Counting matching models…
Ritewing Mini Drak Motor Mount 2814, 25 x 19 and 25 x 25 mount holes pattern. Designed to fit Ritewing Mini Drak. I had Cobra 2814 1800Kv spinning APC 7x5, basically the recommended combo, decided to switch to something more efficient for…
Ritewing Mini Drak Vertical Vertical Stabilizers Skids Designed to fit Ritewing Mini Drak. Provides protection and increased skidding performance.... Recommended print materials: PLA+. PETG. ABS. Print orientation File is oriented…
Ritewing Mini Drak Control Horns Designed to fit as direct drop in for horns supplied in Mini Drak kit. Recommended print materials: Nylon carbon. PETG. ABS Print orientation Everything can be printed normally (as shown). Some specs: Top…
This is a mount that holds the Caddx Vista mount that I designed (you can find that HERE ). To install it, cut off the nose of your Nano Drak (I know, it's nerve-wracking!) right where the grooves for the spars end. Make sure you get it…
Ritewing Mini Drak Bay Covers (hinged in place) Designed to fit Ritewing Mini Drak. Moved RX / VTX to wings and needed something to replace the poor cora covers. Recommended print materials: PLA+. PETG. ABS. Print notes Ensure first layer…
Ritewing Mini Drak servo pockets are direct fit for Corona DS-339MG servos, those are low quality and very sensitive to 1.3Ghz video, they will rattle and behave erratically when the VTX is near by. I use BlueBird BMS-390DMH (Coreless)…
Wing joiner for the Ritewing (Big) Drak 60'' These things will join the fuselage and wings using an O-ring. The system replaces hook and loop tape. Reviewed model from Havardsa to fit a 120mm 120mm 120mm printbed This thing was modified…
March 19, 2020 update: Added a Gopro Hero 8 version. I have my mod of Havardsa's Gopro 3/4 nose ( https://www.thingiverse.com/thing:2859361 ) on my Drak but I just picked up a Gopro 7 which doesn't fit. I took the original and using…
I created this mount so that I could mount a DJI O3 camera in the front nose of the VollStyle RiteWing. This mount should be printed in TPU and is designed to be a sung fit around the O3 camera module. I included screw holes on the inside…
Quick remix of Tom's excellent mount for his Defiant 42. I mirrored it for easier access to the SD card and pushed the camera forward so the print is not in view. Also chopped off the ends so it fits perfectly in the slot I already cut…
Ritewing Mini Drak RX Bay cover, hinged. Designed to fit as direct drop in for stock coraplast bay covers. Introduction Fitting UHF dipole vertically with both elements above the craft. Two small naca ducts provide some cooling intake.…
Electronics bay hood scoop and vent to cool down the ESC and VTX better. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: .12 Infill: 100 Filament: sainsmart TPU Category: R/C Vehicles
*May 13 2018 update: Added a snub nose version for the FPV cam so that the front of the camera is at the edge of the print to avoid seeing the print in the FPV view. I took Havardsa's nice design for a GoPro mount for the Drak and added…
Uses two of the ritewing thumb screw inserts. Printed in Overture HS TPU. Install: Cut the nose off 25mm ahead of the front of the lip of the bay. Use a hot piece of wire to cut the hole for the camera wires. Use the part to mark the…
This is a custom-designed nose piece for the Ritewing Nano Drak, made to fit the DJI Air Unit. Printed in TPU with a 0.2 mm layer height. The design uses 4 M3 x 3.5 mm heat-set inserts, 2x M3 6 mm screws, and 2x M3 30 mm screws for…
