for very quick reloads for M72 law 37mm projectiles. Connect your round to the primer holder via tape match or alike, and load into the primer holder w a 209 primer into the primer housing. After closing the latch, you…
This piece allows the controller board of Bolt OS to sit next to a small trigger switch in the pocket in the front of the Quik. You still need to place a selector switch somewhere (in the back there is a good spot). Thus giving your Quik…
Inspired by Adam Knepper's design, I have designed this from scratch. All sizes in mm, except for the clamp which is ~1". Added diagonal supports making this version significantly stronger. Also reduced the diameter of the clamp slightly…
There are several brands of toilet seat with fast release hinges (at least in the United States). I purchased several of these last year, and recently had one of the hinge mounts break. Being made of plastic that can happen. Could not…
These are replacement plugs for the threaded add-on holes in the 1UP USA Quik Rack . These were generated using the Plug that hole OpenSCAD file and tested to fit. Printed in black ASA these have held up nicely in the sun all summer, or…
This is the bottom ring for BRAUN Multiquick Food proc accessory MQ70 bowl. The original ring has stretched out and did not fit the bowl. The ring should be printed using a soft enough TPU/TPE rubber-like filament. I used BFGummy by…
A 1x1 Gridfinity block to hold a plastic syringe (0.35 oz, 10 g/cc) of Chipquik solder flux. Angled for easier access but still fits within the single 1x1 block footprint Magnet recesses on the bottom corners for stability Drain hole so…
For Nesquik or coffee. No support. Print with PLA or PETG - 0.16 mm layer height.
As with all tools, and especially ones that are printed, use this at your own risk. And if you do use it, please use with caution. Make sure your drill bits fit the guides (and that the guides are not worn out). And like Norm Abrams…
no support needed, print any infill at least 2 walls. Grip tape used: https://amzn.to/4bNBoCW
