Counting matching models…
remove the RAM mount ball by unscrewing the centre screw close the hole by screwing the screw back in or replacing it with a suitable M4 screw remove the 4 screws at the corners of the metal plate press 4 pieces of M3 nuts into the…
This stand is designed to not only hold the 1/12th scale model bike, but it also gives you the option to electrify the stand with connection points to the bike. This opens up the option to install LED lights in the bike and have it light…
BMW R1250GS - Keychain - Portachiavi - Porte Clès - 钥匙链 - Schlüsselanhänger Resize to adjust dimension If you download/enjoyed this file, please leave a like - Thx All trademarks, logos and brand names are the property of their respective…
BMW R1250GS Key chain - Portachiavi - Porte Clès - 钥匙链 - Schlüsselanhänger Type B / C / D Resize to adjust dimension If you download/enjoyed this file, please leave a like - Thx All trademarks, logos and brand names are the property of…
BMW R1250GS navigation spacer Print with 20% infill
You need brass inserts instead of nuts. A screw has been added for a more fixed installation. I recommend grinding the tip of middle screw to a point.
These parts allow the Zumo XT to fit into the standard BMW R1250GS Navigator 6 mount and maintains the OEM keyed locking function. The Zumo XT has slightly different dimensions to the OEM system so offset holes need to be drilled through…
I wanted to reduce the screen vibrations on my R1250GS and keep the functionality of easy height adjustment and access to the GPS navigation locking system. I didn't like the commercial options. The system clamps onto the BMW GPS mounting…
Want to change the oil in your BMW 1250 GS yourself, but don't have the right oil filter wrench? Then this tried-and-tested oil filter wrench is just what you need. For 74.6 mm 14-sided original BMW oil filters.
I had a Battery Tender BTL35A480C LiFeP04 battery (linked below but no longer for sale) that came out of another vehicle and I wanted to use it to replace the factory BMW battery that was getting old. It was just slightly too wide to fit…
I was looking for a M16x1.5 petcock for my Aliexpress fuel tank (I'm building a custom scrambler and the petcock that came with the tank is touching the frame, so I needed a more compact petcock). I found a NSR125 petcock which was…
EN: This is a STEP model of a BMW motorcycle key blank. I designed the key blank as accurately as possible based on a laser scan and various measurements. The central longitudinal grooves on both sides are the same for all keys, and the…
This action cam mount is designed for the original left mirror of the BMW R 1250 GS (YOC 2020+). It contains of a bottom part which stabilises the holder and the upper lid with the cam mount. You need 2xM5 screws and (self-locking) nuts…
Make your 1/12th scale model bike glow! Way cooler than a sticker of a light. You'll have to cut out the tail area where this goes. Easy to do with a small hand saw blade. Super glue will hold the light in place when you're ready. Print…
This is a custom made part to replace the cover found behind the divers seat on a Yamaha MT-125/ R125 (2014-2019). Part Number: 5D7-F4796-00-00 Custom made in Autodesk Fusion as a novice. Background When I bought my MT-125 second hand,…
For original BMW crasch cover
Use this plate to easily mount a TomTom in place of a Garmin on your BMW R1200GS or R1250GS. Will likely also work on the BMW S1000XR and other motorcycles with the sat-nav mounted in the same way.
This adapter plate will allow you to use a signal mounting plate from AliExpress and move the camera out further from the body work so you can plug in constant power to the camera while recording or charging the GoPro.
Un piccolo dettaglio per perfezionare la tua Yamaha R125 . Se come me non sopporti la vista della vite di fissaggio della sella, questo tappo è la soluzione definitiva. Copre la vite a vista con un design minimale e pulito, integrandosi…
A tool to torque the clutch and primary drive gear of a Honda CR125 engine, should fit from 1985-2007. Requires a handle to be added, there are two M6-1.0 threaded through holes for the handle. I used a long piece of 1.5in x 0.25in…
This is a spacer for the BMW r1250GS battery compartment. It should also fit the r1250r, and r1250RS Or any motorcycle by scaling the dimensions in slicer Designed to fill that empty gap left by a smaller and lighter lithium battery when…
Zaślepka lagi do YAMAHA YZF-R125 2010R wymiar wewnętrzny 29.7mm Plik jest zrobiny w nad wymiarze tak aby dopasować go papierem ściernym, na ciasno aby nie wypadł. proszę drukować orientacja do góry nogami Pet-G 100% Fork end cap for…
I designed this remote mount for a Yamaha R125 2024. You need a zip tie that is 2 mm wide. It acts as a sort of safety wire if it were to fall off, so don't tighten it too much, the part could break. I also made a cover so you can leave…
I needed a camera that works with my Garmin Zumo XT navigation device on my motorbike All the space on the rear BMW F850 GS is full with extra lights etc. so the only space was under the Vario top box. The screws from the top case are…
The bracket allows you to move the navigation cradle forward and up a bit. By positioning the cradle forward so it is just under the main display in your field of view, it makes it a lot easier to read while riding. I've printed this in…
Chybějící díly pro držák navigace pod štítek pro BMW R1250R odjednaného z aliexpress.
This is a spacer for the BMW r1250GS battery compartment. It should also fit the r1250r, and r1250RS Or any motorcycle by scaling the dimensions in slicer Designed to fill that empty gap left by a smaller and lighter lithium battery when…
This is a custom made part to replace the cover found behind the divers seat on a Yamaha MT-125/ R125 (2014-2019). Part Number: 5D7-F4796-00-00 Custom made in Autodesk Fusion as a novice. Background When I bought my MT-125 second hand,…
For 5-hole rims (cast + spoke) PETG is not absolutely necessary, PLA works. I would recommend using 3 - 4 wall lines and 20 - 30% infill. Layer height 0.2 mm. The brand name is used solely for descriptive purposes to indicate the…
Bracket for mounting second Aux power source i.e touratech twin USB or BMW DIN if not fitted. Needs 2 m6 nuts and longer m6 bolts for fixing Loom cable can be purchased, please message
Clips for 60mm Hub Caps to snap into the hub of a BMW R1250R / RS Hub Caps can be found on Ebay etc. Designed for 60mm caps with 5 clips. Snap off the original clips and glue the model in place. Wire ring clip can be reused, model mounts…
EN I designed three versions, the only difference being the type of nut you use. You can use an M5 threaded nut, a regular nut, or a 20mm diameter knurled nut. You have to pause the print so you can insert the nut or knurled nut. There…
Rotiform_R125 IND Forged 3 piece wheel Another variation based on the Rotiform_R125 IND Forged
Turn your BMW R1250 GS front wheel rim into a clean, functional wall piece. This adapter lets you mount the rim securely to a wall and use it as a premium organizer for things like a garden hose, air hose, extension lead, EV/charger…
a simple replacement for the tail light bracket might work for other bikes
BMW R1250GS Adventure rubber foot pegs I have been testing them for 2 months now and they are working very well. Play around with the filler for hardness. I recommend print it from TPU with fill Gyroid 20% to start with and size 100 to…
For 5-hole rims (cast + spoke) PETG is not absolutely necessary, PLA works. I would recommend using 3 - 4 wall lines and 20 - 30% infill. Layer height 0.2 mm. The brand name is used solely for descriptive purposes to indicate the…
I had my off the shelf extender fall off somehow and I didn't want to spend another $80 on a new one. Made specifically for a 2021 R1250GSA with low suspension, I printed the bottom out of a stiffer TPU, and the top out of PETG, both with…
